Home › DRIVE LINE ยท DIFFERENTIAL › 2UZ-FE FRONT DIFFERENTIAL CARRIER ASSEMBLY (for 4WD)

2UZ-FE FRONT DIFFERENTIAL CARRIER ASSEMBLY (for 4WD) > DISASSEMBLY

for Preparation Click here



1. REMOVE FRONT DIFFERENTIAL TUBE ASSEMBLY


    C097021
  1. Remove the 4 bolts.

  1. Using a plastic hammer, remove the differential tube.



2. REMOVE DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL


    R013209E01
  1. Using SST, remove the oil seal.

    SST
    09308-00010  



3. REMOVE FRONT DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY


    F044234E01
  1. Using SST and a hammer, remove the nut.

    SST
    09930-00010  



    SA02349E05
  1. Using SST to hold the companion flange, remove the nut.

    SST
    09330-00021   (09330-00030)



    F052175E01
  1. Using SST, remove the companion flange.

    SST
    09950-30012   (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03020)



4. REMOVE FRONT DIFFERENTIAL CARRIER OIL SEAL


    SA02348E03
  1. Using SST, remove the oil seal from the differential carrier assembly.

    SST
    09308-10010  



5. REMOVE FRONT DIFFERENTIAL DRIVE PINION OIL SLINGER


6. REMOVE FRONT DRIVE PINION REAR TAPERED ROLLER BEARING


    Z000641E04
  1. Using SST, remove the rear bearing from the drive pinion.

    SST
    09556-22010  

  1. Remove the bearing spacer.



7. REMOVE DIFFERENTIAL SIDE BEARING RETAINER
  1. Using a screwdriver, remove the union.

  1. Remove the 10 bolts and tap out the side bearing retainer with a plastic hammer.



8. REMOVE DIFFERENTIAL CASE ASSEMBLY


9. REMOVE DIFFERENTIAL DRIVE PINION


10. REMOVE FRONT DRIVE PINION FRONT TAPERED ROLLER BEARING


    R002482E02
  1. Using SST and a press, remove the front bearing and washer from the drive pinion.

    SST
    09950-00020  

    HINT:
    If the drive gear or ring gear is damaged, replace them as a set.



11. REMOVE FRONT BEARING OUTER RACE


    R013226
  1. Using a brass bar and a hammer, remove the front bearing outer race.



12. REMOVE REAR BEARING OUTER RACE


    F044257E01
  1. Using SST, remove the rear bearing outer race.

    SST
    09502-12010  
    09612-65014   (09612-01020, 09612-01050)

  1. Using a brass bar and a hammer, remove the oil storage ring.



13. REMOVE SIDE BEARING OUTER RACE

HINT:
  1. Measure the plate washer and note its thickness.
  2. Tag the bearing outer races to show the location for reassembly.



    R013211E01
  1. Using SST and a press, remove the outer race and plate washer from the bearing retainer.

    SST
    09950-60020   (09951-00680)
    09950-70010   (09951-07150)



    R013213E01
  1. Using SST and a press, remove the outer race and plate washer from the differential carrier assembly.

    SST
    09950-60020   (09951-00680)
    09950-70010   (09951-07150)



14. REMOVE DIFFERENTIAL RING GEAR
  1. Place matchmarks on the ring gear and differential case assembly.

  1. Remove the 10 bolts.

  1. Using a plastic hammer, tap on the ring gear to separate it from the differential case assembly.



15. REMOVE FRONT DIFFERENTIAL CASE BEARING


    R011392E02
  1. Using SST, remove the 2 differential case bearings from the differential case assembly.

    SST
    09950-60010   (09951-00390)
    09950-40011   (09951-04020, 09952-04010, 09953-04030, 09954-04010, 09955-04061, 09957-04010, 09958-04011)

    HINT:
    Fix the claws of SST into the notch in the differential case assembly.



16. DISASSEMBLE DIFFERENTIAL CASE


    RA00997
  1. Using a pin punch and a hammer, remove the straight pin.

  1. Remove these parts from the differential case assembly.

    1. 2 Differential side gears

    2. 2 Differential side gear thrust washers

    3. Differential pinion shaft

    4. 2 Differential pinion gears

    5. 2 Differential pinion gear thrust washers



17. INSPECT DIFFERENTIAL GEAR KIT
  1. Check that there is no damage to the pinion gear and side gear.
    If the pinion gear and/or side gear is damaged, replace the differential gear kit.



18. INSPECT FRONT DIFFERENTIAL CASE
  1. Check that the differential case assembly is not damaged.
    If the differential case assembly is damaged, replace it.



19. REMOVE DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL


    R013199E01
  1. Using SST, remove the oil seal from the differential tube.

    SST
    09308-00010  



20. REMOVE DIFFERENTIAL SIDE GEAR SHAFT SUB-ASSEMBLY RH


    C097022
  1. Using a snap ring expander, remove the snap ring.

  1. Remove the side gear shaft from the differential tube.



21. REMOVE FRONT DIFFERENTIAL SIDE GEAR SHAFT RH BEARING


    R013420E02
  1. Using a snap ring expander, remove the snap ring.

  1. Using SST, a brass bar and a press, remove the bearing.

    SST
    09950-00020  

    NOTICE:
    Do not damage the bearing.



22. REMOVE FRONT DIFFERENTIAL DUST DEFLECTOR


    R004465E01
  1. Using SST, a socket wrench and a press, remove the dust deflector.

    SST
    09950-00020