Home › DRIVE LINE ยท VF4AM TRANSFER › TRANSFER ASSEMBLY

TRANSFER ASSEMBLY > REASSEMBLY

for Preparation Click here



1. INSTALL TRANSFER LOW PLANETARY RING GEAR
  1. Install the low planetary ring gear to the front case.



    F043456
  1. Using a screwdriver, install the snap ring.



2. INSTALL WITH HEAD PIN


    F043455
  1. Install w/ head pin.



3. INSTALL COMPRESSION SPRING


4. INSTALL TRANSFER CASE PLUG

Torque:
18.6 N*m{ 190 kgf*cm , 14 ft.*lbf }



5. INSTALL TRANSFER OUTPUT SHAFT PLATE WASHER


    F043476
  1. Install the transfer output shaft plate washer.



6. INSTALL TRANSFER DRIVE SPROCKET BEARING


7. INSTALL TRANSFER DRIVE SPROCKET SUB-ASSEMBLY


8. INSTALL NO. 1 TRANSFER OUTPUT SHAFT SPACER


9. INSTALL TRANSFER OUTPUT SHAFT REAR RADIAL BALL BEARING


    F044046E01
  1. Using SST and a press, install a new output shaft rear radial ball bearing.

    SST
    09316-60011   (09316-00011, 09316-00071)

    NOTICE:
    Install the output shaft rear radial ball bearing so that the bearing snap ring groove face to the rear.



10. INSTALL TRANSFER SYNCHRONIZER RING SET


    F043474
  1. Install the synchronizer ring.



11. INSTALL FRONT DRIVE CLUTCH SLEEVE


    F044754
  1. Install front drive clutch sleeve.



12. INSTALL SYNCHROMESH SHIFTING KEY TRANSFER DRIVE


    F044410
  1. Install the3 shifting keys to the clutch hub.



13. INSTALL TRANSFER SYNCHROMESH SHIFTING KEY SPRING
  1. Install the 2 shifting key springs to the clutch hub.

    NOTICE:
    Position the shifting key springs so that their end gaps are not aligned.



14. INSTALL TRANSFER OUTPUT SHAFT PLATE WASHER


    F043472
  1. Install the transfer output shaft plate washer.



15. INSTALL TRANSFER OUTPUT SHAFT FRONT NEEDLE ROLLER BEARING


16. INSTALL TRANSFER CLUTCH HUB


17. INSTALL CENTER DIFFERENTIAL CASE


    F044051
  1. Install the center differential case.



18. INSTALL TRANSFER OUTPUT SHAFT SPACER BALL


19. INSTALL TRANSFER OUTPUT SHAFT SPACER NO.2


20. INSTALL TRANSFER LOW PLANETARY RING GEAR HOLE SNAP RING
  1. Using a snap ring expender, install the snap ring.



21. INSTALL DRIVE SPROCKET RADIAL CLEARANCE


22. INSPECT DRIVE SPROCKET THRUST CLEARANCE


23. INSTALL TRANSFER INPUT SHAFT BEARING


    F043513E01
  1. Using SST and a press, install a new bearing with the groove facing forward.

    SST
    09223-15020  
    09515-30010  
    09950-70010   (09951-07100)



24. INSTALL TRANSFER LOW PLANETARY GEAR SPLINE PIECE


    F043507
  1. Using a screwdriver, install the spline piece and low planetary gear with the snap ring.



25. INSTALL TRANSFER LOW PLANETARY GEAR BEARING


Q007440E01
  1. Using SST and a press, tap in a new low planetary gear bearing.

    SST
    09950-60010   (09951-00570)
    09950-70010   (09951-07100)

    Press in depth:
    7.7 to 8.3 mm (0.303 to 0.327 in.)



26. INSTALL TRANSFER INPUT BEARING SHAFT SNAP RING


    F043468
  1. Select a snap ring that allows the minimum axial play.
    Mark
    Thickness mm (in.)
    1
    1.45 to 1.50 (0.0571 to 0.0591)
    2
    1.50 to 1.55 (0.0591 to 0.0610)
    3
    1.55 to 1.60 (0.0610 to 0.0630)
    4
    1.60 to 1.65 (0.0630 to 0.0650)
    5
    1.65 to 1.70 (0.0650 to 0.0669)

  1. Using a snap ring expander, install a new snap ring.



27. INSTALL TRANSFER NO. 1 INPUT SHAFT SEAL RING


    F043460
  1. Apply gear oil to the oil seal ring.

  1. Engage securely to eliminate clearance as shown in the illustration.



28. INSTALL TRANSFER LOW PLANETARY GEAR BEARING


    F043454E01
  1. Install the transfer low planetary gear bearing.



29. INSTALL NO. 1 TRANSFER THRUST BEARING RACE


30. INSTALL TRANSFER INPUT SHAFT


31. INSTALL MANUAL TRANSFER PLANETARY CARRIER WASHER


    F043453
  1. Install the manual transfer planetary carrier washer.



32. INSTALL TRANSFER INPUT GEAR STOPPER BALL


33. INSTALL TRANSFER INPUT GEAR STOPPER


34. INSTALL TRANSFER INPUT GEAR STOPPER SHAFT SNAP RING


    F043514
  1. Select an input gear stopper shaft snap ring that allows 0.05 to 0.15 mm (0.0020 to 0.0059 in.) axial play.
    Mark
    Thickness mm (in.)
    A
    2.10 to 2.15 (0.0827 to 0.0846)
    B
    2.15 to 2.20 (0.0846 to 0.0866)
    C
    2.20 to 2.25 (0.0866 to 0.0886)
    D
    2.25 to 2.30 (0.0886 to 0.0906)
    E
    2.30 to 2.35 (0.0906 to 0.0925)
    F
    2.35 to 2.40 (0.0925 to 0.0945)
    G
    2.40 to 2.45 (0.0945 to 0.0965)
    H
    2.45 to 2.50 (0.0965 to 0.0984)
    J
    2.50 to 2.55 (0.0984 to 0.1004)
    K
    2.55 to 2.60 (0.1004 to 0.1024)
    L
    2.60 to 2.65 (0.1024 to 0.1043)
    M
    2.65 to 2.70 (0.1043 to 0.1063)
    N
    2.70 to 2.75 (0.1063 to 0.1083)
    P
    2.75 to 2.80 (0.1083 to 0.1102)
    Q
    2.80 to 2.85 (0.1102 to 0.1122)
    R
    2.85 to 2.90 (0.1122 to 0.1142)
    S
    2.90 to 2.95 (0.1142 to 0.1161)
    T
    2.95 to 3.00 (0.1161 to 0.1181)
    U
    3.00 to 3.05 (0.1181 to 0.1201)



    Q007289
  1. Using a snap ring expander, install the new input gear stopper shaft snap ring.



35. INSTALL TRANSFER CASE OIL SEAL


    F043515E01
  1. Using SST and a hammer, tap in a new oil seal until its surface is flush with the case upper surface.

    SST
    09316-60011   (09316-00011)

  1. Coat the lip of the oil seal with MP grease.



36. INSTALL LOW PLANETARY GEAR ASSEMBLY WITH INPUT SHAFT SUB-ASSEMBLY


    F043450
  1. Install the low planetary gear assembly with input shaft sub-assembly.



    F043449
  1. Using a snap ring expander, install the shaft snap ring.



37. INSTALL TRANSFER OIL PUMP GEAR


    F043448
  1. Install transfer oil pump gear.



38. INSTALL TRANSFER OIL PUMP BODY O-RING


    F043463E01
  1. Coat a new O-ring with gear oil and install it to the oil pump body.



39. INSTALL TRANSFER OIL PUMP BODY SUB-ASSEMBLY


    F043447
  1. Install the oil pump body sub-assembly with the 3 bolts.

    Torque:
    7.8 N*m{ 80 kgf*cm , 69 in.*lbf }



40. INSTALL TRANSFER CASE MAGNET


41. INSTALL TRANSFER OIL SEPARATOR SUB-ASSEMBLY


    F043446
  1. Install the oil separator sub-assembly with the 3 bolts.

    Torque:
    7.8 N*m{ 80 kgf*cm , 69 in.*lbf }



42. INSTALL TRANSFER CASE PLUG
  1. Install the case plug No. 1 (filler plug) and a new gasket.

    Torque:
    37 N*m{ 380 kgf*cm , 27 ft.*lbf }



43. INSTALL TRANSFER CASE PLUG
  1. Install the case plug (drain plug) and a new gasket.

    Torque:
    37 N*m{ 380 kgf*cm , 27 ft.*lbf }



44. INSTALL TRANSFER SHIFT ACTUATOR ASSEMBLY


    F043445
  1. Install the shift actuator assembly with the 3 bolts.

    Torque:
    20 N*m{ 200 kgf*cm , 14 ft.*lbf }

  1. Using a screwdriver and hammer, drive in the snap ring.



45. INSTALL TRANSFER INPUT GEAR RADIAL BALL BEARING


    F043464E02
  1. Using SST and a press, install a new input gear radial ball bearing.

    SST
    09316-60011   (09316-00031)



46. INSTALL TRANSFER DRIVEN SPROCKET BEARING


    F044041
  1. Using a press, install a new driven sprocket bearing.



47. INSTALL NO.2 STOPPER TRANSFER SHIFT SHAFT


    F043443
  1. Install No. 2 stopper transfer shift shaft.



48. INSTALL REAR OUTPUT SHAFT SUB-ASSEMBLY, NO. 1 GEAR SHIFT FORK, FRONT DRIVE CLUTCH SLEEVE, FRONT DRIVE CHAIN AND DRIVEN SPROCKET


    F043442
  1. Install the rear output shaft sub-assembly, gear shift fork No. 1 and drive sprocket to the front drive chain.



    F043441
  1. Install the rear output shaft sub-assembly, gear shift fork No. 1, front drive clutch sleeve, front drive chain and driven sprocket sub-assembly to the case rear.

    HINT:
    Check that the rear output shaft sub-assembly and driven sprocket sub-assembly turn lightly.



    F043440
  1. Using a snap ring expander, install the snap ring.



    F044399
  1. Using a screwdriver and hammer, drive in the snap ring.



    F044400
  1. Using a screwdriver and hammer, drive in the snap ring.



49. INSTALL NO.2 STOPPER TRANSFER SHIFT SHAFT


    F043437
  1. Install No. 2 stopper transfer shift shaft.



50. INSTALL OR ROLLER SHIFT INTER-LOCK PIN


51. INSTALL TRANSFER FRONT DRIVE SHIFT FORK SHAFT


    F043436
  1. Turn the front drive shift fork shaft, and install it on the rear case aligning the cut out position and the inter-lock pin position.



52. INSTALL TRANSFER SHIFT SHAFT STOPPER
  1. Install the shift shaft stopper with the bolt.

    Torque:
    19 N*m{ 195 kgf*cm , 14 ft.*lbf }



53. INSTALL TRANSFER GEAR SHIFT FORK NO. 2 WITH TRANSFER HIGH AND LOW CLUTCH SLEEVE


    F044401E01
  1. Install the gear shift fork No. 2 and high and low clutch sleeve.

  1. Install the bolt.

    Torque:
    24 N*m{ 245 kgf*cm , 18 ft.*lbf }



54. INSTALL TRANSFER OUTPUT SHAFT SPACER


55. INSTALL TRANSFER OUTPUT SHAFT FRONT NEEDLE ROLLER BEARING


56. INSTALL TRANSFER CASE REAR


    F043488E01
  1. Apply FIPG to the case rear, as shown.

    FIPG:
    Part No. 08826-00090, THREE BOND 1281 or equivalent



    F043433
  1. Install the clamp and case rear with the 12 bolts.

    Torque:
    28 N*m{ 285 kgf*cm , 21 ft.*lbf }



57. INSTALL COLLAR


    F043432
  1. Install collar.



58. INSTALL TRANSFER OUTPUT WASHER


59. INSTALL TRANSFER EXTENSION HOUSING TYPE T OIL SEAL


    F043516E02
  1. Using SST and a hammer, drive in a new oil seal until its surface is flush with the housing upper surface.

    SST
    09223-46011  
    09631-32020  

  1. Coat the lip of the oil seal with MP grease.



60. INSTALL TRANSFER EXTENSION HOUSING SUB-ASSEMBLY FRONT


    F043489E01
  1. Apply FIPG to the extension housing sub-assembly, as shown in the illustration.

    FIPG:
    Part No. 08826-00090, THREE BOND 1281 or equivalent

  1. Apply sealant to the bolt threads.

    Sealant:
    Part No. 08833-00080, THREE BOND 1344, LOCTITE 242 or equivalent



    F043431
  1. Install the extension housing sub-assembly with the 5 bolts.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }



61. INSTALL TRANSFER OUTPUT SHAFT COMPANION FLANGE OIL SEAL


    F043517E02
  1. Using SST and a hammer, drive in a new oil seal (front side).

    SST
    09950-60010   (09951-00320)
    09950-70010   (09951-07100)

  1. Coat the lip of the oil seal with MP grease.



62. INSTALL TRANSFER OUTPUT SHAFT COMPANION FLANGE OIL SEAL
  1. Drive in a new output shaft companion flange oil seal using the same procedure as for the oil seal.

    SST
    09950-60010   (09951-00320)
    09950-70010   (09951-07100)



63. INSTALL OUTPUT SHAFT COMPANION FLANGE SUB-ASSEMBLY


    F044048E02
  1. Install the companion flange sub-assembly (front side) onto the drive sprocket sub-assembly.

  1. Using SST to hold the companion flange, install a new companion flange lock nut.

    SST
    09330-00021  

    Torque:
    118 N*m{ 1,200 kgf*cm , 87 ft.*lbf }

  1. Using a chisel and hammer, stake the companion flange lock nut.



64. INSTALL OUTPUT SHAFT COMPANION FLANGE SUB-ASSEMBLY
  1. Using SST, install the companion flange sub-assembly using the same procedure as for the companion flange sub-assembly (rear side).

    Torque:
    118 N*m{ 1,200 kgf*cm , 87 ft.*lbf }

    SST
    09330-00021  



65. INSTALL BREATHER OIL DEFLECTOR


66. INSTALL TRANSFER CASE COVER SUB-ASSEMBLY


    F043428
  1. Install the case cover sub-assembly with the 4 bolts.

    Torque:
    18 N*m{ 185 kgf*cm , 13 ft.*lbf }



67. INSTALL TRANSFER COVER TYPE T OIL SEAL


    F043518E02
  1. Using SST and a hammer, drive in a new oil seal until its surface is flush with the retainer upper surface.

  1. Coat the lip of the oil seal with MP grease.

    SST
    09950-60010   (09951-00590)
    09950-70010   (09951-07100)



68. INSTALL TRANSFER RH BEARING RETAINER SUB-ASSEMBLY


    F043490E01
  1. Apply FIPG to the front bearing retainer sub-assembly, as shown in the illustration.

    FIPG:
    Part No. 08826-00090, THREE BOND 1281 or equivalent

  1. Apply sealant to the bolt threads.

    Sealant:
    Part No. 08833-00080, THREE BOND 1344, LOCTITE 242 or equivalent



    F043427
  1. Install the front bearing retainer sub-assembly with the 5 bolts.

    Torque:
    11.5 N*m{ 117 kgf*cm , 8 ft.*lbf }



69. INSTALL HOSES