Home › DRIVE LINE ยท DIFFERENTIAL › DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL (for 4WD)

DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL (for 4WD) > REMOVAL

for Preparation Click here



1. REMOVE FRONT WHEEL


2. REMOVE ENGINE UNDER COVER ASSEMBLY REAR
  1. Remove the 6 bolts and engine under cover assembly rear.



3. REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY
  1. Remove the 4 bolts and No. 1 engine under cover sub-assembly.



4. DRAIN DIFFERENTIAL OIL


    D025304E03
  1. Stop the vehicle on a level place.

  1. Remove the differential filler plug and gasket.

  1. Check that the oil level is within 5mm (0 to 0.20 in.) of the bottom of the filler plug opening.

    NOTICE:
    1. Excessively large or small quantities of oil may cause problems.
    2. After replacing the oil, drive the vehicle and check the oil level again.

    HINT:
    If necessary, fill the rear differential carrier assembly with hypoid gear oil.

    Oil grade:
    Hypoid gear oil API GL-5
    Recommended viscosity:
    Above -18°C (0°F) SAE 90
    Below -18°C (0°F) SAE 80W or 80W-90

    Capacity:
    Front differential carrier assembly:
    1.35 to 1.45 litters
    (1.43 to 1.53 US qts, 1.19 to 1.27 lmp. qts)
    Rear differential carrier assembly
    3.00 to 3.10 litters
    (3.17 to 3.27 US qts, 2.64 to 2.72 lmp. qts)

  1. Check for oil leakage if the oil level is low.

  1. Install the differential filler plug and a new gasket.

    Torque:
    Front differential carrier assembly:
    39 N*m{ 398 kgf*cm , 29 ft.*lbf }
    Rear differential carrier assembly:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }



5. REMOVE FRONT AXLE HUB LH NUT


    F042732
  1. Remove the cotter pin and a lock cap.

  1. Remove the front axle hub nut.



6. SEPARATE FRONT SPEED SENSOR LH


    F044160
  1. Disconnect the speed sensor connector.



    F043112
  1. Using a hexagon wrench (5 mm), remove the bolt and front speed sensor from the steering knuckle.

    SST
    99999-60011  

    NOTICE:
    1. Do not stick and foreign matter on the sensor tip.
    2. Do not let the foreign matter into the sensor installation hole.



7. SEPARATE TIE ROD END SUB-ASSEMBLY LH


    F042735E01
  1. Remove the cotter pin and nut.

  1. Using SST, separate the tie rod end from the steering knuckle arm.

    SST
    09628-62011  



8. SEPARATE NO. 1 FRONT SUSPENSION ARM SUB-ASSEMBLY LOWER LH


    G020159
  1. Remove the 2 bolts, and separate the front lower ball joint attachment LH from the front axle.



    G020160E03
  1. Place matchmarks on the camber adjust cam No. 2 and toe adjust cam sub-assembly.

  1. Remove the nut, camber adjust cam No. 2, camber adjust cam assembly, bolt, toe adjust cam sub-assembly, toe adjust plate No. 2 and front suspension arm sub-assembly lower No. 1 LH.



    G020416E02
  1. Remove the cotter pin and the nut.

  1. Using SST, remove the front lower ball joint attachment LH.

    SST
    09628-00011  



9. REMOVE FRONT DRIVE SHAFT ASSEMBLY LH


F042739E01
  1. Using SST, remove the front drive shaft.

    SST
    09520-01010  
    09520-24010   (09520-32040)

    NOTICE:
    Be careful not to damage the oil seal.



10. REMOVE DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL


    C097017E02
  1. Using SST, remove the oil seal.

    SST
    09308-00010