Home › DRIVE LINE ยท DIFFERENTIAL › REAR DIFFERENTIAL CARRIER ASSEMBLY

REAR DIFFERENTIAL CARRIER ASSEMBLY > DISASSEMBLY

for Preparation Click here



1. REMOVE REAR DIFFERENTIAL CARRIER GASKET


2. FIX REAR DIFFERENTIAL CARRIER ASSEMBLY


3. INSPECT RUNOUT OF REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY REAR


    F001237E03
  1. Using a dial indicator, measure the runout of the companion flange vertically and horizontally.

    Maximum runout:
    Vertical runout: 0.10 mm (0.0039 in.)
    Lateral runout: 0.10 mm (0.0039 in.)

    If the runouts are not with the specifications, replace the companion flange.



4. INSPECT RUNOUT OF DIFFERENTIAL RING GEAR


    C014075
  1. Using a dial indicator, check the runout of the ring gear.

    Maximum runout:
    0.07 mm (0.0028 in.)

    If the runout is greater than the maximum, replace the ring gear with a new one.



5. INSPECT DIFFERENTIAL RING GEAR BACKLASH


    C028211
  1. Using a dial indicator, check the backlash of the ring gear.

    Backlash:
    0.13 to 0.18 mm (0.0051 to 0.0071 in.)

    If the backlash is not within the specification, adjust or repair the side bearing preload as necessary.



6. INSPECT DIFFERENTIAL DRIVE PINION PRELOAD


    C003092
  1. Using a torque wrench, measure the preload of the backlash between the drive pinion and ring gear.

    Preload (at starting):
    0.56 to 0.85 N*m (5.7 to 8.7 kgf*cm, 5.0 to 7.5 in.*lbf)

    If necessary, disassemble and inspect the differential assembly.

    HINT:
    Before measurement, rotate the ring gear 5 times or more.



7. INSPECT TOTAL PRELOAD


    C003092
  1. Using a torque wrench, measure the total preload with the teeth of the drive pinion and ring gear in contact.

    Total preload (at starting):
    Drive pinion preload plus 0.39 to 0.59 N*m (4.0 to 6.0 kgf*cm, 3.5 to 5.2 in.*lbf)

    If necessary, disassemble and inspect the differential.



8. REMOVE REAR DRIVE PINION NUT


    F044346E02
  1. 2WD drive type:
    Using a "Torx" socket (E10), remove the 4 stud bolts.

  1. Using SST and a hammer, unstake nut.

    SST
    09930-00010  



    SA02349E06
  1. Using SST to hold the drive pinion companion flange, remove the nut.

    SST
    09330-00021   (09330-00030)



9. REMOVE REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY REAR


    F052175E02
  1. Using SST, remove the drive pinion companion flange.

    SST
    09950-30012   (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03030)



10. REMOVE REAR DIFFERENTIAL CARRIER OIL SEAL


    SA02348E03
  1. Using SST, remove the oil seal from the differential carrier.

    SST
    09308-10010  



11. REMOVE REAR DIFFERENTIAL DRIVE PINION OIL SLINGER


12. REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING


    Z000641E04
  1. Using SST, remove the front bearing from the drive pinion.

    SST
    09556-22010  



13. REMOVE REAR DIFFERENTIAL BEARING ADJUSTING NUT LOCK


    C030538
  1. Remove the 2 bolts and 2 rear differential bearing adjusting nut locks.



14. REMOVE DIFFERENTIAL CASE ASSEMBLY


    C030539E03
  1. Place matchmarks on the bearing cap and differential carrier.

  1. Remove the 4 bolts and 2 differential bearing caps.

  1. Remove the 2 adjusting nuts.



    C028220
  1. Remove the rear differential case assembly and 2 bearing outer races from the differential carrier assembly.

    HINT:
    Tag the 2 bearings outer races to show the locations for reassembly.



15. REMOVE DIFFERENTIAL DRIVE PINION


    C030540
  1. Remove the differential drive pinion and bearing spacer from the differential carrier assembly.



16. REMOVE REAR DRIVE PINION REAR TAPERED ROLLER BEARING


    R010668E02
  1. Using SST and a press, remove the rear bearing from the drive pinion.

    SST
    09950-00020  

    HINT:
    If either the drive pinion or ring gear is damaged, replace them as a set.



17. REMOVE REAR DIFFERENTIAL DRIVE PINION PLATE WASHER
  1. Remove the plate washer from the drive pinion.



18. REMOVE FRONT BEARING OUTER RACE


    C091046
  1. Using a brass bar an a hammer, remove the front bearing outer race from the differential carrier assembly.



19. REMOVE DIFFERENTIAL OIL STORAGE RING
  1. Using a brass bar and a hammer, remove the oil storage ring.



20. REMOVE REAR BEARING OUTER RACE


    C091047
  1. Using a brass bar and a hammer, remove the rear tapered roller bearing from the carrier.



21. REMOVE DIFFERENTIAL RING GEAR


    W001777E01
  1. Place matchmarks on the ring gear and differential case assembly.

  1. Using a screwdriver and a hammer, unstake the 5 lock plates.

  1. Remove the 10 ring gear set bolts and 5 lock plates.

  1. Using a plastic hammer, tap on the ring gear to separate it from the differential case assembly.



22. INSPECT DIFFERENTIAL CASE ASSEMBLY RUNOUT

HINT:
It will be done only when it exceeds the limit at the ring gear runout check.



    C015154
  1. Install the differential case assembly to the differential carrier assembly.

  1. Align the matchmarks, install the 2 bearing caps with the 4 bolts to the differential carrier assembly.

    Torque:
    85 N*m{ 867 kgf*cm , 63 ft.*lbf }

  1. Inspect the differential case runout.

    Maximum runout:
    0.07 mm (0.0028 in.)

  1. Remove the 4 bolts and bearing caps from the differential carrier assembly.

  1. Remove the differential case assembly from the differential carrier assembly.



23. REMOVE REAR DIFFERENTIAL CASE BEARING


    W002838E01
  1. Using SST, remove the 2 rear differential case bearings from the differential case assembly.

    SST
    09950-40011   (09951-04010, 09952-04010, 09953-04020, 09954-04010, 09955-04061, 09957-04010, 09958-04011)
    09950-60010   (09951-00480)
    09950-60020   (09951-00730)

    HINT:
    Fix the claws of SST to the notches in the differential case assembly.



24. REMOVE REAR DIFFERENTIAL DUST DEFLECTOR


    F040564E10
  1. Using SST and a press, remove the dust deflector.

    SST
    09950-60010   (09951-00380)
    09950-70010   (09951-07150)
    09950-00020  



25. DISASSEMBLE DIFFERENTIAL CASE


    R014029E01
  1. Place matchmarks on the LH and RH cases.

  1. Remove the 8 bolts uniformly, a little at a time.

  1. Using a plastic hammer, separate the LH and RH cases.



    C090324E02
  1. Remove these parts from the differential case.
    A (2 pieces)
    Side gear
    B (2 pieces)
    Side gear thrust washer
    C
    Spider
    D (4 pieces)
    Pinion gear
    E (4 pieces)
    Pinion gear thrust washer



26. INSPECT DIFFERENTIAL PINION AND SIDE GEAR
  1. Check that there is no damage to the differential pinion and differential side gear.
    If the differential pinion and/or differential side gear is damaged, replace the differential.