Home › DRIVE LINE ยท VF4AM TRANSFER › TRANSFER ASSEMBLY

TRANSFER ASSEMBLY > INSPECTION

for Preparation Click here



1. INSPECT TRANSFER INPUT SHAFT


    Q007292
  1. Using a micrometer, measure the outer diameter of the input shaft journal surface.

    Minimum diameter:
    47.59 mm (1.8736 in.)

    If the outer diameter is less than the minimum, replace the input shaft.



    Q007293
  1. Using a dial indicator, measure the inside diameter of the input shaft bushing.

    Maximum diameter:
    48.14 mm (1.8593 in.)

    If the inside diameter exceeds the maximum, replace the input shaft.



2. INSPECT PLANETARY PINION GEAR THRUST CLEARANCE


    F043465
  1. Using a feeler gauge, measure the thrust clearance of the planetary pinion gear.

    Standard clearance:
    0.11 to 0.84 mm (0.0043 to 0.0331 in.)

    Maximum clearance:
    0.84 mm (0.0331 in.)

    If the clearance exceeds the maximum, replace the planetary gear assembly.



3. INSPECT PLANETARY PINION GEAR RADIAL CLEARANCE


    F043466
  1. Using a dial indicator, measure the radial clearance of the planetary pinion gear.

    Standard clearance:
    0.009 to 0.038 mm (0.0004 to 00015 in.)

    Maximum clearance:
    0.038 mm (0.0015 in.)

    If the clearance exceeds the maximum, replace the planetary gear assembly.



4. INSPECT DRIVE SPROCKET THRUST CLEARANCE


    F044049
  1. Using a feeler gauge, measure the thrust clearance of the drive sprocket.

    Standard clearance:
    0.15 to 0.24 mm (0.0059 to 0.0094 in.)

    Maximum clearance:
    0.24 mm (0.0094 in.)

    If the clearance exceeds the maximum, replace the drive sprocket.



5. INSPECT DRIVE SPROCKET RADIAL CLEARANCE


    F044050
  1. Using a dial indicator, measure the radial clearance of the drive sprocket.

    Standard clearance:
    0.01 to 0.06 mm (0.0004 to 0.0024 in.)

    Maximum clearance:
    0.06 mm (0.0024 in.)

    If the clearance exceeds the maximum, replace the drive sprocket, rear output shaft or needle roller bearing.



6. INSPECT TRANSFER OUTPUT SHAFT REAR


    F043511E01
  1. Using a micrometer, measure the outer diameter of the output shaft rear journal surface.

    Standard diameter:
    Part A:
    27.98 to 27.99 mm (1.1016 to 1.1020 in.)
    Part B:
    31.98 to 32.00 mm (1.2591 to 1.2598 in.)
    Part C:
    34.98 to 35.00 mm (1.3772 to 1.3780 in.)
    Part D:
    36.98 to 37.00 mm (1.4559 to 1.4567 in.)

    Minimum diameter:
    Part A:
    27.98 mm (1.1016 in.)
    Part B:
    31.98 mm (1.2591 in.)
    Part C:
    34.98 mm (1.3772 in.)
    Part D:
    36.98 mm (1.4559 in.)

    If the outer diameter is less than the minimum, replace the output shaft rear.



7. INSPECT HIGH AND LOW CLUTCH SLEEVE AND GEAR SHIFT FORK NO. 2 CLEARANCE


    F043481
  1. Using vernier calipers, measure the thickness of the gear shift fork No. 2 claw.

    Thickness:
    10 mm (0.3937 in.)

  1. Using vernier calipers, measure the groove of the high and low clutch sleeve.

    Distance:
    10.5 mm (0.4134 in.)

  1. Calculate a clearance between the high and low clutch sleeve and gear shift fork No. 2 clearance.

    Standard clearance:
    0.26 to 0.84 mm (0.0102 to 0.0331 in)

    Maximum clearance:
    0.84 mm (0.0331 in.)

    If the clearance exceeds the maximum, replace the high and low clutch sleeve or gear shift fork No. 2.



8. INSPECT FRONT DRIVE CLUTCH SLEEVE AND GEAR SHIFT FORK


    F043483
  1. Using vernier calipers, measure the thickness of the No. 1 gear shift fork claw.

    Thickness:
    10 mm (0.3937 in.)

  1. Using vernier calipers, measure the groove of the front drive clutch sleeve.

    Distance:
    10.5 mm (0.4134 in.)

  1. Calculate a clearance between the front drive clutch sleeve and No.1 gear shift fork.

    Standard clearance:
    0.26 to 0.84 mm (0.0102 to 0.0331 in.)

    Maximum clearance:
    0.84 mm (0.0331 in.)

    If the clearance exceeds the maximum, replace the front drive clutch sleeve or No.1 gear shift fork.



9. INSPECT CENTER DIFFERENTIAL CASE AND HIGH AND LOW CLUTCH SLEEVE


    F043493
  1. Check that the tip of the spline gear of the front drive clutch sleeve is not worn.

  1. Install the front drive clutch sleeve to the center differential case and check that the front drive clutch sleeve moves smoothly.



10. INSPECT CENTER DIFFERENTIAL CASE AND FRONT DRIVE CLUTCH SLEEVE


    F044398
  1. Check that the tip of the spline gear of the front drive clutch sleeve is not worn.

  1. Install the front drive clutch sleeve to the center differential case and check that the front drive clutch sleeve moves smoothly.