Home › DRIVE LINE ยท VF4BM TRANSFER › TRANSFER ASSEMBLY

TRANSFER ASSEMBLY > DISASSEMBLY

for Preparation Click here



1. REMOVE HOSE


2. TEST TRANSFER RH BEARING RETAINER SUB-ASSEMBLY


    F043427
  1. Remove the 5 bolts and front bearing retainer sub-assembly.

    HINT:
    If necessary, tap the front bearing retainer sub-assembly with a plastic hammer to remove it.



3. REMOVE TRANSFER COVER TYPE T OIL SEAL
  1. Using a screwdriver and hammer, remove the oil seal from the front bearing retainer sub-assembly.



4. REMOVE TRANSFER CASE COVER SUB-ASSEMBLY


    F043428
  1. Remove the 4 bolts and the case cover sub-assembly.



5. REMOVE BREATHER OIL DEFLECTOR SUB-ASSEMBLY


6. REMOVE OUTPUT SHAFT COMPANION FLANGE SUB-ASSEMBLY


    F043429E01
  1. Using a chisel and hammer, loosen the staked part of the output shaft companion flange lock nut.

  1. Using SST to hold the output shaft companion flange, remove the output shaft companion flange lock nut.

    SST
    09330-00021  



    F043430E01
  1. Using SST, remove the output shaft companion flange sub-assembly.

    SST
    09950-40011   (09951-04020, 09952-04010, 09953-04030, 09954-04010, 09955-04051, 09957-04010, 09958-04011)



7. REMOVE TRANSFER OUTPUT SHAFT COMPANION FLANGE OIL SEAL
  1. Using a screwdriver and hammer, remove the companion flange oil seal from the output shaft companion flange sub-assembly.



8. REMOVE OUTPUT SHAFT COMPANION FLANGE SUB-ASSEMBLY
  1. Remove the rear output shaft companion flange sub-assembly using the same procedure as for the front output shaft companion flange sub-assembly.

    SST
    09330-00021  
    09950-40011   (09951-04020, 09952-04010, 09953-04030, 09954-04010, 09955-04051, 09957-04010, 09958-04011)



9. REMOVE TRANSFER OUTPUT SHAFT COMPANION FLANGE OIL SEAL
  1. Using a screwdriver and hammer, remove the companion flange oil seal from the output shaft companion flange sub-assembly.



10. REMOVE FRONT TRANSFER EXTENSION HOUSING SUB-ASSEMBLY


    F043431
  1. Remove the 5 bolts and extension housing sub-assembly.

    HINT:
    If necessary, tap the extension housing sub-assembly with a plastic hammer to remove it.



11. REMOVE TRANSFER EXTENSION HOUSING TYPE T OIL SEAL


    F043432
  1. Using a screwdriver and hammer, remove the extension housing type T oil seal.



12. REMOVE TRANSFER OUTPUT WASHER


13. REMOVE COLLAR


14. REMOVE TRANSFER REAR CASE


    F043433
  1. Remove the 12 bolts and clamp.

  1. Remove the transfer rear case.

    HINT:
    If necessary, tap the transfer rear case with a plastic hammer to remove it.



15. REMOVE NO. 2 TRANSFER GEAR SHIFT FORK WITH TRANSFER HIGH AND LOW CLUTCH SLEEVE


    F043434
  1. Remove the bolt, gear shift fork No. 2 and high and low clutch sleeve.



16. REMOVE CTR DIFFERENTIAL LOCK FORK SUB-ASSEMBLY WITH FRONT DRIVE CLUTCH SLEEVE


    F043502
  1. Using 2 screwdrivers and hammer, tap out the snap ring.



    F043503
  1. Remove the bolt, CTR differential lock fork sub-assembly and front drive clutch sleeve.



17. REMOVE REAR OUTPUT SHAFT SUB-ASSEMBLY, FRONT DRIVE CHAIN AND DRIVEN SPROCKET SUB-ASSEMBLY


    F043504
  1. Mount the transfer case rear in a vise.

  1. Using a plastic hammer, carefully tap the a transfer case rear, and remove the rear output shaft sub assembly together with front drive chain and driven sprocket sub-assembly.



    F043505
  1. Remove the rear output shaft sub-assembly, front drive chain and driven sprocket sub assembly.



18. REMOVE TRANSFER DRIVEN SPROCKET BEARING


    F043523
  1. Using a press, remove the driven sprocket bearing.



19. REMOVE TRANSFER INPUT GEAR RADIAL BALL BEARING


    F043524E02
  1. Using SST, a press and steel bar, remove the transfer input gear radial ball bearing.

    SST
    09555-55010  



20. REMOVE TRANSFER SHIFT ACTUATOR ASSEMBLY


    F043506
  1. Using 2 screwdrivers and a hammer, tap out the 2 snap rings.



    F043445
  1. Remove the 3 bolts and transfer shift actuator assembly.



21. REMOVE TRANSFER CASE NO.1 PLUG
  1. Remove the transfer case No. 1 plug (filler plug) and gasket.



22. REMOVE TRANSFER CASE NO.1 PLUG
  1. Remove the transfer case No. 1 plug (drain plug) and gasket.



23. REMOVE TRANSFER OIL SEPARATOR SUB-ASSEMBLY


    F043446
  1. Remove the 3 bolts and oil separator sub-assembly.



24. REMOVE TRANSFER CASE MAGNET


25. REMOVE TRANSFER OIL PUMP BODY SUB-ASSEMBLY


    F043447
  1. Remove the 3 bolts and oil pump body sub-assembly.



26. REMOVE TRANSFER OIL PUMP BODY O-RING


    F043462
  1. Using a screwdriver, remove the oil pump body O-ring.



27. REMOVE TRANSFER OIL PUMP GEAR


    F043448
  1. Remove the transfer oil pump gear.



28. REMOVE LOW PLANETARY GEAR ASSEMBLY WITH INPUT SHAFT SUB-ASSEMBLY


    F043449
  1. Using a snap ring expander, remove the snap ring.



    Q007221
  1. Remove the low planetary gear assembly with input shaft assembly.



29. REMOVE TRANSFER OUTPUT SHAFT SPACER


    F043451
  1. Remove the transfer output shaft spacer.



30. REMOVE TRANSFER OUTPUT SHAFT FRONT NEEDLE ROLLER BEARING


31. REMOVE TRANSFER CASE OIL SEAL
  1. Using a screwdriver and hammer, remove the transfer case oil seal.



32. REMOVE TRANSFER INPUT GEAR STOPPER SHAFT SNAP RING


    F043452
  1. Using a snap ring expander, remove the input gear stopper shaft snap ring.



33. REMOVE TRANSFER INPUT GEAR STOPPER


    F043453
  1. Remove the transfer input gear stopper.



34. REMOVE TRANSFER INPUT GEAR STOPPER BALL


35. REMOVE MANUAL TRANSFER PLANETARY CARRIER WASHER


36. REMOVE TRANSFER INPUT SHAFT


    F043454E01
  1. Remove the transfer input shaft.



37. REMOVE TRANSFER NO. 1 THRUST BEARING RACE


38. REMOVE TRANSFER LOW PLANETARY GEAR BEARING


39. REMOVE TRANSFER NO. 1 INPUT SHAFT SEAL RING


    F043525E01
  1. Remove the 2 seal rings.



40. INSPECT TRANSFER INPUT SHAFT


    F043458
  1. Using a micrometer, measure the outer diameter of the input shaft journal surface.

    Minimum diameter:
    47.59 mm (1.8736 in.)

    If the outer diameter is less than the minimum, replace the input shaft.



    F043459
  1. Using a dial indicator, measure the inside diameter of the input shaft bushing.

    Maximum diameter:
    48.14 mm (1.8953 in.)

    If the inside diameter exceeds the maximum, replace the input shaft.



41. INSPECT PLANETARY PINION GEAR THRUST CLEARANCE


    F043465
  1. Using a feeler gauge, measure the thrust clearance of the planetary pinion gear.

    Standard clearance:
    0.11 to 0.84 mm (0.0043 to 0.0331 in.)

    Maximum clearance:
    0.84 mm (0.0331 in.)

    If the clearance exceeds the maximum, replace the planetary gear assembly.



42. INSPECT PLANETARY PINION GEAR RADIAL CLEARANCE


    F043466
  1. Using a dial indicator, measure the radial clearance of the planetary pinion gear.

    Standard clearance:
    0.009 to 0.038 mm (0.0004 to 0.0015 in.)

    Maximum clearance:
    0.038 mm (0.0015 in.)

    If the clearance exceeds the maximum, replace the planetary gear assembly.



43. REMOVE TRANSFER INPUT SHAFT BEARING


    F043467E02
  1. Using a snap ring expander, remove the snap ring.

  1. Using SST and a press, remove the input shaft bearing.

    SST
    09554-30011  
    09555-55010  



44. REMOVE TRANSFER LOW PLANETARY GEAR SPLINE PIECE


    F043507
  1. Using a screwdriver, remove the snap ring.

  1. Remove the low planetary gear spline piece.



45. REMOVE TRANSFER LOW PLANETARY GEAR BEARING


    F043526E02
  1. Using SST, remove the low planetary gear bearing.

    SST
    09612-65014   (09612-01030, 09612-01050)

    NOTICE:
    Hang SST securely to the clearance between the bearing and the low planetary gear.



46. INSPECT DRIVE SPROCKET THRUST CLEARANCE


    F044049
  1. Using a feeler gauge, measure the drive sprocket thrust clearance.

    Standard clearance:
    0.15 to 0.24 mm (0.0059 to 0.0094 in.)

    Maximum clearance:
    0.24 mm (0.0094 in.)

    If the clearance exceeds the maximum, replace the drive sprocket.



47. INSPECT DRIVE SPROCKET RADIAL CLEARANCE


    F044050
  1. Using a dial indicator, measure the radial clearance of the drive sprocket.

    Standard clearance:
    0.01 to 0.06 mm (0.0004 to 0.0024 in.)

    Maximum clearance:
    0.06 mm (0.0024 in.)

    If the clearance exceeds the maximum, replace the drive sprocket, output shaft rear or needle roller bearing.



48. REMOVE TRANSFER LOW PLANETARY RING GEAR HOLE SNAP RING


    F044051
  1. Using a snap ring expander, remove the snap ring.



49. REMOVE NO. 2 TRANSFER OUTPUT SHAFT SPACER


50. REMOVE TRANSFER OUTPUT SHAFT SPACER BALL


51. REMOVE CENTER DIFFERENTIAL CASE


52. REMOVE TRANSFER CLUTCH HUB


    F043510
  1. Remove the transfer clutch hub.



53. REMOVE TRANSFER OUTPUT SHAFT FRONT NEEDLE ROLLER BEARING


54. REMOVE TRANSFER OUTPUT SHAFT PLATE WASHER


55. REMOVE TRANSFER OUTPUT SHAFT REAR RADIAL BALL BEARING


    F043475E01
  1. Using SST and a press, remove the output shaft rear radial ball bearing.

    SST
    09555-55010  



56. REMOVE NO. 1 TRANSFER OUTPUT SHAFT SPACER


    F043476
  1. Remove the transfer output shaft spacer.



57. REMOVE TRANSFER DRIVE SPROCKET SUB-ASSEMBLY


58. REMOVE TRANSFER DRIVE SPROCKET BEARING


59. REMOVE TRANSFER OUTPUT SHAFT PLATE WASHER


60. INSPECT TRANSFER OUTPUT SHAFT REAR


    F043511E01
  1. Using a micrometer, measure the outer diameter of the output shaft rear journal surface.

    Standard diameter:
    Part A:
    27.98 to 27.99 mm (1.1016 to 1.1020 in.)
    Part B:
    31.98 to 32.00 mm (1.2591 to 1.2598 in.)
    Part C:
    34.98 to 35.00 mm (1.3772 to 1.3780 in.)
    Part D:
    36.98 to 37.00 mm (1.4559 to 1.4567 in.)

    Minimum diameter:
    Part A:
    27.98 mm (1.1016 in.)
    Part B:
    31.98 mm (1.2591 in.)
    Part C:
    34.98 mm (1.3772 in.)
    Part D:
    36.98 mm (1.4559 in.)

    If the outer diameter is less than the minimum, replace the output shaft rear.



61. INSPECT HIGH AND LOW CLUTCH SLEEVE AND GEAR SHIFT FORK NO. 2 CLEARANCE


    F043481
  1. Using vernier calipers, measure the thickness of the gear shift fork No. 2 claw.

    Thickness:
    10 mm (0.3937 in.)

  1. Using vernier calipers, measure the groove of the high and low clutch sleeve.

    Distance:
    10.5 mm (0.4134 in.)

  1. Calculate a clearance between the high and low clutch sleeve and gear shift fork No. 2 clearance.

    Standard clearance:
    0.26 to 0.84 mm (0.0102 to 0.0331 in)

    Maximum clearance:
    0.84 mm (0.0331 in.)

    If the clearance exceeds the maximum, replace the high and low clutch sleeve or gear shift fork No. 2.



62. INSPECT FRONT DRIVE CLUTCH SLEEVE AND CTR DIFFERENTIAL LOCK FORK SUB-ASSEMBLY CLEARANCE


    F043483
  1. Using vernier calipers, measure the thickness of the CTR differential lock fork clow.

    Thickness:
    10 mm (0.3937 in.)

  1. Using vernier calipers, measure the groove of the front drive clutch sleeve.

    Distance:
    10.5 mm (0.4134 in.)

  1. Calculate a clearance between the front drive clutch sleeve and CTR differential lock fork.

    Standard clearance:
    0.26 to 0.84 mm (0.0102 to 0.0331 in.)

    Maximum clearance:
    0.84 mm (0.0331 in.)

    If the clearance exceeds the maximum, replace the front drive clutch sleeve or CTR differential lock fork.



63. INSPECT CENTER DIFFERENTIAL CASE AND HIGH AND LOW CLUTCH SLEEVE


    F043493
  1. Check that the tip of the spline gear of the front drive clutch sleeve is not worn.

  1. Install the front drive clutch sleeve to the center differential case and check that the front drive clutch sleeve moves smoothly.



64. INSPECT CENTER DIFFERENTIAL CASE AND FRONT DRIVE CLUTCH SLEEVE


    F044398
  1. Check that the tip of the spline gear of the front drive clutch sleeve is not worn.

  1. Install the front drive clutch sleeve to the center differential case and check that the front drive clutch sleeve moves smoothly.



65. REMOVE TRANSFER CASE PLUG


    F043455
  1. Remove the transfer case plug.



66. REMOVE COMPRESSION SPRING


67. REMOVE WITH HEAD PIN


68. REMOVE TRANSFER LOW PLANETARY RING GEAR


    F043456
  1. Using a screwdriver, remove the snap ring.



    F043457E01
  1. Remove the low planetary ring gear from the front case.