Home › BODY ELECTRICAL › AUDIO / VISUAL › STEERING PAD SWITCH

STEERING PAD SWITCH > INSPECTION

for Preparation Click here



1. INSPECT STEERING PAD SWITCH LH


  1. Measure the resistance according to the values in the table below.


    I039169E02


    Standard resistance:

    Tester connection
    Condition
    Specified condition
    AU1 - EAU
    No switch is pushed
    Approx. 100 kΩ
    AU1 - EAU
    SEEK+ switch: push
    Approx. 0 Ω
    AU1 - EAU
    SEEK- switch: push
    Approx. 0.3 kΩ
    AU1 - EAU
    VOL+ switch: push
    Approx. 1 kΩ
    AU1 - EAU
    VOL- switch: push
    Approx. 3.1 kΩ
    AU2 - EAU
    No switch is pushed
    Approx. 100 kΩ
    AU2 - EAU
    MODE switch: push
    Approx. 0 Ω

    If the result is not as specified, replace the steering pad switch LH.



2. INSPECT STEERING PAD SWITCH RH (w/ Navigation System)


  1. Inspect steering pad switch assembly.



    1. Measure the resistance according to the values in the table below.


      E120112E01


      Standard resistance:

      Tester connection
      Condition
      Specified condition
      AU1 - EAU
      No switch is pushed
      Approx. 100 kΩ
      AU1 - EAU
      SEEK+ switch: push
      Approx. 0 Ω
      AU1 - EAU
      SEEK- switch: push
      Approx. 0.3 kΩ
      AU1 - EAU
      VOL+ switch: push
      Approx. 1 kΩ
      AU1 - EAU
      VOL- switch: push
      Approx. 3.1 kΩ
      AU2 - EAU
      No switch is pushed
      Approx. 100 kΩ
      AU2 - EAU
      MODE switch: push
      Approx. 0 Ω
      AU2 - EAU
      VOICE switch: push
      Approx. 3.1 kΩ
      AU2 - EAU
      ON HOOK switch: push
      Approx. 0.3 kΩ
      AU2 - EAU
      OFF HOOK switch: push
      Approx. 1 kΩ



  1. Inspect steering pad switch cable.


    E120113E02


    1. Measure the resistance according to the values in the table below.

      Standard resistance:

      Tester connection
      Condition
      Specified condition
      B-1 - C-1
      Always
      Below 1 Ω
      B-2 - C-2
      Always
      Below 1 Ω
      B-3 - C-3
      Always
      Below 1 Ω
      B-4 - C-4
      Always
      Below 1 Ω
      B-5 - C-5
      Always
      Below 1 Ω
      B-6 - C-6
      Always
      Below 1 Ω
      B-7 - C-7
      Always
      Below 1 Ω
      B-8 - C-8
      Always
      Below 1 Ω
      B-1 - Body ground
      Always
      10 kΩ or higher
      B-2 - Body ground
      Always
      10 kΩ or higher
      B-3 - Body ground
      Always
      10 kΩ or higher
      B-4 - Body ground
      Always
      10 kΩ or higher
      B-5 - Body ground
      Always
      10 kΩ or higher
      B-6 - Body ground
      Always
      10 kΩ or higher
      B-7 - Body ground
      Always
      10 kΩ or higher
      B-8 - Body ground
      Always
      10 kΩ or higher

      If the result is not as specified, replace the steering pad switch cable.



  1. Inspect steering pad switch RH.


    E120114E01


    1. Measure the resistance according to the values in the table below.

      Standard resistance:

      Tester connection
      Condition
      Specified condition
      AU2 (B-4) - EAU (B-2)
      No switch is pushed
      10 kΩ or higher
      AU2 (B-5) - EAU (B-3)
      AU2 (B-5) - EAU (B-2)
      AU2 (B-4) - EAU (B-3)
      AU2 (B-4) - EAU (B-2)
      VOICE switch: push
      Approx. 3.1 kΩ
      AU2 (B-5) - EAU (B-3)
      AU2 (B-5) - EAU (B-2)
      AU2 (B-4) - EAU (B-3)
      AU2 (B-4) - EAU (B-2)
      ON HOOK switch: push
      Approx. 0.3 kΩ
      AU2 (B-5) - EAU (B-3)
      AU2 (B-5) - EAU (B-2)
      AU2 (B-4) - EAU (B-3)
      AU2 (B-4) - EAU (B-2)
      OFF HOOK switch: push
      Approx. 1 kΩ
      AU2 (B-5) - EAU (B-3)
      AU2 (B-5) - EAU (B-2)
      AU2 (B-4) - EAU (B-3)

      If the result is not as specified, replace the steering pad switch RH.