Home › DRIVE LINE ยท DIFFERENTIAL › 1GR-FE FRONT DIFFERENTIAL CARRIER ASSEMBLY (for 4WD)

1GR-FE FRONT DIFFERENTIAL CARRIER ASSEMBLY (for 4WD) > REMOVAL

for Preparation Click here



1. REMOVE FRONT WHEELS


2. REMOVE REAR ENGINE UNDER COVER ASSEMBLY
  1. Remove the 6 bolts and engine under cover assembly.



3. REMOVE NO.1 ENGINE UNDER COVER SUB-ASSEMBLY
  1. Remove the 4 bolts and No. 1 engine under cover sub-assembly.



4. DRAIN DIFFERENTIAL OIL


    D025304E03
  1. Stop the vehicle on a level place.

  1. Remove the differential filler plug and gasket.

  1. Check that the oil level is within 5mm (0 to 0.20 in.) of the bottom of the filler plug opening.

    NOTICE:
    1. Excessively large or small quantities of oil may cause problems.
    2. After replacing the oil, drive the vehicle and check the oil level again.

    HINT:
    If necessary, fill the rear differential carrier assembly with hypoid gear oil.

    Oil grade:
    Hypoid gear oil API GL-5
    Recommended viscosity:
    Above -18°C (0°F) SAE 90
    Below -18°C (0°F) SAE 80W or 80W-90

    Capacity:
    Front differential carrier assembly:
    1.35 to 1.45 litters
    (1.43 to 1.53 US qts, 1.19 to 1.27 lmp. qts)
    Rear differential carrier assembly
    3.00 to 3.10 litters
    (3.17 to 3.27 US qts, 2.64 to 2.72 lmp. qts)

  1. Check for oil leakage if the oil level is low.

  1. Install the differential filler plug and a new gasket.

    Torque:
    Front differential carrier assembly:
    39 N*m{ 398 kgf*cm , 29 ft.*lbf }
    Rear differential carrier assembly:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }



5. REMOVE FRONT PROPELLER SHAFT ASSEMBLY


    C098708E05
  1. Place matchmarks on the propeller shaft flange and differential.

  1. Remove the 4 nuts, 4 bolts, 4 washers and front propeller shaft assembly.



    C098709E04
  1. Place matchmarks on the propeller shaft flange and transfer flange.

  1. Remove the 4 nuts, 4 washers and front propeller shaft assembly.



6. REMOVE FRONT AXLE HUB LH NUT


    F042732
  1. Remove the cotter pin and a lock cap.

  1. Remove the front axle hub nut.



7. REMOVE FRONT AXLE HUB RH NUT

HINT:
Use the same procedure as for the LH side.



8. SEPARATE FRONT STABILIZER LINK ASSEMBLY LH


    G020161
  1. Remove the 2 nuts and the front stabilizer link assembly LH.

    HINT:
    If the ball joint turns together with the nut, use a hexagon (6 mm) wrench to hold the stud.



9. SEPARATE FRONT STABILIZER LINK ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



10. SEPARATE FRONT SPEED SENSOR LH


    F044160
  1. Disconnect the speed sensor connector.



    F043112
  1. Using a hexagon wrench (5 mm), remove the bolt and front speed sensor from the steering knuckle.

    SST
    99999-60011  

    NOTICE:
    1. Do not stick and foreign matter on the sensor tip.
    2. Do not let the foreign matter into the sensor installation hole.



11. SEPARATE FRONT SPEED SENSOR RH

HINT:
Use the same procedure as for the LH side.



12. SEPARATE TIE ROD END SUB-ASSEMBLY LH


    F042735E01
  1. Remove the cotter pin and nut.

  1. Using SST, separate the tie rod end from the steering knuckle arm.

    SST
    09628-62011  



13. SEPARATE TIE ROD END SUB-ASSEMBLY RH

HINT:
Separate the RH side by the same procedures with the LH side.

SST
09628-62011  


14. REMOVE NO. 1 FRONT SUSPENSION ARM SUB-ASSEMBLY LOWER LH


    G020159
  1. Remove the 2 bolts, and separate the front lower ball joint attachment LH from the front axle.



    G020160E03
  1. Place matchmarks on the camber adjust cam No. 2 and toe adjust cam sub-assembly.

  1. Remove the nut, camber adjust cam No. 2, camber adjust cam assembly, bolt, toe adjust cam sub-assembly, toe adjust plate No. 2 and front suspension arm sub-assembly lower No. 1 LH.



    G020416E02
  1. Remove the cotter pin and the nut.

  1. Using SST, remove the front lower ball joint attachment LH.

    SST
    09628-00011  



15. REMOVE NO. 1 FRONT SUSPENSION ARM SUB-ASSEMBLY LOWER RH

HINT:
Use the same procedure as for the LH side.



16. REMOVE FRONT DRIVE SHAFT ASSEMBLY LH


F042739E01
  1. Using SST, remove the front drive shaft.

    SST
    09520-01010  
    09520-24010   (09520-32040)

    NOTICE:
    Be careful not to damage the oil seal.



17. REMOVE FRONT DRIVE SHAFT ASSEMBLY RH

HINT:
Remove the RH side by the same procedure with LH side.

SST
09520-01010  
09520-24010   (09520-32040)


18. REMOVE FRONT DIFFERENTIAL CARRIER ASSEMBLY


    C097020E05
  1. Remove the bolt and separate the front differential breather tube bracket.

  1. Support the front differential with a jack.

  1. Remove the front differential mount nut No. 1.

  1. Remove the 2 front mounting bolts and 2 nuts.

  1. Disconnect the actuator hose and connector.

  1. Lower the jack and remove the front differential assembly.

  1. Remove the 2 bolts and No. 3 front differential support.

  1. Remove the 5 bolts and 2 front differential supports.