DTC P0011 Camshaft Position "A" - Timing Over-Advanced or System Performance (Bank 1) |
DTC P0012 Camshaft Position "A" - Timing Over-Retarded (Bank 1) |
DTC P0021 Camshaft Position "A" - Timing Over-Advanced or System Performance (Bank 2) |
DTC P0022 Camshaft Position "A" - Timing Over-Retarded (Bank 2) |
| DTC No. | DTC Detection Conditions | Trouble Areas |
| P0011 P0021 | Advanced cam timing: With warm engine and engine speed of between 550 rpm and 4,000 rpm, all conditions (a), (b) and (c) are met (1 trip detection logic): (a) Difference between target and actual intake valve timings is more than 5° CA (Crankshaft Angle) for 4.5 seconds (b) Current intake valve timing is fixed (timing changes less than 5° CA in 5 seconds) (c) Variations in VVT controller timing are more than 19° CA of maximum delayed timing (advanced) |
|
| P0012 P0022 | Retarded cam timing: With warm engine and engine speed of between 550 rpm and 4,000 rpm, all conditions (a), (b) and (c) are met (2 trip detection logic): (a) Difference between target and actual intake valve is timings more than 5° CA (Crankshaft Angle) for 4.5 seconds (b) Current intake valve timing is fixed (timing changes less than 5° CA in 5 seconds) (c) Variations in VVT controller timing is 19° CA or less of maximum delayed timing (retarded) |
|
| Related DTCs | P0011: VVT system advance (Bank 1) P0012: VVT system retard (Bank 1) P0021: VVT system advance (Bank 2) P0022: VVT system retard (Bank 2) |
| Required sensors / components (Main) | VVT OCV, VVT Actuator |
| Required sensors / components (Related) | Crankshaft position sensor, Camshaft position sensor, ECT sensor |
| Frequency of operation | Once per driving cycles |
| Duration | Less than 10 seconds |
| MIL operation | P0011 and P0021: Immediate P0012 and P0022: 2 driving cycles |
| Sequence operation | None |
| The monitor will run whenever these DTCs are not present | P0100, P0101, P0102, P0103 (MAF Sensor), P0115, P0116, P0117, P0118 (ECT Sensor), P0125 (Insufficient ECT for Closed Loop), P0335 (CKP Sensor), P0340 (VVT Sensor 1, 2), P0351, P0352, P0353, P0354, P0355, P0356 (Ignitor) |
| Battery voltage | 11 V or more |
| Engine RPM | 500 to 4,000 rpm |
| ECT | 75 to 100°C (167 to 212°F) |
| Duration of valve timing | More than 5° CA (Crankshaft angle) |
| Valve timing | No change at advanced valve timing |
| Duration of valve timing | More than 5° CA (Crankshaft angle) |
| Valve timing | No change at retarded valve timing |
| Abnormal bank | Advanced timing over (Valve timing is out of specified range) | Retarded timing over (Valve timing is out of specified range) |
| Bank 1 | P0011 | P0012 |
| Bank 2 | P0021 | P0022 |
| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0011, P0012, P0021 OR P0022) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on and turn the tester on.
Select the following menu items: DIAGNOSIS / ENHANCED OBD II / DTC INFO / CURRENT CODES.
Read DTCs.
| Display (DTC Output) | Proceed to |
| P0011, P0012, P0021 or P0022 | A |
| P0011, P0012, P0021 or P0022 and other DTCs | B |
|
| ||||
| A | |
| 2.PERFORM ACTIVE TEST BY INTELLIGENT TESTER (OPERATE OCV) |
Connect the intelligent tester to the DLC3.
Start the engine and turn the tester on.
Warm up the engine.
Select the following menu items on the tester: DIAGNOSIS / ENHANCED OBD II / ACTIVE TEST / VVT CTRL B1.
Check the engine speed while operating the Oil Control Valve (OCV) using the tester.
| Tester Operations | Specified Conditions |
| OCV OFF | Normal engine idle speed |
| OCV ON | Engine idles roughly or stalls (soon after OCV switched from OFF to ON) |
|
| ||||
| OK | |
| 3.CHECK WHETHER DTC OUTPUT RECURS (DTC P0011, P0012, P0021 OR P0022) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on and turn the tester on.
Clear DTCs (Click here).
Start the engine and warm it up.
Select check mode using the tester (Click here).
Drive the vehicle for more than 10 minutes.
Read DTCs using the tester.
|
| ||||
| OK | ||
| ||
| 4.CHECK VALVE TIMING (CHECK FOR LOOSE AND JUMPED TEETH ON TIMING CHAIN) |
![]() |
Remove the cylinder head covers RH and LH.
Turn the crankshaft to align the matchmarks of the crankshaft.
Align the notch of the crankshaft pulley to the "0" position.
Check if the matchmarks of the camshaft pulley and camshaft bearing cap align.
Turn the crankshaft clockwise by 360° if the matchmarks do not align. Check if they align once again.
|
| ||||
| OK | |
| 5.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (OCV) |
![]() |
Remove the OCV.
Measure the resistance between the terminals of the OCV.
Apply the positive battery voltage to terminal 1 and negative battery voltage to terminal 2. Check the valve operation.
Reinstall the OCV.
|
| ||||
| OK | |
| 6.CHECK OIL PIPE AND OIL CONTROL VALVE FILTER |
|
| ||||
| OK | |
| 7.REPLACE CAMSHAFT TIMING GEAR ASSEMBLY |
| NEXT | |
| 8.CHECK WHETHER DTC OUTPUT RECURS |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and turn the tester on.
Clear DTCs (Click here).
Start the engine and warm it up.
Select the check mode using the tester (Click here).
Drive the vehicle for more than 10 minutes.
Confirm that no DTC is set using the tester.
|
| ||||
| OK | ||
| ||