DTC P0115 Engine Coolant Temperature Circuit |
DTC P0117 Engine Coolant Temperature Circuit Low Input |
DTC P0118 Engine Coolant Temperature Circuit High Input |
| DTC No. | Proceed to | DTC Detection Conditions | Trouble Areas |
| P0115 | Step 1 | Open or short in Engine Coolant Temperature (ECT) sensor circuit for 0.5 seconds (1 trip detection logic) |
|
| P0117 | Step 4 | Short in Engine Coolant Temperature (ECT) sensor circuit for 0.5 seconds (1 trip detection logic) |
|
| P0118 | Step 2 | Open in Engine Coolant Temperature (ECT) sensor circuit for 0.5 seconds (1 trip detection logic) |
|
| Temperature Displayed | Malfunctions |
| -40°C (-40°F) | Open circuit |
| 140°C (284°F) or higher | Short circuit |
| Related DTCs | P0115: ECT sensor range check (Fluttering) P0117: ECT sensor range check (Low voltage) P0118: ECT sensor range check (High voltage) |
| Required Sensors / Components (Main) | Engine coolant temperature sensor |
| Required Sensors / Components (Related) | - |
| Frequency of Operation | Continuous |
| Duration | 0.5 seconds |
| MIL Operation | Immediate |
| Sequence of Operation | None |
| The monitor will run whenever these DTCs are not present | None |
| Engine coolant temperature sensor voltage | Less than 0.14 V or more than 4.91 V [More than 140°C (284°F), or less than -40°C (-40°F)] |
| Engine coolant temperature sensor voltage | Less than 0.14 V [More than 140°C (284°F)] |
| Engine coolant temperature sensor voltage | More than 4.91 V [Less than -40°C (-40°F)] |
| Engine coolant temperature sensor voltage | 0.14 V to 4.91 V [-40 to 140°C (-40 to 284°F)] |

| 1.READ VALUE OF INTELLIGENT TESTER (ENGINE COOLANT TEMPERATURE) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on.
Turn the tester on.
Select the following menu items: DIAGNOSIS / ENHANCED OBD II / DATA LIST / PRIMARY / COOLANT TEMP.
Read the value displayed on the tester.
| Temperature Displayed | Proceed to |
| -40°C (-40°F) | A |
| 140°C (284°F) or higher | B |
| Between 80°C and 97°C (176°F and 207°F) | C |
|
| ||||
|
| ||||
| A | |
| 2.READ VALUE OF INTELLIGENT TESTER (CHECK FOR OPEN IN WIRE HARNESS) |
![]() |
Disconnect the E2 Engine Coolant Temperature (ECT) sensor connector.
Connect terminals 1 and 2 of the ECT sensor connector on the wire harness side.
Connect the intelligent tester to the DLC3.
Turn the ignition switch on.
Turn the tester on.
Select the following menu items: DIAGNOSIS / ENHANCED OBD II / DATA LIST / PRIMARY / COOLANT TEMP.
Read the value displayed on the tester.
Reconnect the ECT sensor connector.
|
| ||||
| NG | |
| 3.READ VALUE OF INTELLIGENT TESTER (CHECK FOR OPEN IN ECM) |
![]() |
Disconnect the E4 ECT sensor connector.
Connect terminals THW and E2 of the E4 ECM connector.
Connect the intelligent tester to the DLC3.
Turn the ignition switch on.
Turn the tester on.
Select the following menu items: DIAGNOSIS / ENHANCED OBD II / DATA LIST / PRIMARY / COOLANT TEMP.
Read the value displayed on the tester.
Reconnect the ECT sensor connector.
|
| ||||
| NG | ||
| ||
| 4.READ VALUE OF INTELLIGENT TESTER (CHECK FOR SHORT IN WIRE HARNESS) |
![]() |
Disconnect the E2 ECT sensor connector.
Connect the intelligent tester to the DLC3.
Turn the ignition switch on.
Turn the tester on.
Select the following menu items: DIAGNOSIS / ENHANCED OBD II / DATA LIST / PRIMARY / COOLANT TEMP.
Read the value displayed on the tester.
Reconnect the ECT sensor connector.
|
| ||||
| NG | |
| 5.READ VALUE OF INTELLIGENT TESTER (CHECK FOR SHORT IN ECM) |
![]() |
Disconnect the E4 ECM connector.
Connect the intelligent tester to the DLC3.
Turn the ignition switch on.
Turn the tester on.
Select the following menu items: DIAGNOSIS / ENHANCED OBD II / DATA LIST / PRIMARY / COOLANT TEMP.
Read the value displayed on the tester.
Reconnect the ECM connector.
|
| ||||
| NG | ||
| ||