Home › BRAKE › BRAKE › HYDRAULIC BRAKE BOOSTER

HYDRAULIC BRAKE BOOSTER > DISASSEMBLY

for Preparation Click here



1. REMOVE BRAKE ACTUATOR BRACKET NO. 1


    F051421
  1. Using a hexagon wrench (5 mm), remove the bolt and brake actuator bracket No. 1 from the brake master cylinder.



    F051180
  1. Using a screwdriver, remove the brake fluid level warning switch connector from the brake actuator bracket No. 1.



2. REMOVE BRAKE MASTER CYLINDER RESERVOIR SUB-ASSEMBLY


    F051177E01
  1. Using a pin punch and hammer, remove the pin from the brake master cylinder reservoir sub-assembly.



    F051178E02
  1. Remove the screw and pull out the brake master cylinder reservoir sub-assembly.

  1. Remove the master cylinder reservoir filler cap.



3. REMOVE MASTER CYLINDER RESERVOIR GROMMET


    F051181E03
  1. Remove the 3 reservoir grommets from the master cylinder reservoir sub-assembly.



4. REMOVE BRAKE ACTUATOR HOSE


    F051182E02
  1. Using needle nose pliers, slide the 2 clips and remove the brake actuator hose and 2 clips.



5. REMOVE BRAKE ACTUATOR TUBE NO. 1


    F051183E01
  1. Using SST, remove the brake actuator tube No. 1 from the brake master cylinder.

    SST
    09023-00101  



6. REMOVE BRAKE BOOSTER WITH ACCUMULATOR PUMP ASSEMBLY


    F051185E01
  1. Using a screwdriver, remove the 2 plugs.



    F051186E02
  1. Remove the 2 screws and disconnect the wire harnesses from the master cylinder solenoid.



    F051187
  1. Using a screwdriver, remove the clip.



    F051188
  1. Remove the brake booster with accumulator pump assembly from the brake master cylinder.

  1. Remove the 2 brake booster pump collars and the 2 brake booster pump bushes from the brake booster with accumulator pump assembly.



    F051415E03
  1. Using a hexagon wrench (4 mm), remove the 2 pins.



7. REMOVE BRAKE BOOSTER PUMP BRACKET NO. 2


    F051189E02
  1. Using a hexagon wrench (5 mm), remove the 2 bolts and brake booster pump bracket No.2 from the brake master cylinder solenoid.

  1. Remove the brake booster pump bush from the brake booster pump bracket No. 2.



8. REMOVE BRAKE ACTUATOR BRACKET NO. 3


    F051423
  1. Remove the bolt and brake actuator bracket No. 3 from the brake master cylinder.



9. REMOVE BRAKE BOOSTER ACCUMULATOR ASSEMBLY


    F052314
  1. Secure the brake booster with accumulator pump assembly in a vise.

  1. Remove the brake booster accumulator assembly.

  1. Remove the O-ring from the brake booster accumulator assembly.

    NOTICE:
    Ensure no foreign matter enters the pump.

  1. Remove the brake booster accumulator pipe and compression spring.



10. REMOVE MASTER CYLINDER SOLENOID


    F051195E02
  1. Remove the 6 bolts and master cylinder solenoid.



    F051196
  1. Remove the gasket.



11. REMOVE MASTER CYLINDER PUSH ROD CLEVIS


    F051191E02
  1. Loosen the lock nut on the rod operating adapter, and remove the push rod clevis and lock nut.



    F051192E02
  1. Loosen the lock nut on the brake master cylinder side, and remove the rod operating adapter and lock nut.



12. REMOVE MASTER CYLINDER BOOT


13. REMOVE PISTON


    F051417E02
  1. Pressing the piston in with a screwdriver, use a pin or equivalent to push the C-ring from the hole in the master cylinder body then remove it with another screwdriver.

  1. Remove the piston, pulling it straight out, not at an angle.

    NOTICE:
    If pulled out at an angle, there is a possibility that the cylinder bore could be damaged.