DTC P0327 Knock Sensor 1 Circuit Low Input (Bank 1 or Single Sensor) |
DTC P0328 Knock Sensor 1 Circuit High Input (Bank 1 or Single Sensor) |
DTC P0332 Knock Sensor 2 Circuit Low Input (Bank 2) |
DTC P0333 Knock Sensor 2 Circuit High Input (Bank 2) |
| DTC No. | DTC Detection Conditions | Trouble Areas |
| P0327 P0332 | Output voltage of knock sensor 1 or 2 is less than 0.5 V (1 trip detection logic) |
|
| P0328 P0333 | Output voltage of knock sensor 1 or 2 is more than 4.5 V (1 trip detection logic) |
|

| Items | Contents |
| Terminals | KNK1 - EKNK or KNK2 - EKN2 |
| Equipment Settings | 0.01 to 10 V/Division, 0.01 to 10 msec./Division |
| Conditions | Keep engine speed at 4,000 rpm with warm engine |
| Related DTCs | P0327: Knock sensor (Bank 1) range check (Low voltage) P0328: Knock sensor (Bank 1) range check (High voltage) P0332: Knock sensor (Bank 2) range check (Low voltage) P0333: Knock sensor (Bank 2) range check (High voltage) |
| Required Sensors / Components (Main) | Knock sensor |
| Required Sensors / Components (Related) | MAF meter, Crankshaft position sensor, ECT sensor |
| Frequency of Operation | Continuous |
| Duration | 1 second |
| MIL Operation | Immediate |
| Sequence of Operation | None |
| The monitor will run whenever these DTCs are not present | None |
| Battery voltage | 10.5 V or more |
| Time after engine start | 5 seconds or more |
| Ignition switch | ON |
| Starter | OFF |
| Knock sensor voltage | Less than 0.5 V |
| Knock sensor voltage | More than 4.5 V |

| 1.READ VALUE OF DTC OUTPUT (CHECK KNOCK SENSOR CIRCUIT) |
![]() |
Disconnect the ED1 connector.
Using lead wires, connect the connectors as follows.
| Male Connector - Female Connector |
| Terminal 2 - Terminal 4 |
| Terminal 5 - Terminal 6 |
| Terminal 4 - Terminal 2 |
| Terminal 6 - Terminal 5 |
Warm up the engine.
Run the engine at 3,000 rpm for 10 seconds or more.
Connect the intelligent tester to the DLC3.
Turn the ignition switch on and turn the intelligent tester on.
Select the item: DIAGNOSIS / ENHANCED OBD II / DTC INFO / CURRENT CODES.
Read DTCs.
| Display | Proceed to |
| DTCs same as when vehicle brought in P0327, P0328 → P0327, P0328 or P0332, P0333 → P0332, P0333 | A |
| DTCs different from when vehicle brought in P0327, P0328 → P0332, P0333 or P0332, P0333 → P0327, P0328 | B |
Reconnect the ED1 connector.
|
| ||||
| A | |
| 2.CHECK HARNESS OR CONNECTOR (CONNECTOR - ECM) |
![]() |
Disconnect the ED1 connector.
Disconnect the E5 ECM connector.
Measure the resistance.
| Tester Connections | Specified Conditions |
| ED1 female connector 2 - KNK1 (E5-29) | Below 1 Ω |
| ED1 female connector 5 - EKNK (E5-28) | Below 1 Ω |
| ED1 female connector 4 - KNK2 (E5-21) | Below 1 Ω |
| ED1 female connector 6 - EKN2 (E5-20) | Below 1 Ω |
| Tester Connections | Specified Conditions |
| ED1 female connector 2 or KNK1 (E5-29) - Body ground | 10 kΩ or higher |
| ED1 female connector 5 or EKNK (E5-28) - Body ground | 10 kΩ or higher |
| ED1 female connector 4 or KNK2 (E5-21) - Body ground | 10 kΩ or higher |
| ED1 female connector 6 or EKN2 (E5-20) - Body ground | 10 kΩ or higher |
Reconnect the ED1 connector.
Reconnect the ECM connector.
|
| ||||
| OK | |
| 3.INSPECT ECM |
![]() |
Disconnect the E5 ECM connector.
Turn the ignition switch on.
Measure the voltage between the ECM terminals.
| Tester Connections | Specified Conditions |
| KNK1 (E5-29) - EKNK (E5-28) | 4.5 to 5.5 V |
| KNK2 (E5-21) - EKN2 (E5-20) | 4.5 to 5.5 V |
Reconnect the ECM connector.
|
| ||||
| OK | ||
| ||
| 4.CHECK KNOCK SENSOR |
![]() |
Check the knock sensor installation.
|
| ||||
| OK | |
| 5.INSPECT KNOCK SENSOR |
![]() |
Disconnect the ED1 connector.
Measure the resistance between the terminals of the ED1 male connector.
| Tester Connections | Specified Conditions |
| ED1 male connector 2 - 5 | 120 to 280 kΩ |
| ED1 male connector 4 - 6 | 120 to 280 kΩ |
Reconnect the connector.
|
| ||||
| NG | |
| 6.CHECK HARNESS AND CONNECTOR (CONNECTOR - KNOCK SENSOR) |
![]() |
Disconnect the ED1 connector.
Disconnect the K1 and K2 knock sensor connectors.
Measure the resistance.
| Tester Connections | Specified Conditions |
| ED1 male connector 2 - K1-2 | Below 1 Ω |
| ED1 male connector 5 - K1-1 | Below 1 Ω |
| ED1 male connector 4 - K2-2 | Below 1 Ω |
| ED1 male connector 6 - K2-1 | Below 1 Ω |
| Tester Connections | Specified Conditions |
| ED1 male connector 2 or K1-2 - Body ground | 10 kΩ or higher |
| ED1 male connector 5 or K1-1 - Body ground | 10 kΩ or higher |
| ED1 male connector 4 or K2-2 - Body ground | 10 kΩ or higher |
| ED1 male connector 6 or K2-1 - Body ground | 10 kΩ or higher |
Reconnect the connector.
Reconnect the knock sensor connector.
|
| ||||
| OK | ||
| ||