Home › DRIVE LINE ยท DIFFERENTIAL › 1GR-FE FRONT DIFFERENTIAL CARRIER ASSEMBLY (for 4WD)

1GR-FE FRONT DIFFERENTIAL CARRIER ASSEMBLY (for 4WD) > DISASSEMBLY

for Preparation Click here



1. REMOVE DIFFERENTIAL VACUUM ACTUATOR ASSEMBLY


    G023135
  1. Remove the 4 bolts.

  1. Using a hammer, handle, remove the actuator assembly.



2. REMOVE FRONT DIFFERENTIAL TUBE ASSEMBLY


    G023134
  1. Remove the 4 bolts.

  1. Using a plastic hammer, remove the differential tube.



3. REMOVE DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL


    R013209E01
  1. Using SST, remove the oil seal.

    SST
    09308-00010  



4. REMOVE DIFFERENTIAL SIDE GEAR INTER SHAFT SUB-ASSEMBLY


    G023136E02
  1. Using SST, remove the side gear inter shaft.

    SST
    09350-20015   (09369-20040)
    09950-40011   (09951-04010, 09952-04010, 09953-04020, 09954-04010, 09955-04011, 09957-04010, 09958-04011)

  1. Remove the snap ring from the side gear inter shaft.



5. REMOVE FRONT DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY


    F044234E01
  1. Using SST and a hammer, remove the nut.

    SST
    09930-00010  



    SA02349E05
  1. Using SST to hold the companion flange, remove the nut.

    SST
    09330-00021   (09330-00030)



    F052175E01
  1. Using SST, remove the companion flange.

    SST
    09950-30012   (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03020)



6. REMOVE FRONT DIFFERENTIAL CARRIER OIL SEAL


    SA02348E03
  1. Using SST, remove the oil seal from the differential carrier assembly.

    SST
    09308-10010  



7. REMOVE FRONT DIFFERENTIAL DRIVE PINION OIL SLINGER


8. REMOVE FRONT DRIVE PINION REAR TAPERED ROLLER BEARING


    Z000641E04
  1. Using SST, remove the rear bearing from the drive pinion.

    SST
    09556-22010  

  1. Remove the bearing spacer.



9. REMOVE DIFFERENTIAL SIDE BEARING RETAINER
  1. Using a screwdriver, remove the union.

  1. Remove the 10 bolts and tap out the side bearing retainer with a plastic hammer.



10. REMOVE DIFFERENTIAL CASE ASSEMBLY


11. REMOVE DIFFERENTIAL DRIVE PINION


12. REMOVE FRONT DRIVE PINION FRONT TAPERED ROLLER BEARING


    R002482E02
  1. Using SST and a press, remove the front bearing and washer from the drive pinion.

    SST
    09950-00020  

    HINT:
    If the drive gear or ring gear is damaged, replace them as a set.



13. REMOVE FRONT BEARING OUTER RACE


    R013226
  1. Using a brass bar and a hammer, remove the front bearing outer race.



14. REMOVE REAR BEARING OUTER RACE


    F044257E01
  1. Using SST, remove the rear bearing outer race.

    SST
    09502-12010  
    09612-65014   (09612-01020, 09612-01050)

  1. Using a brass bar and a hammer, remove the oil storage ring.



15. REMOVE SIDE BEARING OUTER RACE

HINT:
  1. Measure the plate washer and note its thickness.
  2. Tag the bearing outer races to show the location for reassembly.



    R013211E01
  1. Using SST and a press, remove the outer race and plate washer from the bearing retainer.

    SST
    09950-60020   (09951-00680)
    09950-70010   (09951-07150)



    R013213E01
  1. Using SST and a press, remove the outer race and plate washer from the differential carrier assembly.

    SST
    09950-60020   (09951-00680)
    09950-70010   (09951-07150)



16. REMOVE DIFFERENTIAL RING GEAR
  1. Place matchmarks on the ring gear and differential case assembly.

  1. Remove the 10 bolts.

  1. Using a plastic hammer, tap on the ring gear to separate it from the differential case assembly.



17. REMOVE FRONT DIFFERENTIAL CASE BEARING


    R011392E02
  1. Using SST, remove the 2 differential case bearings from the differential case assembly.

    SST
    09950-60010   (09951-00390)
    09950-40011   (09951-04020, 09952-04010, 09953-04030, 09954-04010, 09955-04061, 09957-04010, 09958-04011)

    HINT:
    Fix the claws of SST into the notch in the differential case assembly.



18. DISASSEMBLE DIFFERENTIAL CASE


    RA00997
  1. Using a pin punch and a hammer, remove the straight pin.

  1. Remove these parts from the differential case assembly.

    1. 2 Differential side gears

    2. 2 Differential side gear thrust washers

    3. Differential pinion shaft

    4. 2 Differential pinion gears

    5. 2 Differential pinion gear thrust washers



19. INSPECT DIFFERENTIAL GEAR KIT
  1. Check that there is no damage to the pinion gear and side gear.
    If the pinion gear and/or side gear is damaged, replace the differential gear kit.



20. INSPECT FRONT DIFFERENTIAL CASE
  1. Check that the differential case assembly is not damaged.
    If the differential case assembly is damaged, replace it.



21. REMOVE FRONT DIFFERENTIAL SIDE GEAR NEEDLE ROLLER BEARING


    SA00353
  1. Using a brass bar and hammer, remove the 2 bearings.



22. REMOVE DIFFERENTIAL CLUTCH HUB


    G023137
  1. Using a snap ring expander, remove the snap ring.

  1. Remove the differential clutch hub.



23. REMOVE DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL


    R013199E01
  1. Using SST, remove the oil seal from the differential tube.

    SST
    09308-00010  



24. REMOVE DIFFERENTIAL SIDE GEAR SHAFT SUB-ASSEMBLY RH


    C097022
  1. Using a snap ring expander, remove the snap ring.

  1. Remove the side gear shaft from the differential tube.



25. REMOVE FRONT DIFFERENTIAL SIDE GEAR SHAFT RH BEARING


    R013420E02
  1. Using a snap ring expander, remove the snap ring.

  1. Using SST, a brass bar and a press, remove the bearing.

    SST
    09950-00020  

    NOTICE:
    Do not damage the bearing.



26. REMOVE FRONT DIFFERENTIAL DUST DEFLECTOR


    R004465E01
  1. Using SST, a socket wrench and a press, remove the dust deflector.

    SST
    09950-00020  



27. INSPECT DIFFERENTIAL CLUTCH SLEEVE AND DIFFERENTIAL CLUTCH HUB


    G023141
  1. Check for wear and damage to the clutch hub and clutch sleeve.
    If necessary, replace them.

  1. Check that the clutch sleeve slides smoothly on the clutch hub.



28. INSPECT DIFFERENTIAL CLUTCH SLEEVE AND DIFFERENTIAL SIDE GEAR INTER SHAFT


    G023144
  1. Check for wear and damage to the clutch hub and side gear inter shaft.

  1. Check that the clutch sleeve slides smoothly on the side gear inter shaft.



29. INSPECT DIFFERENTIAL CLUTCH SLEEVE AND CLUTCH SLEEVE FORK CLEARANCE


    G023142
  1. Using a feeler gauge, measure the clearance between the sleeve fork and clutch sleeve.

    Maximum clearance:
    0.35 mm (0.0138 in.)

    If the clearance exceeds the maximum, replace the fork or clutch sleeve.