Home › ENGINE ยท 1GR-FE › LUBRICATION › ENGINE OIL COOLER

ENGINE OIL COOLER > INSTALLATION

for Preparation Click here



1. INSTALL OIL COOLER ASSEMBLY
  1. Clean the oil cooler contact surface on the cooler mounting.

  1. Install a new O-ring onto the oil cooler.

  1. Apply a light coat of engine oil to the threads of the union bolt.



    A076454E01
  1. Install the oil cooler and plate washer with the union bolt.

    Torque:
    68 N*m{ 693 kgf*cm , 50 ft.*lbf }

  1. Connect the 2 oil cooler hoses to the oil cooler.



2. INSTALL OIL FILTER SUB-ASSEMBLY


    A076324E01
  1. Clean the oil filter contact surface on the oil filter bracket.

  1. Lubricate the rubber gasket of a new oil filter with clean engine oil.

  1. Tighten the oil filter by hand until the rubber gasket comes into contact with the seat of the filter bracket.



    A076325E03
  1. Using SST, tighten it an additional 3/4 turn to set the filter.

    SST
    09228-07501  

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }



3. ADD ENGINE COOLANT
  1. Slowly fill the system with engine coolant.

    Capacity:
    9.8 liters (10.4 Us qts, 8.6 Imp. qts)

    HINT:
    1. Use of improper coolants may damage the engine cooling system.
    2. Use only Toyota Super Long Life Coolant or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, and non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).
    3. New Toyota vehicles are filled with Toyota Super Long Life Coolant (color is pink, premixed ethylene glycol concentration is approximately 50 % and freezing temperature is -35°C (-31°F)). When replacing the coolant, Toyota Super Long Life Coolant is recommended.
    4. Observe the coolant level inside the radiator by pressing the inlet and outlet radiator hoses several times by hand. If the coolant level goes down, add the coolant.

    NOTICE:
    Do not substitute plain water for engine coolant.

  1. Install the radiator cap securely.

  1. Bleed the cooling system.

    1. Open the heater water valve while warming up the engine.

    2. Maintain the engine speed at 2,000 to 2,500 rpm and warm up the engine.

  1. Stop the engine and wait until the coolant cools down.

  1. Add coolant into the reservoir until the coolant level is FULL.



4. ADD ENGINE OIL
  1. Fill with fresh engine oil.

    Capacity:
    Drain and refill with oil filter change
    5.2 liters (5.5 US qts, 4.6 lmp. qts)
    Drain and refill without oil filter change
    4.9 liters (5.2 US qts, 4.3 lmp. qts)
    Dry fill
    6.0 liters (6.3 US qts, 5.3lmp. qts)

  1. Reinstall the oil filler cap.



5. INSPECT ENGINE OIL LEVEL


6. INSPECT ENGINE OIL LEAKS


7. CHECK FOR ENGINE COOLANT LEAKAGE
  1. Fill the radiator with coolant and attach a radiator cap tester.

  1. Pump it to 118 kPa (1.2 kgf/cm2 17.1 psi), then check for leakage.



8. INSTALL V-BANK COVER
  1. Install the V-bank cover with the 2 nuts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }