Home › TRANSMISSION ยท A750E AUTOMATIC TRANSMISSION › CLUTCH DRUM AND INPUT SHAFT ASSEMBLY

CLUTCH DRUM AND INPUT SHAFT ASSEMBLY > DISASSEMBLY

for Preparation Click here



1. FIX CLUTCH DRUM AND INPUT SHAFT ASSEMBLY


    D027995E01
  1. Place the oil pump onto the torque converter clutch, and then place the clutch drum and input shaft assembly onto the oil pump.



2. REMOVE REVERSE CLUTCH HUB SUB-ASSEMBLY


    D027996E01
  1. Using a screwdriver, remove the snap ring.



    D027997E01
  1. Remove the reverse clutch hub sub-assembly, reverse clutch reaction sleeve, clutch cushion, plate reverse clutch flange, 5 reverse clutch discs and 4 clutch plates from the clutch drum.



3. REMOVE REVERSE CLUTCH REACTION SLEEVE


    D027998E01
  1. Remove the reverse clutch reaction sleeve from the reverse clutch hub.



4. REMOVE REAR CLUTCH DISC


    D027999E05
  1. Remove the clutch cushion plate, reverse clutch flange, 4 plates and 5 discs from the reverse clutch hub.



5. INSPECT REAR CLUTCH DISC


    D001216E01
  1. Replace all discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) grooves or printed numbers have even a little bit of damage.

    NOTICE:
    Before assembling new discs, soak them in ATF for at least 15 minutes.



6. INSPECT REVERSE CLUTCH HUB SUB-ASSEMBLY


    D028000E01
  1. Using a dial indicator, measure the inside diameter of the reverse clutch hub bushing.

    Standard drum bushing:
    35.812 to 35.837 mm (1.4099 to 1.4109 in.)

    Maximum drum bushing:
    35.887 mm (1.4129 in.)

    1. If the inside diameter is greater than the maximum, replace the reverse clutch hub.



7. REMOVE FORWARD CLUTCH HUB SUB-ASSEMBLY


    D028001E01
  1. Remove the forward clutch hub sub-assembly from the clutch drum.



    D028500E03
  1. Remove the 2 thrust needle roller bearings from the forward clutch hub.



8. INSPECT FORWARD CLUTCH HUB SUB-ASSEMBLY


    D028501E01
  1. Using a dial indicator, measure the inside diameter of the forward clutch hub bushing.

    Standard drum bushing:
    26.037 to 26. 062 mm (1.0251 to 1.0261 in.)

    Maximum drum bushing:
    26.112 mm (1.0280 in.)

    1. If the inside diameter is greater than the maximum, replace the forward clutch hub.



9. REMOVE MULTIPLE DISC CLUTCH HUB


    D028502E01
  1. Remove the multiple disc clutch hub from the clutch drum.



    D028503E02
  1. Remove the No. 2 thrust bearing race and input shaft thrust bearing race rear from the multiple disc clutch hub.



10. REMOVE INPUT SHAFT ASSEMBLY


    D028504E01
  1. Remove the thrust needle roller bearing from the clutch drum.



    D028505E01
  1. Remove the input shaft assembly from the clutch drum.



11. REMOVE INPUT SHAFT OIL SEAL RING


    D029677E01
  1. Remove the 3 oil seal rings from the input shaft.



12. REMOVE FORWARD MULTIPLE DISC CLUTCH DISC


    D028519E01
  1. Using a screwdriver, remove the hole snap ring



    C115806
  1. Remove the 2 flanges, 6 discs and 5 plates from the input shaft.



13. INSPECT FORWARD MULTIPLE DISC CLUTCH DISC


    D001216E01
  1. Replace all discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) grooves or printed numbers have even a little bit of damage.

    NOTICE:
    Before assembling new discs, soak them in ATF for at least 15 minutes.



14. REMOVE NO. 1 CLUTCH BALANCER


    D028521E02
  1. Place SST on the No. 1 clutch balancer, and compress the return spring with a press.

    SST
    09350-30020   (09350-07040, 09350-07070)



    D028522E01
  1. Remove the No. 1 clutch balancer and forward clutch return spring from the input shaft assembly.



    D028523E01
  1. Remove the O-ring from the No. 1 clutch balancer.



15. INSPECT FORWARD CLUTCH RETURN SPRING SUB-ASSEMBLY


    C059838E01
  1. Using a vernier caliper, measure the free length of the spring together with the spring seat.

    Standard free length:
    26.74 mm (1.053 in.)



16. REMOVE FORWARD CLUTCH PISTON


    D028524E01
  1. Holding the forward clutch piston by hand, apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the input shaft to remove the forward clutch piston.



    D028525E01
  1. Remove the 2 O-rings from the forward clutch piston.



17. REMOVE REVERSE CLUTCH FLANGE


    D028506E01
  1. Remove the reverse clutch flange from the clutch drum.



18. REMOVE DIRECT CLUTCH DISK


    D028507E01
  1. Using a screwdriver, remove the 2 hole snap rings from the clutch drum.



    C115805
  1. Remove the reverse clutch flange, 6 plates and 5 discs from the clutch drum.



19. INSPECT DIRECT CLUTCH DISK


    D001216E01
  1. Replace all discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) grooves or printed numbers have even a little bit of damage.

    NOTICE:
    Before assembling new discs, soak them in ATF for at least 15 minutes.



20. REMOVE NO. 3 CLUTCH BALANCER


    D028509E03
  1. Place SST on the No. 3 clutch balancer, and compress the return spring with a press.

    SST
    09387-00070  
    09350-30020   (09350-07070)



21. REMOVE REVERSE CLUTCH RETURN SPRING SUB-ASSEMBLY


    D028510E01
  1. Remove the reverse clutch return spring and O-ring from the reverse clutch piston.



22. INSPECT REVERSE CLUTCH RETURN SPRING SUB-ASSEMBLY


    C059838E01
  1. Using a vernier caliper, measure the free length of the spring together with the spring seat.

    Standard free length:
    26.74 mm (1.053 in.)



23. REMOVE REVERSE CLUTCH PISTON SUB-ASSEMBLY


    D028511E01
  1. Remove the reverse clutch piston, sub-assembly from the clutch drum.



    D028512E01
  1. Remove the O-ring from the reverse clutch piston.



    D028513E01
  1. Remove the O-ring from the clutch drum.



24. REMOVE DIRECT CLUTCH PISTON SUB-ASSEMBLY


    D028514E05
  1. Place SST on the direct clutch piston, and compress the return spring with a press.

    SST
    09320-89010  
    09350-30020   (09350-07070)



    D028515E01
  1. Using 2 screwdrivers, remove the direct clutch piston sub-assembly from the clutch drum.



    D028516E01
  1. Remove the O-ring from the clutch drum.



    D028517E01
  1. Remove the No. 2 clutch balancer and direct clutch return spring sub-assembly from the direct clutch piston.



    D028816E01
  1. Remove the 2 O-rings from the direct clutch piston.



25. INSPECT DIRECT CLUTCH RETURN SPRING SUB-ASSEMBLY


    C059838E01
  1. Using a vernier caliper, measure the free length of the spring together with the spring seat.

    Standard free length:
    19.51 mm (0.768 in.)