Home › DRIVE LINE ยท DIFFERENTIAL › REAR DIFFERENTIAL CARRIER ASSEMBLY

REAR DIFFERENTIAL CARRIER ASSEMBLY > REMOVAL

for Preparation Click here



1. REMOVE REAR WHEEL


2. SEPARATE PROPELLER SHAFT ASSEMBLY
See procedure 
Vehicle Type
Proceed to
2WD
Click here
4WD
Click here


3. DRAIN DIFFERENTIAL OIL


    D025304E03
  1. Stop the vehicle on a level place.

  1. Remove the differential filler plug and gasket.

  1. Check that the oil level is within 5mm (0 to 0.20 in.) of the bottom of the filler plug opening.

    NOTICE:
    1. Excessively large or small quantities of oil may cause problems.
    2. After replacing the oil, drive the vehicle and check the oil level again.

    HINT:
    If necessary, fill the rear differential carrier assembly with hypoid gear oil.

    Oil grade:
    Hypoid gear oil API GL-5
    Recommended viscosity:
    Above -18°C (0°F) SAE 90
    Below -18°C (0°F) SAE 80W or 80W-90

    Capacity:
    Front differential carrier assembly:
    1.35 to 1.45 litters
    (1.43 to 1.53 US qts, 1.19 to 1.27 lmp. qts)
    Rear differential carrier assembly
    3.00 to 3.10 litters
    (3.17 to 3.27 US qts, 2.64 to 2.72 lmp. qts)

  1. Check for oil leakage if the oil level is low.

  1. Install the differential filler plug and a new gasket.

    Torque:
    Front differential carrier assembly:
    39 N*m{ 398 kgf*cm , 29 ft.*lbf }
    Rear differential carrier assembly:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }



4. SEPARATE REAR SPEED SENSOR LH


    F043111
  1. Disconnect the speed sensor connector.



    F043113
  1. Remove the nut and speed sensor rear from the axle hub.

    NOTICE:
    1. Do not stick and foreign matter on the sensor tip.
    2. Do not let the foreign matter into the sensor installation hole.



5. SEPARATE REAR SPEED SENSOR RH

HINT:
Use the same procedure as for the LH side.



6. SEPARATE REAR DISC BRAKE CALIPER ASSEMBLY LH
  1. Remove the 2 bolts and separate the rear disc brake caliper assembly LH.

    HINT:
    Do not disconnect the flexible hose from the disc brake caliper assembly LH.



7. SEPARATE REAR DISC BRAKE CALIPER ASSEMBLY RH
  1. Remove the 2 bolts and separate the rear disc brake caliper assembly RH.

    HINT:
    Do not disconnect the flexible hose from the disc brake caliper assembly RH.



8. REMOVE REAR DISC
  1. Make matchmarks on the rear disc and the axle hub.

  1. Remove the rear disc.



9. REMOVE PARKING BRAKE SHOE RETURN TENSION SPRING


    D028127
  1. Using a needle-nose pliers, remove the 2 return tension springs.



10. REMOVE PARKING BRAKE SHOE STRUT COMPRESSION SPRING
  1. Slide out the front shoe and remove the compression spring.



11. REMOVE PARKING BRAKE SHOE STRUT LH


12. REMOVE PARKING BRAKE SHOE


13. REMOVE REAR AXLE SHAFT WITH BACKING PLATE


    F042741
  1. Remove the 4 nuts and rear axle shaft with backing plate.

  1. Remove the O-ring.



14. REMOVE REAR DIFFERENTIAL CARRIER ASSEMBLY


    C030284
  1. Remove the 10 nuts, 10 washers and differential carrier assembly.

    NOTICE:
    Be careful not to damage the contact surfaces of the differential carrier and rear axle housing.