SFI SYSTEM > DATA LIST / ACTIVE TEST |
| DATA LIST |
Warm up the engine.
Turn the ignition switch off.
Connect an intelligent tester to the DLC3.
Turn the ignition switch ON.
Turn the tester ON.
Select the following menu items: DIAGNOSIS / ENHANCED OBD II / DATA LIST.
Check the values by referring to the table below.
| Intelligent Tester Display | Measurement Item: Range (Display) | Normal Condition*
| Diagnostic Note |
| INJECTOR | Injection period of No. 1 cylinder: Min.: 0 ms, Max.: 32.64 ms | 1.6 to 2.4 ms: Idling | - |
| IGN ADVANCE | Ignition timing advance for No. 1 cylinder: Min.: -64 deg., Max.: 63.5 deg. | BTDC 7 to 24°: Idling | - |
| CALC LOAD | Load calculated by ECM: Min.: 0%, Max.: 100% |
| - |
| VEHICLE LOAD | Vehicle load: Min.: 0%, Max.: 25,700% | Actual vehicle load | - |
| MAF | Air flow rate from MAF meter: Min.: 0 g/sec., Max.: 655 g/sec. | 3.2 to 4.7 g/sec.: Idling | If value is approximately 0.0 g/ sec.:
|
| ENGINE SPD | Engine speed: Min.: 0 rpm, Max.: 16,383 rpm | 650 to 750 rpm: Idling | - |
| VEHICLE SPD | Vehicle speed: Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph) | Actual vehicle speed | Speed indicated on speedometer |
| COOLANT TEMP | Engine coolant temperature: Min.: -40°C (-40°F), Max.: 140°C (284°F) | 80 to 100°C (176 to 212°F): After warming up |
|
| INTAKE AIR | Intake air temperature: Min.: -40°C (-40°F), Max.: 140°C (284°F) | Equivalent to ambient air temperature |
|
| AIR-FUEL RATIO | Air-fuel ratio: Min.: 0, Max.: 1.999 | 0.8 to 1.2: Idling | - |
| PURGE DENSITY | Learning value of purge density: Min.: -50, Max.: 350 | -40 to 0%: Idling | Service data |
| PURGE FLOW | Purge flow: Min.: 0%, Max.: 102.4% | 0 to 100%: Idling | - |
| EVAP PURGE VSV | EVAP (Purge) VSV control duty: Min.: 0%, Max.: 100% | 0 to 100%: Idling | Order signal from ECM |
| VAPOR PRESS | Vapor pressure: Min.: -4,125 kPa, Max.: 2,125 kPa | 0 kPa: Fuel tank cap removed | Pressure inside fuel tank monitored by vapor pressure sensor |
| VAPOR PRESS CALC | Vapor pressure: (calculated) Min.: -5.632 kPa, Max.: 715.264 kPa | 0 kPa: Fuel tank cap removed | Pressure inside fuel tank monitored by vapor pressure sensor |
| KNOCK CRRT VAL | Correction learning value of knocking: Min.: -64 CA, Max.: 1,984 CA | 0 to 22° CA: Driving, 44 mph (70 km/h) | Service data |
| KNOCK FB VAL | Feedback value of knocking: Min.: -64 CA, Max.: 1,984 CA | -22 to 0° CA Driving, 44 mph (70 km/h) | Service data |
| CLUTCH | Clutch current: Min.: 0 %, Max.: 100 % | - | - |
| ETCS MAG CLUTCH | Electromagnetic Clutch: ON or OFF | - | - |
| EVAP VAPOR PRES | EVAP vapor pressure: Min.: -8,192 Pa, Max.: 8,191 Pa | 0 kPa: Fuel tank cap removed | - |
| ACCEL POS #1 | Absolute Accelerator Pedal Position (APP) No. 1: Min.: 0%, Max.: 100% | 10 to 22%: accelerator pedal released 54 to 86%: accelerator pedal fully depressed | - |
| ACCEL POS #2 | Absolute APP No. 2: Min.: 0 %, Max.: 100 % | 12 to 42%: accelerator pedal released 66 to 98%: accelerator pedal fully depressed | - |
| ACCEL POS #1 | APP sensor No. 1 voltage: Min.: 0 V, Max.: 4.98 V | - | ETCS freeze data |
| ACCEL POS #2 | APP sensor No. 2 voltage: Min.: 0 V, Max.: 4.98 V | - | ETCS freeze data |
| ACCEL POS #1 | APP sensor No. 1 voltage: Min.: 0 V, Max.: 5 V | 0.5 to 1.1 V: accelerator pedal released. 2.6 to 4.5 V: accelerator pedal fully depressed. | - |
| ACCEL POS #2 | APP sensor No. 2 voltage: Min.: 0 V, Max.: 5 V | 1.2 to 2.0 V: accelerator pedal released. 3.4 to 5.0 V: accelerator pedal fully depressed. | - |
| ACCEL IDL POS | Whether or not accelerator pedal position sensor detecting idle: ON or OFF | ON: Idling | - |
| THRTL LEARN VAL | Throttle valve fully closed (learned value): Min.: 0 V, Max.: 5 V | 0.4 to 0.8 V | - |
| ACCEL SSR #1 AD | Accelerator fully closed value No. 1 (AD): Min.: 0, Max.: 4.98 V | - | ETCS service data |
| ACCEL LRN VAL#1 | Accelerator fully closed learning value No. 1: Min.: 0, Max.: 124.512 | - | ETCS service data |
| ACCEL LRN VAL#2 | Accelerator fully closed learning value No. 2: Min.: 0, Max.: 124.512 | - | ETCS service data |
| FAIL #1 | Whether or not fail safe function executed: ON or OFF | ON: ETCS has failed | - |
| FAIL #2 | Whether or not fail safe function executed (Main CPU): ON or OFF | ON: ETCS has failed | - |
| ST1 | Starter signal: ON or OFF | ON: Cranking | - |
| SYS GUARD JUDGE | System guard: ON or OFF | - | ETCS service data |
| OPN MALFUNCTION | Open side malfunction: ON or OFF | - | ETCS service data |
| THROTTLE POS | Absolute throttle position sensor: Min.: 0%, Max.: 100% |
| Read value with intrusive operation (active test) |
| THROTTL IDL POS | Whether or not throttle position sensor detecting idle: ON or OFF | ON: Idling | - |
| THRTL REQ POS | Throttle requirement position: Min.: 0 V, Max.: 5 V | 0.5 to 1.0 V: Idling | - |
| THROTTLE POS | Throttle sensor positioning: Min.: 0%, Max.: 100% | 10 to 18%: Idling | Calculated value based on VTA1 |
| THROTTLE POS #2 | Throttle sensor positioning #2: Min.: 0%, Max.: 100% | - | Calculated value based on VTA2 |
| THROTTLE POS #1 | Throttle position sensor No. 1 output voltage: Min.: 0 V, Max.: 4.9 V | - | ETCS freeze data |
| THROTTLE POS #2 | Throttle position sensor No. 2 output voltage: Min.: 0 V, Max.: 4.9 V | - | ETCS freeze data |
| THROTTLE POS #1 | Throttle position No. 1: Min.: 0 V, Max.: 5 V |
| - |
| THROTTLE POS #2 | Throttle position No. 2: Min.: 0 V, Max.: 5 V |
| Read value with intrusive operation (active test) |
| THRTL COMND VAL | Throttle position command value: Min.: 0 V, Max.: 4.98 V | 0.5 to 4.8 V | ETCS service data |
| THROTTLE SSR #1 | Throttle sensor opener position No. 1: Min.: 0 V, Max.: 4.98 V | 0.6 to 0.9 V | ETCS service data |
| THROTTLE SSR #2 | Throttle sensor opener position No. 2: Min.: 0 V, Max.: 4.98 V | 2.2 to 2.6 V | ETCS service data |
| THRTL SSR #1 AD | Throttle sensor opener position No. 1 (AD): Min.: 0 V, Max.: 4.98 V | 0.6 to 0.9 V | ETCS service data |
| THROTTLE MOT | Whether or not throttle motor control permitted: ON or OFF | ON: Idling | Read value with ignition switch on (IG) (Do not start engine) |
| THROTTLE MOT | Throttle motor current: Min.: 0 A, Max.: 80 A | 0 to 3.0 A: Idling | - |
| THROTTLE MOT | Throttle motor: Min.: 0%, Max.: 100% | 0.5 to 40%: Idling | - |
| THROTTLE MOT | Throttle motor current: Min.: 0 A, Max.: 19.92 A | 0 to 3.0 A: Idling | - |
| THROTL OPN DUTY | Throttle motor opening duty ratio: Min.: 0%, Max.: 100% | 0 to 40%: Idling | When accelerator pedal is depressed, duty ratio increases |
| THROTL CLS DUTY | Throttle motor closed duty ratio: Min.: 0%, Max.: 100% | 0 to 40%: Idling | When accelerator pedal is released quickly, duty ratio increases |
| THRTL MOT (OPN) | Throttle motor duty ratio (open): Min.: 0%, Max.: 100% | - | ETCS service data |
| THRTL MOT (CLS) | Throttle motor duty ratio (close): Min.: 0%, Max.: 100% | - | ETCS service data |
| O2S B1 S2 | Heated oxygen sensor output voltage for bank 1 sensor 2: Min.: 0 V, Max.: 1.275 V | 0.1 to 0.9 V: Driving 44 mph (70 km/h) | Performing INJ VOL or A/F CONTROL function of ACTIVE TEST enables technician to check voltage output of sensor |
| O2S B2 S2 | Heated oxygen sensor output voltage for bank 2 sensor 2: Min.: 0 V, Max.: 1.275 V | 0.1 to 0.9 V: Driving 44 mph (70 km/h) | Performing INJ VOL or A/F CONTROL function of ACTIVE TEST enables technician to check voltage output of sensor |
| AFS B1 S1 | A/F sensor output voltage for bank 1 sensor 1: Min.: 0 V, Max.: 7.999 V | 2.8 to 3.8 V: Idling | Performing INJ VOL or A/F CONTROL function of ACTIVE TEST enables technician to check voltage output of sensor |
| AFS B2 S1 | A/F sensor output voltage for bank 2 sensor 1: Min.: 0 V, Max.: 7.999 V | 2.8 to 3.8 V: Idling | Performing INJ VOL or A/F CONTROL function of ACTIVE TEST enables technician to check voltage output of sensor |
| TOTAL FT #1 | Total fuel trim of bank 1 Average value for fuel trim system of bank 1: Min.: -0.5, Max.: 1.496 | -0.2 to 0.2: Idling | - |
| TOTAL FT #2 | Total fuel trim of bank 2 Average value for fuel trim system of bank 2: Min.: -0.5, Max.: 1.496 | -0.2 to 0.2: Idling | - |
| SHORT FT #1 | Short-term fuel trim of bank 1: Min.: -100%, Max.: 99.2% | 0 +/- 20% | Short-term fuel compensation used to maintain air-fuel ratio at stoichiometric air-fuel ratio |
| LONG FT #1 | Long-term fuel trim of bank 1: Min.: -100%, Max.: 99.2% | 0 +/- 20% | Overall fuel compensation carried out in long-term to compensate for continual deviation of short-term fuel trim from central value |
| SHORT FT #2 | Short-term fuel trim of bank 2: Min.: -100%, Max.: 99.2% | 0 +/- 20% | Short-term fuel compensation used to maintain air-fuel ratio at stoichiometric air-fuel ratio |
| LONG FT #2 | Long-term fuel trim of bank 2: Min.: -100%, Max.: 99.2% | 0 +/- 20% | Overall fuel compensation carried out in long-term to compensate for continual deviation of short-term fuel trim from central value |
| FUEL SYS #1 | Fuel system status (Bank 1): OL or CL or OL DRIVE or OL FAULT or CL FAULT | CL: Idling after warming up |
|
| FUEL SYS #2 | Fuel system status (Bank 2): OL or CL or OL DRIVE or OL FAULT or CL FAULT | CL: Idling after warming up |
|
| O2FT B1 S2 | Short-term fuel trim associated with bank 1 sensor 2: Min.: -100%, Max.: 99.2% | 0 +/- 20% | Same as SHORT FT #1 |
| O2FT B2 S2 | Short-term fuel trim associated with bank 2 sensor 2: Min.: -100%, Max.: 99.2% | 0 +/- 20% | Same as SHORT FT #2 |
| AF FT B1 S1 | Short-term fuel trim associated with bank 1 sensor 1: Min.: 0, Max.: 1.999 |
| - |
| AF FT B2 S1 | Short-term fuel trim associated with bank 2 sensor 1: Min.: 0, Max.: 1.999 |
| - |
| CAT TEMP B1S1 | Catalyst temperature (Bank 1, Sensor 1): Min.: -40°C (-40°F), Max.: 6,513.5°C (11,756.3°F) | - | - |
| CAT TEMP B2S1 | Catalyst temperature (Bank 2, Sensor 1): Min.: -40°C (-40°F), Max.: 6,513.5°C (11,756.3°F) | - | - |
| CAT TEMP B1S2 | Catalyst temperature (Bank 1, Sensor 2): Min.: -40°C (-40°F), Max.: 6,513.5°C (11,756.3°F) | - | - |
| CAT TEMP B2S2 | Catalyst temperature (Bank 2, Sensor 2): Min.: -40°C (-40°F), Max.: 6,513.5°C (11,756.3°F) | - | - |
| INI COOL TEMP | Initial engine coolant temperature: Min.: -40°C (-40°F), Max.: 140°C (284°F) | Close to ambient air temperature | Service data |
| INI INTAKE TEMP | Initial intake air temperature: Min.: -40°C (-40°F), Max.: 140°C (284°F) | Close to ambient air temperature | Service data |
| INJ VOL | Injection volume (cylinder 1): Min.: 0 ml, Max.: 2.048 ml | Max.: 0.5 ml | Quantity of fuel injected over 10 times |
| ACC RELAY | ACC relay signal: ON or OFF | ON: Cranking | - |
| STARTER RELAY | Starter relay signal: ON or OFF | ON: Cranking | - |
| STARTER SIG | Starter signal: ON or OFF | ON: Cranking | - |
| STARTER CONTROL | Starter Control: ON or OFF | ON: Cranking | - |
| PS SW | Power steering signal: ON or OFF | ON: Power steering operation | - |
| PS SIGNAL | Power steering signal: ON or OFF | ON: Steering wheel is first turned after ignition switch is turned on | This signal status is usually ON until ignition switch is turned off |
| CTP SW | Closed throttle position switch: ON or OFF |
| - |
| A/C SIG | A/C signal: ON or OFF | ON: A/C ON | - |
| PNP SW (NSW) | PNP switch status: ON or OFF | ON: P or N position | - |
| ELECT LOAD SIG | Electrical load signal: ON or OFF | ON: Headlights or defogger turned ON | - |
| STOP LIGHT SW | Stop light switch: ON or OFF | ON: Brake pedal depressed | - |
| +BM | Whether or not electric throttle control system power input: ON or OFF | ON: Idling | - |
| +BM VOLTAGE | +BM voltage: Min.: 0, Max.: 19.92 [V] | 10 to 15 V: Idling | ETCS service data |
| BATTERY VOLTAGE | Battery voltage: Min.: 0 V, Max.: 65.535 V | 9 to 14 V: Idling | - |
| ACTUATOR POWER | Actuator power supply: ON or OFF | ON: Idling | ETCS service data |
| ATM PRESSURE | Atmospheric pressure: Min.: 0 kPa, Max.: 150 kPa | Equivalent to atmospheric pressure (absolute pressure) | - |
| FUEL PMP SP CTL | Fuel pump speed control status: ON/H or OFF/L | Idling: ON | - |
| ACIS VSV | VSV for Acoustic Control Induction System Status: ON or OFF | - | ON: Open OFF: Closed |
| ACT VSV | A/C cut status for Active Test: ON or OFF | - | Active Test support data |
| VVT CTRL B2 | VVT control (bank 2) status: ON or OFF | - | Active Test support data |
| EVAP (Purge) VSV | VSV status for EVAP control: ON or OFF | - | Active Test support data |
| FUEL PUMP / SPD | Fuel pump/status: ON or OFF | - | Active Test support data |
| VVT CTRL B1 | VVT control (bank 1) status: ON or OFF | - | Active Test support data |
| VACUUM PUMP | Key-off EVAP system pump status: ON or OFF | - | Active Test support data |
| EVAP VENT VAL | Key-off EVAP system vent valve status: ON or OFF | - | Active Test support data |
| FAN MOTOR | Electric fan motor: ON or OFF | - | Active Test support data |
| TC/TE1 | TC and TE1 terminals of DLC3: ON or OFF | - | - |
| VVTL AIM ANGL #1 | VVT aim angle (bank 1 Intake side): Min.: 0%, Max.: 100% | 0%: Idling | VVT duty signal value during intrusive operation |
| VVT CHNG ANGL #1 | VVT change angle (bank 1 Intake side): Min.: 0° FR, Max.: 60° FR | 0 to 5° FR: Idling | Displacement angle during intrusive operation |
| VVT OCV DUTY B1 | VVT OCV (bank 1 Intake side) operation duty: Min.: 0%, Max.: 100% | 10 to 50%: Idling | Requested duty value for intrusive operation |
| VVTL AIM ANGL #2 | VVT aim angle (bank 2 Intake side): Min.: 0%, Max.: 100% | 0%: Idling | VVT duty signal value during intrusive operation |
| VVT CHNG ANGL #2 | VVT change angle (bank 2 Intake side): Min.: 0° FR, Max.: 60° FR | 0 to 5° FR: Idling | Displacement angle during intrusive operation |
| VVT OCV DUTY B2 | VVT OCV (bank 2 Intake side) operation duty: Min.: 0%, Max.: 100% | 0%: Idling | Requested duty value for intrusive operation |
| FC IDL | Fuel cut idle: ON or OFF | ON: Fuel cut operation | FC IDL = ON when throttle valve is fully closed and engine speed is over 2,800 rpm |
| FC TAU | Fuel cut TAU: Fuel cut during very light load: ON or OFF | ON: Fuel cut operation | Fuel cut being performed under very light load to prevent engine combustion from becoming incomplete |
| IGNITION | Ignition counter: Min.: 0, Max.: 800 | 0 to 800 | - |
| CYL #1 | Misfire ratio of cylinder 1: Min.: 0, Max.: 255 | 0% | This item displayed only during idling |
| CYL #2 | Misfire ratio of cylinder 2: Min.: 0, Max.: 255 | 0% | This item displayed only during idling |
| CYL #3 | Misfire ratio of cylinder 3: Min.: 0, Max.: 255 | 0% | This item displayed only during idling |
| CYL #4 | Misfire ratio of cylinder 4: Min.: 0, Max.: 255 | 0% | This item displayed only during idling |
| CYL #5 | Misfire ratio of cylinder 5: Min.: 0, Max.: 255 | 0% | This item displayed only during idling |
| CYL #6 | Misfire ratio of cylinder 6: Min.: 0, Max.: 255 | 0% | This item displayed only during idling |
| CYL ALL | All cylinders misfire rate: Min.: 0, Max.: 255 | 0 to 35 | - |
| MISFIRE RPM | Engine RPM for first misfire range: Min.: 0 rpm, Max.: 6,375 rpm | 0 rpm: Misfire 0 | - |
| MISFIRE LOAD | Engine load for first misfire range: Min.: 0 g/rev, Max.: 3.98 g/rev | 0 g/rev: Misfire 0 | - |
| MISFIRE MARGIN | Misfire monitoring: Min.: -100%, Max.: 99.22% | -100 to 99.2% | Misfire detecting margin |
| #CODES | #Codes: Min.: 0, Max.: 255 | - | Number of detected DTCs |
| CHECK MODE | Check mode: 0: OFF, 1: ON | ON: Check mode ON | Click here
|
| SPD TEST | Check mode result for vehicle speed sensor: 0: COMPL, 1: INCMPL | - | - |
| MISFIRE TEST | Check mode result for misfire monitor: 0: COMPL, 1: INCMPL | - | - |
| OXS2 TEST | Check mode result for HO2 sensor (bank 2): 0: COMPL, 1: INCMPL | - | - |
| OXS1 TEST | Check mode result for HO2 sensor (bank 1): 0: COMPL, 1: INCMPL | - | - |
| A/F SSR TEST B2 | Check mode result for air-fuel ratio sensor (bank 2): 0: COMPL, 1: INCMPL | - | - |
| A/F SSR TEST B1 | Check mode result for air-fuel ratio sensor (bank 1): 0: COMPL, 1: INCMPL | - | - |
| MIL | MIL status: ON or OFF | ON: MIL ON | - |
| MIL ON RUN DIST | MIL ON Run Distance: Min.: 0 km (0 mile), Max.: 65,535 km (40,723 mile) | Distance driven after DTC detected | - |
| MIL ON RUN TIME | Running time from MIL ON: Min.: 0 minute, Max.: 65,535 minutes | Running time after MIL ON | - |
| ENG RUN TIME | Engine run time: Min.: 0 second, Max.: 65,535 seconds | Time after engine start | Service data |
| TIME DTC CLEAR | Time after DTC cleared: Min.: 0 minute, Max.: 65,535 minutes | Time after DTCs erased | - |
| DIST DTC CLEAR | Distance after DTC cleared: Min.: 0 km (0 mile), Max.: 65,535 km/h (40,723 mile) | Distance driven after DTCs erased | - |
| WU CYC DTC CLEAR | Warm-up cycle after DTC cleared: Min.: 0, Max.: 255 | - | Number of warm-up cycles after DTC cleared |
| MODEL CODE | Model code: | - | Identifying the model code: GRN2### |
| ENGINE TYPE | Engine type: | - | Identifying the engine type: 1GR |
| CYLINDER NUMBER | Cylinder number: Min.: 0, Max.: 255 | - | Identifying the cylinder number: 4 or 6 |
| TRANSMISSION | Transmission type: | - | Identifying the transmission type: MT, ECT (5AT) or ECT (4AT) |
| DESTINATION | Destination | - | Identifying the destination: A (America) |
| MODEL YEAR | Model year: Min.: 1900, Max.: 2155 | - | Identifying the model year: 200# |
| SYSTEM | System identification | - | Identifying the engine system: GASLIN (gasoline engine) |
| ACTIVE TEST |
Connect an intelligent tester to the DLC3.
Start the engine.
Turn the tester ON.
Select the following menu items: DIAGNOSIS / ENHANCED OBD II / ACTIVE TEST.
Perform the ACTIVE TEST by referring to the table below.
| Intelligent Tester Display | Test Detail | Control Range | Diagnostic Note |
| INJ VOL | Change the injection volume | Between -12.5% and 25% |
|
| A/F CONTROL | Change the injection volume | Lower by 12.5% or increase by 25% |
|
| FUEL PMP SP CTL | Fuel pump speed control | ON (low speed)/OFF (high speed) | - |
| INTAKE CTL VSV1 | Activate the VSV for Acoustic Control Induction System (ACIS) | ON / OFF | - |
| EVAP VSV (ALONE) | Activate EVAP VSV control | ON / OFF | - |
| VVT CTRL B1 | Turn on and off OCV (Oil Control Valve) | ON / OFF |
|
| VVT CTRL B2 | Turn on and off OCV (Oil Control Valve) for VVT (Bank 2) | ON / OFF |
|
| A/C CUT SIG | Control A/C cut signal | ON / OFF | - |
| FUEL PUMP/SPD | Activate fuel pump (C/OPN Relay) | ON / OFF | - |
| TC/TE1 | Turn on and off TC and TE1 connection | ON / OFF |
|
| FC IDL PROHBT | Prohibit idling fuel cut control | ON / OFF | - |
| STARTER | Activate the Starter Relay | ON / OFF | Confirm that the engine is stopped |
| ACC CUT | Activate the ACC Cut Relay | ON / OFF | Confirm that the engine is stopped |
| ETCS OPEN SLOW | Throttle actuator | ON: throttle valve opens slowly | Test is possible when the following conditions are met:
|
| ETCS CLOSE SLOW | Throttle actuator | ON: throttle valve closes slowly | Same as above |
| ETCS OPEN FAST | Throttle actuator | ON: throttle valve opens fast | Same as above |
| ETCS CLOSE FAST | Throttle actuator | ON: throttle valve closes fast | Same as above |
| FUEL CUT #1 | Cylinder #1 injector fuel cut | ON / OFF | Test is possible while vehicle is stopped with engine idling. |
| FUEL CUT #2 | Cylinder #2 injector fuel cut | ON / OFF | Same as above |
| FUEL CUT #3 | Cylinder #3 injector fuel cut | ON / OFF | Same as above |
| FUEL CUT #4 | Cylinder #4 injector fuel cut | ON / OFF | Same as above |
| FUEL CUT #5 | Cylinder #5 injector fuel cut | ON / OFF | Same as above |
| FUEL CUT #6 | Cylinder #6 injector fuel cut | ON / OFF | Same as above |
| VVT B1 | Control the VVT (bank 1) | Between -128 and 127% This valve added to present OCV control duty 100%: Maximum advance -100% : Maximum retard | Engine stalls or idles roughly when VVT actuator operated by 100%. Test is possible while idling. |
| VVT B2 | Control the VVT (bank 2) | Between -128% and 127% | Same as above |
| VENT VALVE CALONE | Activate vent valve (built into pump module) | ON / OFF | - |
| VACUUM PUMP | Activate the Vacuum Pump built into pump module | ON / OFF | - |
| SYSTEM CHECK |
Connect an intelligent tester to the DLC3.
Turn the ignition switch ON.
Turn the tester ON.
Select the following menu items: DIAGNOSIS / ENHANCED OBD II / SYSTEM CHECK.
Perform the SYSTEM CHECK by referring to the table below.
| Intelligent Tester Displays | Test Details | Recommended Fuel Temperatures | Diagnostic Notes |
| EVAP SYS CHECK (AUTO OPERATION) | Perform 4 steps in order to operate EVAP key-off monitor automatically | 35°C (95°F) or less |
|
| EVAP SYS CHECK (MANUAL OPERATION) | Perform 4 steps in order to operate EVAP key-off monitor manually | 35°C (95°F) or less |
|