Home › DRIVE LINE ยท DIFFERENTIAL › REAR DIFFERENTIAL CARRIER OIL SEAL

REAR DIFFERENTIAL CARRIER OIL SEAL > INSTALLATION

for Preparation Click here



1. INSTALL REAR DIFFERENTIAL DRIVE PINION BEARING SPACER
  1. Install a new rear differential drive pinion bearing spacer.



2. INSTALL REAR DRIVE PINION FRONT TAPERED ROLLER BEARING
  1. Using a brass bar and a hammer, install a new oil storage ring.

  1. Using SST and a hammer, install the front bearing outer race.

  1. Install the front bearing.

    SST
    09316-60011   (09316-00011, 09316-00021)



3. INSTALL REAR DIFFERENTIAL DRIVE PINION OIL SLINGER


4. INSTALL REAR DIFFERENTIAL CARRIER OIL SEAL


    F040719E02
  1. Using SST and a hammer, install a new oil seal.

    SST
    09554-30011  

    Oil seal drive in depth:
    0.7 to 1.3 mm (0.0276 to 0.0512 in.)

  1. Coat oil seal lip with MP grease.



5. INSTALL REAR DRIVE COMPANION FLANGE SUB-ASSEMBLY REAR


    F040716E02
  1. Using SST, install the companion flange.

    SST
    09950-30012   (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03030)

  1. Coat the threads of a new nut with hypoid gear oil LSD.



    C088916E02
  1. Using SST to hold the companion flange, tighten the nut.

    SST
    09330-00021   (09330-00030)

    Torque:
    215 N*m{ 2,190 kgf*cm , 159 ft.*lbf }



6. INSPECT DIFFERENTIAL DRIVE PINION PRELOAD


    C089308
  1. Using a torque wrench, measure the preload of the backlash between the drive pinion and ring rear.

    New bearing:
    1.05 to 1.64 N*m (10.7 to 16.7 kgf*cm, 9.3 to 14.5 in.*lbf)

    Reused bearing:
    0.56 to 0.85 N*m (5.7 to 8.7 kgf*cm, 5.0 to 7.5 in.*lbf)

    If necessary, disassemble and inspect the differential assembly.



7. INSTALL REAR DRIVE PINION NUT


    C089310
  1. Using a chisel and a hammer, stake the nut.



8. INSTALL PROPELLER SHAFT ASSEMBLY


    C060588E02
  1. Align the matchmarks on the propeller shaft differential flange.

  1. 2WD Drive Type:
    Install the propeller shaft with the 4 washers and 4 nuts.

    Torque:
    88 N*m{ 897 kgf*cm , 65 ft.*lbf }

  1. 4WD Drive Type:
    Install the propeller shaft with the 4 bolts, 4 washers and 4 nuts.

    Torque:
    88 N*m{ 897 kgf*cm , 65 ft.*lbf }



9. FILL UP DIFFERENTIAL OIL


    D025304E03
  1. Stop the vehicle on a level place.

  1. Remove the differential filler plug and gasket.

  1. Check that the oil level is within 5mm (0 to 0.20 in.) of the bottom of the filler plug opening.

    NOTICE:
    1. Excessively large or small quantities of oil may cause problems.
    2. After replacing the oil, drive the vehicle and check the oil level again.

    HINT:
    If necessary, fill the rear differential carrier assembly with hypoid gear oil.

    Oil grade:
    Hypoid gear oil API GL-5
    Recommended viscosity:
    Above -18°C (0°F) SAE 90
    Below -18°C (0°F) SAE 80W or 80W-90

    Capacity:
    Front differential carrier assembly:
    1.35 to 1.45 litters
    (1.43 to 1.53 US qts, 1.19 to 1.27 lmp. qts)
    Rear differential carrier assembly
    3.00 to 3.10 litters
    (3.17 to 3.27 US qts, 2.64 to 2.72 lmp. qts)

  1. Check for oil leakage if the oil level is low.

  1. Install the differential filler plug and a new gasket.

    Torque:
    Front differential carrier assembly:
    39 N*m{ 398 kgf*cm , 29 ft.*lbf }
    Rear differential carrier assembly:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }



10. INSPECT DIFFERENTIAL OIL


    D025304E03
  1. Stop the vehicle on a level place.

  1. Remove the differential filler plug and gasket.

  1. Check that the oil level is within 5mm (0 to 0.20 in.) of the bottom of the filler plug opening.

    NOTICE:
    1. Excessively large or small quantities of oil may cause problems.
    2. After replacing the oil, drive the vehicle and check the oil level again.

    HINT:
    If necessary, fill the rear differential carrier assembly with hypoid gear oil.

    Oil grade:
    Hypoid gear oil API GL-5
    Recommended viscosity:
    Above -18°C (0°F) SAE 90
    Below -18°C (0°F) SAE 80W or 80W-90

    Capacity:
    Front differential carrier assembly:
    1.35 to 1.45 litters
    (1.43 to 1.53 US qts, 1.19 to 1.27 lmp. qts)
    Rear differential carrier assembly
    3.00 to 3.10 litters
    (3.17 to 3.27 US qts, 2.64 to 2.72 lmp. qts)

  1. Check for oil leakage if the oil level is low.

  1. Install the differential filler plug and a new gasket.

    Torque:
    Front differential carrier assembly:
    39 N*m{ 398 kgf*cm , 29 ft.*lbf }
    Rear differential carrier assembly:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }