Home › DRIVE LINE ยท DIFFERENTIAL › 2UZ-FE FRONT DIFFERENTIAL CARRIER ASSEMBLY (for 4WD)

2UZ-FE FRONT DIFFERENTIAL CARRIER ASSEMBLY (for 4WD) > REASSEMBLY

for Preparation Click here



1. INSTALL FRONT DIFFERENTIAL DUST DEFLECTOR


    G022166E01
  1. Using a steel plate and a press, install a new dust deflector.

    NOTICE:
    Do not damage the dust deflector.



2. INSTALL FRONT DIFFERENTIAL SIDE GEAR SHAFT RH BEARING


    R013421E02
  1. Using SST and a press, install the bearing.

    SST
    09223-00010  

  1. Using a snap ring expander, install the snap ring.



3. INSTALL DIFFERENTIAL SIDE GEAR SHAFT SUB-ASSEMBLY RH


    C097022
  1. Install the side gear shaft into the differential tube.

  1. Using snap ring pliers, install the snap ring.



4. INSTALL DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL


    R013419E01
  1. Using SST and a plastic hammer, install a new oil seal.

    SST
    09608-32010  

    Oil seal drive in depth:
    4.8 to 5.8 mm (0.1890 to 0.2284 in.)

  1. Coat the oil seal lip with MP grease.



5. INSTALL FRONT DIFFERENTIAL CASE


    FA01121
  1. Install the 2 proper thrust washers onto the 2 side gears.

    HINT:
    Using the table below, select the thrust washer which will ensure that the backlash is within the specifications.

    Washer thickness 
    Thickness mm (in.)
    Thickness mm (in.)
    1.48 to 1.52 (0.0583 to 0.0598)
    1.73 to 1.77 (0.0681 to 0.0697)
    1.53 to 1.57 (0.0602 to 0.0618)
    1.78 to 1.82 (0.0701 to 0.0717)
    1.58 to 1.62 (0.0622 to 0.0638)
    1.83 to 1.87 (0.0720 to 0.0736)
    1.63 to 1.67 (0.0642 to 0.0657)
    1.88 to 1.92 (0.0740 to 0.0756)
    1.68 to 1.72 (0.0661 to 0.0677)
    -

  1. Install the 2 side gears, 2 side gear thrust washers, 2 pinion gears, 2 pinion gear thrust washers and pinion shaft into the differential case assembly.

    HINT:
    Align the holes of the differential case assembly and pinion shaft.



  1. Measure the side gear backlash.



      F043636
    1. Using a dial indicator, measure the side gear backlash while holding one pinion gear toward the differential case assembly.

      Backlash:
      0 to 0.15 mm (0 to 0.0059 in.)

      If the backlash is not within the specification, install a side gear thrust washer with a different thickness.



    FA01124
  1. Using a pin punch and hammer, install the straight pin through the differential case assembly and hole of the pinion shaft.

  1. Stake the differential case assembly.



6. INSTALL DIFFERENTIAL RING GEAR


    SA02160E02
  1. Clean the contact surfaces of the differential case assembly and ring gear.

  1. Heat the ring gear to about 100°C (212°F) in boiling water.

  1. Carefully take the ring gear out of the boiling water.

  1. After any moisture on the ring gear has completely evaporated, quickly install the ring gear onto the differential case assembly.

    HINT:
    Align the matchmarks on the ring gear and differential case assembly.

  1. Temporarily install 5 new lock plates and 10 bolts so that the bolt holes in the ring gear and differential case assembly are aligned.

  1. After the ring gear has cooled sufficiently, tighten the ring gear set bolts to which thread lock has been applied.

    Torque:
    97 N*m{ 985 kgf*cm , 71 ft.*lbf }



7. INSTALL FRONT DIFFERENTIAL CASE BEARING


    R013784E01
  1. Using SST and a press, install the 2 differential case bearings into the differential case assembly.

    SST
    09226-10010  



8. INSTALL SIDE BEARING OUTER RACE

HINT:
When replacing the 2 differential case bearings, fit 2 of the thinnest new washers to each bearing and when reusing the bearings, fit washers of the same thickness as those removed.

  1. Install a new plate washer to the side bearing retainer.



    R013375E02
  1. Using SST and a press, install the bearing outer race onto the differential case bearing retainer assembly.

    SST
    09950-60020   (09951-00810)
    09950-70010   (09951-07150)

  1. Install a new plate washer onto the differential carrier assembly.



    R013376E02
  1. Using SST and a press, install the bearing outer race onto the differential carrier assembly.

    SST
    09950-60020   (09951-00810)
    09950-70010   (09951-07150)



9. INSTALL FRONT BEARING OUTER RACE


    R013281E02
  1. Using SST, install the outer race.

    SST
    09950-00020   (09951-00680, 09951-00890)



10. INSTALL REAR BEARING OUTER RACE
  1. Install the oil storage ring.

  1. Using SST, install the outer race.

    SST
    09950-00020   (09951-00680, 09951-00890)



11. INSTALL FRONT DRIVE PINION FRONT TAPERED ROLLER BEARING
  1. Install the washer onto the drive pinion.

    HINT:
    First, fit a washer of the same thickness as the removed washer, then after checking the tooth contact pattern, replace the washer with one of a differential thickness if necessary.



    R001197E01
  1. Using SST and a press, install the front bearing onto the drive pinion.

    SST
    09506-30012  



12. INSPECT DIFFERENTIAL DRIVE PINION PRELOAD
  1. Install the drive pinion.

    HINT:
    Assemble the spacer and oil seal after adjusting the ring gear tooth contact pattern.



    R011163E05
  1. Using SST, install the rear bearing, oil slinger and companion flange.

    SST
    09950-30012   (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03020)

  1. Coat the threads of the nut with hypoid gear oil.



    SA02347E03
  1. Adjust the drive pinion preload by tightening the companion flange nut.

  1. Using SST to hold the companion flange, tighten the nut.

    SST
    09330-00021   (09330-00030)

    NOTICE:
    As there is no spacer, tighten the nut a little at a time, being careful not to overtighten it.



    SA02352
  1. Using a torque wrench, measure the preload of the backlash between the drive pinion and ring gear.

    Preload (at starting):
    Bearing
    Standard
    New
    0.98 to 1.57 N*m (10 to 16 kgf*cm, 8.7 to 13.9 in.*lbf)
    Reused
    0.49 to 0.78 N*m (5 to 8 kgf*cm, 4.3 to 6.9 in.*lbf)

    If necessary, disassemble and inspect the differential assembly.



13. INSTALL DIFFERENTIAL CASE ASSEMBLY


14. ADJUST BACKLASH DIFFERENTIAL RING GEAR AND DIFFERENTIAL DRIVE PINION
  1. Install the side bearing retainer with the 10 bolts.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }



    R012683E03
  1. Using SST and a dial indicator, measure the ring gear backlash.

    SST
    09564-32011  

    Backlash:
    0.13 to 0.18 mm (0.0051 to 0.0071 in.)

  1. If it is not within the specification, adjust it by either increasing or decreasing the thickness of the washers on both sides by an equal amount.

    HINT:
    There should be no clearance between the plate washer and differential case.
    Make sure that there is ring gear backlash.


    Washer thickness 
    Thickness mm (in.)
    Thickness mm (in.)
    Thickness mm (in.)
    1.59 to 1.61 (0.0626 to 0.0634)
    1.89 to 1.91 (0.0744 to 0.0752)
    2.19 to 2.21 (0.0862 to 0.0870)
    1.62 to 1.64 (0.0638 to 0.0646)
    1.92 to 1.94 (0.0756 to 0.0764)
    2.22 to 2.24 (0.0874 to 0.0882)
    1.65 to 1.67 (0.0650 to 0.0657)
    1.95 to 1.97 (0.0768 to 0.0776)
    2.25 to 2.27 (0.0886 to 0.0894)
    1.68 to 1.70 (0.0661 to 0.0669)
    1.98 to 2.00 (0.0780 to 0.0787)
    2.28 to 2.30 (0.0898 to 0.0906)
    1.71 to 1.73 (0.0673 to 0.0681)
    2.01 to 2.03 (0.0791 to 0.0800)
    2.31 to 2.33 (0.0909 to 0.0917)
    1.74 to 1.76 (0.0685 to 0.0693)
    2.04 to 2.06 (0.0803 to 0.0811)
    2.34 to 2.36 (0.0921 to 0.0929)
    1.77 to 1.79 (0.0697 to 0.0705)
    2.07 to 2.09 (0.0815 to 0.0823)
    2.37 to 2.39 (0.0933 to 0.0941)
    1.80 to 1.82 (0.0709 to 0.0717)
    2.10 to 2.12 (0.0827 to 0.0835)
    2.40 to 2.42 (0.0945 to 0.0953)
    1.83 to 1.85 (0.0720 to 0.0728)
    2.13 to 2.15 (0.0839 to 0.0846)
    2.43 to 2.45 (0.0957 to 0.0965)
    1.86 to 1.88 (0.0732 to 0.0740)
    2.16 to 2.18 (0.0850 to 0.0858)
    2.46 to 2.48 (0.0969 to 0.0976)



15. INSPECT TOTAL PRELOAD


    SA02352
  1. Using a torque wrench, measure the preload with the teeth of the drive pinion and ring gear in contact.

    Total preload (at starting):
    Drive pinion preload plus 0.25 to 0.45 N*m (2.5 to 4.6 kgf*cm, 2.2 to 4.0 in.*lbf)

    If necessary, disassemble and inspect the differential.



16. INSPECT TOOTH CONTACT BETWEEN RING GEAR AND DRIVE PINION
  1. Remove the side bearing retainer and differential case assembly.



    R013220
  1. Coat 3 or 4 teeth at 3 different positions on the ring gear with red lead.

  1. Install the differential case assembly and side bearing retainer.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }

  1. Hold the companion flange firmly and rotate the ring gear in both directions.

  1. Remove the differential case, side bearing retainer and differential case assembly.



  1. Inspect the tooth contact pattern.


    Z000699E01

    If the teeth are not engaged properly, use the following chart to select the appropriate washer for correction.

    FA02008E01

    Washer thickness 
    Thickness mm (in.)
    Thickness mm (in.)
    Thickness mm (in.)
    1.69 to 1.71 (0.0665 to 0.0673)
    1.93 to 1.95 (0.0760 to 0.0768)
    2.17 to 2.19 (0.0854 to 0.0862)
    1.72 to 1.74 (0.0677 to 0.0685)
    1.96 to 1.98 (0.0772 to 0.0780)
    2.20 to 2.22 (0.0866 to 0.0874)
    1.75 to 1.77 (0.0689 to 0.0697)
    1.99 to 2.01 (0.0783 to 0.0791)
    2.23 to 2.25 (0.0878 to 0.0886)
    1.78 to 1.80 (0.0701 to 0.0709)
    2.02 to 2.04 (0.0795 to 0.0803)
    2.26 to 2.28 (0.0890 to 0.0898)
    1.81 to 1.83 (0.0713 to 0.0720)
    2.05 to 2.07 (0.0807 to 0.0815)
    2.29 to 2.31 (0.0902 to 0.0909)
    1.84 to 1.86 (0.0724 to 0.0732)
    2.08 to 2.10 (0.0819 to 0.0827)
    2.32 to 2.34 (0.0913 to 0.0921)
    1.87 to 1.89 (0.0736 to 0.0744)
    2.11 to 2.13 (0.0831 to 0.0839)
    -
    1.90 to 1.92 (0.0748 to 0.0756)
    2.14 to 2.16 (0.0843 to 0.0850)
    -

  1. Using SST, remove the companion flange and oil slinger.

    SST
    09330-00021   (09330-00030)
    09950-30012   (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03020)

  1. Using SST, remove the rear bearing from the drive pinion.

    SST
    09556-22010  



17. INSTALL FRONT DIFFERENTIAL DRIVE PINION BEARING SPACER
  1. Install a new bearing spacer and oil storage ring.



18. INSTALL FRONT DRIVE PINION REAR TAPERED ROLLER BEARING


19. INSTALL FRONT DIFFERENTIAL DRIVE PINION OIL SLINGER


20. INSTALL FRONT DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY FRONT
  1. Place the companion flange on the drive pinion.

  1. Coat the threads of a new nut with hypoid gear oil LSD.



    R011163E06
  1. Using SST and the companion flange, install the rear tapered roller bearing, then remove the companion flange.

    SST
    09950-30012   (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03020)



21. INSTALL FRONT DIFFERENTIAL CARRIER OIL SEAL


    R013417E02
  1. Using SST and a hammer, install the oil seal.

    SST
    09330-00021   (09330-00030)
    09554-22010  

    Oil seal drive in depth:
    3.9 to 4.8 mm (0.153 to 0.189 in.)

  1. Coat the oil seal lip with MP grease.



    SA02351E05
  1. Using SST to hold the flange, tighten the nut.

    Torque:
    370 N*m{ 3,770 kgf*cm , 273 ft.*lbf }



22. INSTALL DIFFERENTIAL SIDE BEARING RETAINER


    R013200E02
  1. Remove any old FIPG material and be careful not to drop oil on the contact surfaces of the differential carrier and side bearing retainer.

  1. Clean the contact surfaces of any residual FIPG material using gasoline or alcohol.

  1. Apply FIPG to the side bearing retainer, as shown.

    FIPG:
    Part No. 08826-00090, THREE BOND 1281 or equivalent

    HINT:
    Install the side bearing retainer within 10 minutes of applying FIPG.

  1. Install the side bearing retainer with the 10 bolts.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }

  1. Install the union.



23. INSPECT DIFFERENTIAL DRIVE PINION PRELOAD


    SA02352
  1. Using a torque wrench, measure the preload of the backlash between the drive pinion and ring gear.

    Preload (at starting):
    Bearing
    Standard
    New
    0.98 to 1.57 N*m (10 to 16 kgf*cm, 8.7 to 13.9 in.*lbf)
    Reused
    0.49 to 0.78 N*m (5 to 8 kgf*cm, 4.3 to 6.9 in.*lbf)

    If the preload is greater than the specification, replace the bearing spacer.
    If the preload is less than the specification, retighten the nut to 13 N*m (130 kgf*cm, 9 ft*lbf) a little at a time until the specified preload is reached.

    Torque:
    370 N*m{ 3,773 kgf*cm , 273 ft.*lbf } or less

    If the maximum torque is exceeded while retightening the nut, replace the bearing spacer and repair the preload procedure. Do not loosen the nut to reduce the preload.



24. INSPECT TOTAL PRELOAD


25. INSPECT BACKLASH DIFFERENTIAL RING GEAR AND DIFFERENTIAL DRIVE PINION
SST
09564-32011  


26. INSPECT FRONT DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY FRONT


27. INSTALL FRONT DRIVE PINION COMPANION FLANGE FRONT NUT


28. INSTALL DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL


    F044255E01
  1. Using SST and a plastic hammer, install a new oil seal until its surface is flush with the differential carrier end.

    SST
    09608-32010  

  1. Coat the oil seal lip with MP grease.

    Oil seal driven in depth:
    -0.45 to 0.45 mm (-0.0177 to 0.0177 in.)



29. INSTALL FRONT DIFFERENTIAL TUBE ASSEMBLY


    F044256E01
  1. Remove any old FIPG material and be careful not to drop oil on the contact surfaces of the differential and clutch case.

  1. Clean the contact surfaces of any residual FIPG material using gasoline or alcohol.

  1. Apply FIPG to the differential, as shown.

    FIPG:
    Part No. 08826-00090, THREE BOND 1281 or equivalent

    HINT:
    Install the differential tube within 10 minutes of applying FIPG.

  1. Install the differential tube into the differential carrier assembly.



    G023134
  1. Clean the threads of the 4 bolts and retainer bolt holes with toluene or trichloroethylene.

  1. Apply adhesive to 2 to 3 threads of each bolt end.

    Adhesive:
    Part No. 08833-00070, THREE BOND 1324 or equivalent

  1. Install the 4 bolts.

    Torque:
    110 N*m{ 1,122 kgf*cm , 81 ft.*lbf } or less