Home › BRAKE › BRAKE › HYDRAULIC BRAKE BOOSTER

HYDRAULIC BRAKE BOOSTER > REASSEMBLY

for Preparation Click here



1. INSTALL PISTON


    F051194
  1. Apply lithium soap base glycol grease to a new piston.

  1. Install the piston.

  1. Using 2 screwdrivers, install a new snap ring while pressing on the piston.



2. INSTALL MASTER CYLINDER BOOT


3. INSTALL MASTER CYLINDER PUSH ROD CLEVIS


    F051192E02
  1. Install the brake master cylinder side lock nut and rod operating adapter on the brake master cylinder.

    Torque:
    26 N*m{ 260 kgf*cm , 19 ft.*lbf }



    F051191E02
  1. Install the lock nut and master cylinder push rod clevis on the rod operating adapter.

    Torque:
    26 N*m{ 260 kgf*cm , 19 ft.*lbf }



4. INSTALL MASTER CYLINDER SOLENOID


    F051196
  1. Install a new gasket.

    NOTICE:
    Keep all surfaces of the master cylinder solenoid, master cylinder and gasket, especially contact surfaces, away from water and dust.



    F051195E02
  1. Install the master cylinder solenoid with 6 new bolts.

    Torque:
    32 N*m{ 326 kgf*cm , 24 ft.*lbf }



5. INSTALL BRAKE BOOSTER ACCUMULATOR ASSEMBLY


    F052314
  1. Install the brake booster accumulator pipe and compression spring.

    NOTICE:
    Ensure that no foreign matter enters the pump.

  1. Install a new O-ring to the brake booster accumulator assembly.

  1. Install the brake booster accumulator assembly.

    Torque:
    57 N*m{ 585 kgf*cm , 42 ft.*lbf }



6. INSTALL BRAKE ACTUATOR BRACKET NO. 3


    F051423
  1. Install the brake actuator bracket No. 3 to the brake master cylinder with the bolt.

    Torque:
    7.8 N*m{ 80 kgf*cm , 69 in.*lbf }



7. INSTALL BRAKE BOOSTER PUMP BRACKET NO. 2


    F051189E02
  1. Install the brake booster pump bush to the brake booster pump bracket No. 2.

  1. Using a hexagon wrench (5 mm), install the brake booster pump bracket No. 2 with the 2 bolts.

    Torque:
    7.8 N*m{ 80 kgf*cm , 69 in.*lbf }



8. INSTALL BRAKE BOOSTER WITH ACCUMULATOR PUMP ASSEMBLY


    F051415E03
  1. Using a hexagon wrench (4 mm), install the 2 pins to the brake master cylinder.

    Torque:
    7.8 N*m{ 80 kgf*cm , 69 in.*lbf }

  1. Install the 2 brake booster pump collars and 2 brake booster pump bushes to the brake booster with accumulator pump assembly.



    F051188
  1. Install the brake booster with accumulator pump assembly to the brake master cylinder.



    F051199
  1. Install a new clip.



    F051186E03
  1. Install the wire harnesses with the 2 screws.

    Torque:
    2.9 N*m{ 30 kgf*cm , 26 in.*lbf }



    F051185E01
  1. Install 2 new plugs.



9. INSTALL BRAKE ACTUATOR TUBE NO. 1


    F051184E03
  1. Using SST, install the brake actuator tube No. 1 to the brake master cylinder assembly.

    SST
    09023-00101  

    Torque:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }

    NOTICE:
    Use a torque wrench with a fulcrum length of 250 mm (9.84 in.).

    HINT:
    This torque value is effective when SST is parallel to the torque wrench.



10. INSTALL BRAKE ACTUATOR HOSE


    F051182E02
  1. Using needle nose pliers, install the brake actuator hose and 2 clips.



11. INSTALL MASTER CYLINDER RESERVOIR GROMMET


    F051416
  1. Apply lithium soap base glycol grease to 3 new reservoir grommets.

  1. Install the 3 reservoir grommets to the brake master cylinder.

    HINT:
    Be careful of the size of each grommet.



12. INSTALL BRAKE MASTER CYLINDER RESERVOIR SUB-ASSEMBLY


    F051178E02
  1. Install the brake master cylinder reservoir sub-assembly with the screw.

    Torque:
    1.7 N*m{ 17 kgf*cm , 15 in.*lbf }

  1. Install the master cylinder reservoir filler cap.



    F051177E01
  1. Using a pin punch and hammer, install a new pin to the brake master cylinder reservoir sub-assembly.



13. INSTALL BRAKE ACTUATOR BRACKET NO. 1


    F051421E02
  1. Install the brake fluid level warning switch connector to the brake actuator bracket No. 1.

  1. Using a hexagon wrench (5 mm), install the brake actuator bracket No. 1 to the brake master cylinder with the bolt.

    Torque:
    7.8 N*m{ 80 kgf*cm , 69 in.*lbf }