Home › ENGINE · 2UZ-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P2430    Secondary Air Injection System Air Flow / Pressure Sensor Circuit Bank1

DTC    P2431    Secondary Air Injection System Air Flow / Pressure Sensor Circuit Range / Performance Bank1

DTC    P2432    Secondary Air Injection System Air Flow / Pressure Sensor Circuit Low Bank1

DTC    P2433    Secondary Air Injection System Air Flow / Pressure Sensor Circuit High Bank1

for Preparation Click here


DESCRIPTION


DTC No.
DTC Detection Condition
Trouble Area
P2430
While the engine is running, if voltage output of the pressure sensor indicates 0.1V or less, or indicates 4.8 V or more.
(1 trip detection logic)
  1. Pressure sensor
  2. Open or short in pressure sensor circuit
  3. ECM
P2431
The pressure sensor indicates less than 45 kPa (338 mHg), or more than 135 kPa (1013 mHg).
(1 trip detection logic)
  1. Pressure sensor
  2. Open or short in pressure sensor circuit
  3. ECM
P2432
While the engine is running, if voltage output of pressure sensor remains below 0.1 V.
(1 trip detection logic)
  1. Pressure sensor
  2. Open or short in pressure sensor circuit
  3. ECM
P2433
While the engine is running, if voltage output of the pressure sensor remains above 4.8 V.
(1 trip detection logic)
  1. Pressure sensor
  2. Open or short in pressure sensor circuit
  3. ECM

MONITOR DESCRIPTION

The ECM observes the pressure in the secondary air passage using the pressure sensor located on the air switching valve in the secondary air injection system.
If there is a defect in the sensor or the sensor circuit, the voltage level will deviate from the normal operating range, the ECM interprets this deviation as a defect in the pressure sensor circuit and sets a DTC.
A115345E03

MONITOR STRATEGY


Related DTCs
P2430: Air flow/pressure sensor circuit range check (Fluctuating)
P2431: Air flow/pressure sensor circuit rationality
P2432: Air flow/Pressure sensor circuit range check (Low voltage)
P2433: Air flow/pressure sensor circuit range check (High voltage)
Required sensors/Components
Pressure sensor
Frequency of operation
Continuous
Duration
P2430, P2432, P2433: 0.5 second
P2431: 5 second
MIL operation
P2430, P2432, P2433: Immediate
P2431: 2 driving cycles
Sequence operation
None

TYPICAL ENABLING CONDITIONS


The monitor will run whenever this DTC is not present
None
Starter
OFF
Time after starter turned from ON to OFF
2 seconds or more
Battery voltage
8 V or more
Ignition switch
ON

TYPICAL MALFUNCTION THRESHOLDS


P2430: 
Air pressure sensor voltage
Less than 0.1 V, or more than 4.8 V

P2431: 
Air pressure
Less than 45 kPa (338 mmHg), or more than 135 kPa (1013 mmHg)

P2432: 
Air pressure sensor voltage
Less than 0.1 V

P2433: 
Air pressure sensor voltage
More than 4.8 V

WIRING DIAGRAM


A115928E02


INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air/fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

1.CHECK HARNESS AND CONNECTOR (PRESSURE SENSOR - ECM)


    A115720E02
  1. Remove the intake manifold .

  1. Disconnect the A45 pressure sensor connector.

  1. Disconnect the E5 ECM connector.

  1. Measure the resistance between the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    VC (A45-3) - VC (E5-23)
    Below 1 Ω
    AIP (A45-2) - AIP (E5-32)
    E2 (A45-1) - E2 (E5-28)
    VC (A45-3) or VC (E5-23) - Body ground
    10 kΩ or higher
    AIP (A45-2) or AIP (E5-32) - Body ground



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


2.INSPECT PRESSURE SENSOR
  1. Remove the intake manifold .

  1. Connect the pressure gauge to the pressure sensor as shown in the illustration.

  1. Connect the intelligent tester to the DLC3 with CAN VIM.

  1. Turn the ignition switch ON and push the intelligent tester main switch ON (Do not start engine).

  1. Enter the following menus: DIAGNOSIS / ENHANCED OBD II / DATA LIST / AIR PMP PRS (A).

  1. Check the pressure displayed on the intelligent tester fluctuates when applying the pressure to the pressure sensor with the pressure gauge.

    OK:
    Pressure fluctuates in response to the pressure applied with pressure gauge.



NG
REPLACE PRESSURE SENSOR
OK

REPLACE ECM