DTC P0418 Secondary Air Injection System Control "A" Circuit |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0418 | Both of the following conditions are met, when idling just after cold start (1 trip detection logic):
|
|
| P0418 | Both of the following conditions are met, when idling just after cold start (1 trip detection logic):
|
|
| Related DTCs | P0418: Air pump range check |
| Required sensors/components | Air injection control driver, Air pump |
| Frequency of operation | Continuous |
| Duration | 3 seconds |
| MIL operation | Immediate |
| Sequence operation | None |
| The monitor will run whenever this DTC is not present | None |
| Air pump | Operating |
| Air switching valve | Operating |
| Battery voltage | 8 V or more |
| Ignition switch | ON |
| Starter | OFF |
| Air pump | Not operating |
| Air switching valve | Not operating |
| Battery voltage | 8 V or more |
| Ignition switch | ON |
| Starter | OFF |
| Diagnostic signal duty ratio from air injection control driver | 11 to 29 % |
| Diagnostic signal duty ratio from air injection control driver | 70 to 90 % when secondary air injection system operating and 0 % when secondary air injection system not operating |
![]() |
![]() |
![]() |
| Items | Contents |
| Terminals | CH1: AIDI - E1 |
| Equipment Settings | 5 V/DIV., 20 to 40 ms/DIV. |
| Conditions | Idling |
| AID Diagnostic Signal Waveform | ECM Command | DTC (ECM Output) | Suspected Trouble Area |
| 100 % Duty Ratio See waveform 1 | Any Air Injection (AIR) System operation | P1613 |
|
| 0 % Duty Ratio See waveform 2 | AIR System: ON (Air pump ON, ASV ON) | P1613 |
|
| AIR System: OFF (Air pump OFF, ASV OFF) | - |
| |
| 20 % Duty Ratio See waveform 3 | Air Pump: ON | P0418 |
|
| Air Pump: OFF | P0418 |
| |
| 40 % Duty Ratio See waveform 4 | ASV: ON | P0412 |
|
| ASV: OFF | P0412 |
| |
| 80 % Duty Ratio See waveform 5 | AIR System: OFF (Air pump OFF, ASV OFF) | P1613 |
|
| AIR System: ON (Air pump ON, ASV ON) | - |
| |
| Excluding Above (excluding 0, 20, 40, 80, 100 % duty) | - | P1613 |
|
| Waveform 1 |
![]() |
| Waveform 2 |
![]() |
| Waveform 3 |
![]() |
| Waveform 4 |
![]() |
| Waveform 5 |
![]() |
| 1.INSPECT AIR PUMP |
![]() |
Remove the intake manifold .
Disconnect the A46 air pump connector.
Measure the resistance of the air pump.
| Tester Connection | Specified Condition |
| 1 - 2 | 0.4 to 1.0 Ω |
Reconnect the air pump connector.
|
| ||||
| OK | |
| 2.CHECK HARNESS AND CONNECTOR (AIR PUMP - BODY GROUND) |
![]() |
Remove the intake manifold .
Disconnect the A46 air pump connector.
Measure the resistance of the wire harness side connectors and body ground.
| Tester Connection | Specified Condition |
| A46-1 - Body ground | Below 1 Ω |
Reconnect the air pump connector.
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (AIR INJECTION CONTROL DRIVER - AIR PUMP) |
![]() |
Remove the intake manifold .
Disconnect the A43 air injection driver connector.
Disconnect the A46 air pump connector.
Measure the resistance between the wire harness side connectors.
| Tester Connection | Specified Condition |
| VP (A43-2) - A46-2 | Below 1 Ω |
| VP (A43-2) or A46-2 - Body ground | 10 kΩ or higher |
Reconnect the air injection driver connector.
Reconnect the air pump connector.
|
| ||||
| OK | ||
| ||