Home › DRIVE LINE ยท VF4AM TRANSFER › TOUCH SELECT 2-4 AND HIGH-LOW SYSTEM

TOUCH SELECT 2-4 AND HIGH-LOW SYSTEM > INSPECTION

for Preparation Click here


NOTICE:
  1. H4 to L4: Stop the vehicle and apply brake, then shift the transmission shift lever into "N" position first.
  2. Do not operate the four wheel drive control switch and the differential lock switch at the same time.
  3. Do not change from 2WD to 4WD when the vehicle speed is 100 km/h or more.



1. INSPECT H2 (2WD) TO H4 (4WD AND DIFFERENTIAL LOCK "FREE") SHIFT


    F044403
  1. Start the engine, and the differential lock switch is in "OFF" position.

  1. Turn the four wheel drive control switch from the "H2" position to the "H4" position.

  1. Check that the 4WD indicator light comes on after it is blinking. (The center diff. lock indicator blinks while shifting.)

  1. Turn the four wheel drive control switch from the "H4" position to the "H2" position. (The center diff. lock indicator blinks while shifting.)

  1. Check that the 4WD indicator light goes off after it is blinking.



2. INSPECT H4 (4WD AND DIFFERENTIAL LOCK "LOCK") TO H2 (2WD) SHIFT


    F044404
  1. Start the engine, and differential lock switch is in "OFF" position.

  1. Check that the center diff. lock indicator light comes on after pressing the differential lock switch for 2 seconds.

  1. Turn the four wheel drive control switch from the "H4" position to the "H2" position.

  1. Check that the 4WD indicator light and center diff. lock indicator light goes off after those are blinking.



3. INSPECT H4 (4WD AND DIFFERENTIAL LOCK "FREE") TO H4 (4WD AND DIFFERENTIAL LOCK "LOCK") SHIFT


    F044034
  1. Start the engine, and the differential lock switch is in "OFF" position.

  1. Turn the four wheel drive control switch to "H4" position while pressing it.

  1. Check that the center diff. lock indicator light comes on after pressing the differential lock switch for 2 seconds. Check that the center diff. lock indicator light goes off after pressing the differential lock switch for 2 seconds.



4. INSPECT L4 (4WD AND DIFFERENTIAL LOCK "FREE") TO L4 (4WD AND DIFFERENTIAL LOCK "LOCK") SHIFT


    F044035
  1. Start the engine, and differential lock switch is in "OFF" position.

  1. Turn the four wheel drive control switch to "L4" position while pressing it.

  1. Check that the 4LO indicator light comes on after it is blinking.

  1. Check that the center diff. lock indicator light comes on after pressing the differential lock switch for 2 seconds. Check that the center diff. lock indicator light goes off after pressing the differential lock switch for 2 seconds.



5. INSPECT H4 (4WD AND DIFFERENTIAL LOCK "FREE") TO L4 (4WD AND DIFFERENTIAL LOCK "FREE") SHIFT


    F044036
  1. Start the engine, and differential lock switch is in "OFF" position.

  1. Turn the four wheel drive control switch from the "H4" position to the "L4" position while pressing it.

  1. Check that the 4LO indicator light comes on after it is blinking.

  1. Turn the four wheel drive control switch from the "L4" position to the "H4" position while pressing it.

  1. Check that the 4LO indicator light goes off after it is blinking.



6. INSPECT H4 (4WD AND DIFFERENTIAL LOCK "LOCK") TO L4 (4WD AND DIFFERENTIAL LOCK "LOCK") SHIFT


    F044037
  1. Start the engine, and differential lock switch is in "OFF" position.

  1. Check that the center diff. lock indicator light comes on after pressing the differential lock switch for 2 seconds.

  1. Turn the four wheel drive control switch from the "H4" position to the "L4" position while pressing it.

  1. Check that the 4LO indicator light comes on after it is blinking.

  1. Turn the four wheel drive control switch from the "L4" position to the "H4" position while pressing it.

  1. Check that the 4LO indicator light goes off after it is blinking.



7. INSPECT H2 (2WD) TO L4 (4WD AND DIFFERENTIAL LOCK "FREE") SHIFT


    F044405
  1. Start the engine, and differential lock switch is in "OFF" position.

  1. Turn the four wheel drive control switch from the "H2" position to the "H4" position.

  1. Check that the 4WD indicator light comes on after it is blinking. (The center diff. lock indicator blinks while shifting.)

  1. Turn the four wheel drive control switch from the "H4" position to the "L4" position while pressing it.

  1. Check that the 4LO indicator light comes on after it is blinking.



8. INSPECT L4 (4WD AND DIFFERENTIAL LOCK "FREE") TO H2 (2WD) SHIFT


    F044406
  1. Start the engine, and differential lock switch is in "OFF" position.

  1. Turn the four wheel drive control switch from the "L4" position to the "H4" position while pressing it.

  1. Check that the 4LO indicator light goes off after it is blinking.

  1. Turn the four wheel drive control switch from the "H4" position to the "H2" position.

  1. Check that the 4WD indicator light goes off after it is blinking. (The center diff. lock indicator blinks while shifting.)



9. INSPECT L4 (4WD AND DIFFERENTIAL LOCK "LOCK") TO H2 (2WD) SHIFT


    F044407
  1. Start the engine, and differential lock switch is in "OFF" position.

  1. Check that the center diff. lock indicator light comes on after pressing the differential lock switch for 2 seconds.

  1. Turn the four wheel drive control switch from the "L4" position to the "H4" position while pressing it.

  1. Check that the 4LO indicator light goes off after it is blinking.

  1. Turn the four wheel drive control switch from the "H4" position to the "H2" position.

  1. Check that the 4WD indicator light and center diff. lock indicator light goes off after those are blinking.



10. INSPECT DIFFERENTIAL LOCK SWITCH


    F044040E01
  1. Remove the instrument panel finish lower panel sub-assembly.

  1. Remove the differential lock switch from the instrument panel finish lower sub-assembly.

  1. Inspect the continuity between the each terminal.
    Switch position
    Tester connection
    Specified condition
    OFF
    +B (3) to GND (4)
    No continuity
    Hold ON
    +B (3) to GND (4)
    Continuity
    Illumination
    ILL+ (1) to ILL- (2)
    Continuity
    If continuity is not as specified, replace the differential lock switch or bulb.



11. INSPECT FOUR WHEEL DRIVE CONTROL SWITCH


    F044039E03
  1. Remove the center instrument cluster finish panel sub-assembly.

  1. Remove the four wheel drive control switch from the center instrument cluster finish panel sub-assembly.

  1. Inspect the continuity between the each terminals.
    Switch position
    Tester connection
    Specified condition
    H2
    2-4 (5) to GND (4)
    Continuity
    H4
    2-4 (5) to GND (4)
    Continuity
    2-4 (5) to GND (4)
    No continuity
    LO (2) to GND (4)
    Continuity
    LO (2) to GND (4)
    No continuity
    L4
    LO (2) to GND (4)
    Continuity
    Illumination
    ILL+ (1) to ILL- (3)
    Continuity
    If continuity is not as specified, replace the four wheel drive control switch or bulb.



12. INSPECT ACTUATOR

NOTICE:
Inspection for the actuator must be done with the actuator installed on the transfer assembly.

  1. Turn the ignition switch to ON.

  1. Check the operating sound produced by four wheel drive control switch operation and the differential lock switch operation.
    If the operating sound cannot be heard, check the four wheel control ECU and the wire harness in the next step. When the wire harness and four wheel drive control ECU is normal, replace the actuator.



13. INSPECT WIRE HARNESS


    F044038E01
  1. Disconnect the cable from the negative battery terminal or remove the 20A 4WD fuse.

    CAUTION:
    Failure to disconnect power for the 4WD ECU may cause the transfer case actuator to be activated, resulting in damage to the transfer case actuator.

  1. Disconnect the actuator connector and four wheel drive control ECU connector.

  1. Check continuity on the wire harness between four wheel drive control ECU and the actuator.
    Tester connection
    Specified condition
    TM1 (F10-2) - TM1 (T3-2)
    Continuity
    TM2 (F10-5) - TM2 (T3-1)
    Continuity
    TL2 (F10-24) - TL2 (T3-4)
    Continuity
    TL3 (F10-23) - TL3 (T3-5)
    Continuity
    HM2 (F10-4) - HM2 (T3-7)
    Continuity
    HM1 (F10-1) - HM1 (T3-8)
    Continuity
    P1 (F10-22) - CDL (T3-9)
    Continuity
    HL2 (F10-26) - HL2 (T3-11)
    Continuity
    HL1 (F10-17) - HL1 (T3-12)
    Continuity
    If continuity is not as specified, repair or replace the wire harness.



14. INSPECT FOUR WHEEL DRIVE CONTROL ECU
  1. Connect the wire harness side connector to the four wheel drive control ECU.

  1. Connect the cable to the negative battery terminal or install the 20A 4WD fuse.



  1. Inspect the wire harness side connector from the back side, as shown below.


    C134067E01


    STANDARD VALUE OF ECU TERMINAL:

    Terminals (Symbols)
    Condition
    STD Voltage (V)
    F10-1 (HM1) - F10-4 (HM2)
    1. Ignition switch ON
    2. Four wheel drive control switch "H4" position → Four wheel drive control switch "L4" position
    10 - 14 to 2 or less
    or
    0 (0.5 s) - 14 (50 ms)
    pulse generation
    F10-4 (HM2) - F10-1 (HM1)
    1. Ignition switch ON
    2. Four wheel drive control switch "L4" position → Four wheel drive control switch "H4" position
    F10-2 (TM1) - F10-5 (TM2)
    1. Ignition switch ON
    2. Differential lock switch is in "OFF" position
    3. Four wheel drive control switch "H2" position → Four wheel drive control switch "H4" position
    10 - 14 to 2 or less
    or
    0 (0.5 s) - 14 (50 ms)
    pulse generation
    F10-5 (TM2) - F10-2 (TM1)
    1. Ignition switch ON
    2. Keep pressing the differential lock switch approx. 2 seconds to turn it ON
    3. Four wheel drive control switch "H4" position or "L4" position → Four wheel drive control switch "H2" position
    F10-3 (DM1) - F10-6 (DM2)
    1. Ignition switch ON
    2. A.D.D. FREE → A.D.D. LOCK
    10 - 14 to 2 or less
    or
    0 (0.5 s) - 14 (50 ms)
    pulse generation
    F10-6 (DM2) - F10-3 (DM1)
    1. Ignition switch ON
    2. A.D.D. LOCK → A.D.D. FREE
    F10-4 (HM2) - F9-1 (GND)
    1. Ignition switch ON
    2. Four wheel drive control switch "H4" position → Four wheel drive control switch "L4" position
    2 or less to 10 - 14
    F9-1 (GND) - Body ground
    1. Ignition switch OFF
    Continuity
    F9-6 (IG) - F9-1 (GND)
    1. Ignition switch ON
    10 - 14
    F10-12 (DL2) - F9-1 (GND)
    1. Ignition switch ON
    2. A.D.D. LOCK → A.D.D. FREE
    2 or less to 10 - 14
    F10-13 (DL1) - F9-1 (GND)
    1. Ignition switch ON
    2. A.D.D. FREE → A.D.D. LOCK
    2 or less to 10 - 14
    F10-17 (HL1) - F9-1 (GND)
    1. Ignition switch ON
    2. Four wheel drive control switch "H4" position → Four wheel drive control switch "L4" position
    10 - 14 to 2 or less
    F9-8 (2-4) - F9-1 (GND)
    1. Ignition switch ON
    2. Four wheel drive control switch "L4" position → Four wheel drive control switch "H22" position or "H4" position
    10 - 14 to 2 or less
    F9-9 (SPD) - F9-1 (GND)
    1. During driving
    Pulse generation
    F9-11 (IND3) - F9-1 (GND)
    1. Ignition switch ON
    2. Four wheel drive control switch "H2" position → Four wheel drive control switch "L4" position
    10 - 14 to 0 - 3.5
    F9-15 (LO) - F9-1 (GND)
    1. Ignition switch ON
    2. Four wheel drive control switch "H2" position → Four wheel drive control switch "L4" position
    10 - 14 to 2 or less
    F9-16 (DL) - F9-1 (GND)
    1. Ignition switch ON
    2. Differential lock switch is in "OFF" position → Keep pressing the differential lock switch approx. 2 seconds to turn it ON
    10 - 14 to 2 or less
    F10-18 (ADD) - F9-1 (GND)
    1. Ignition switch ON
    2. A.D.D. FREE → A.D.D. LOCK
    10 - 14 to 2 or less
    F10-23 (TL3) - F9-1 (GND)
    1. Ignition switch ON
    2. Four wheel drive control switch "H2" position → Four wheel drive control switch "L4" position
    3. Differential lock switch is in "OFF" position → Keep pressing the differential lock switch approx. 2 seconds to turn it ON
    2 or less to 10 - 14
    F10-24 (TL2) - F9-1 (GND)
    1. Ignition switch ON
    2. Four wheel drive control switch "H2" position → Four wheel drive control switch "L4" position
    3. Differential lock switch is in "OFF" position → Keep pressing the differential lock switch approx. 2 seconds to turn it ON
    10 - 14 to 2 or less
    F10-25 (TL1) - F9-1 (GND)
    1. Ignition switch ON
    2. Four wheel drive control switch "H2" position → Four wheel drive control switch "L4" position
    3. Differential lock switch is in "OFF" position → "ON" position
    2 or less to 10 - 14
    F10-26 (HL2) - F9-1 (GND)
    1. Ignition switch ON
    2. Four wheel drive control switch "H4"position → Four wheel drive control switch "L4" position
    2 or less to 10 - 14
    F9-19 (IND1) - F9-1 (GND)
    1. Ignition switch ON
    2. Four wheel drive control switch "H2" position → Four wheel drive control switch "H4" position or "L4" position
    10 - 14 to 2 or less
    F9-20 (IND2) - F9-1 (GND)
    1. Ignition switch ON
    2. Differential lock switch is in "OFF" position → Keep pressing the differential lock switch approx. 2 seconds to turn it ON
    10 - 14 to 2 or less
    F9-22 (N) - F9-1 (GND)
    1. Ignition switch ON
    2. Transmission shift lever other position → Transmission shift lever N position
    2 or less to 10 - 14
    F9-24 (L4) - F9-1 (GND)
    1. Ignition switch ON
    2. Four wheel drive control switch "H4" position → Four wheel drive control switch "L4" position
    10 - 14 to 2 or less