DTC P0120 Throttle / Pedal Position Sensor / Switch "A" Circuit |
DTC P0122 Throttle / Pedal Position Sensor / Switch "A" Circuit Low Input |
DTC P0123 Throttle / Pedal Position Sensor / Switch "A" Circuit High Input |
DTC P0220 Throttle / Pedal Position Sensor / Switch "B" Circuit |
DTC P0222 Throttle / Pedal Position Sensor / Switch "B" Circuit Low Input |
DTC P0223 Throttle / Pedal Position Sensor / Switch "B" Circuit High Input |
DTC P2135 Throttle / Pedal Position Sensor / Switch "A" / "B" Voltage Correlation |

| DTC No. | DTC Detection Conditions | Trouble Areas |
| P0120 | Output voltage of VTA1 quickly fluctuates beyond lower and upper malfunction thresholds for 2 seconds (1 trip detection logic) |
|
| P0122 | Output voltage of VTA1 is 0.2 V or less for 2 seconds (1 trip detection logic) |
|
| P0123 | Output voltage of VTA1 is 4.8 V or more for 2 seconds (1 trip detection logic) |
|
| P0220 | Output voltage of VTA2 quickly fluctuates beyond lower and upper malfunction thresholds for 2 seconds (1 trip detection logic) |
|
| P0222 | Output voltage of VTA2 is 1.75 V or less for 2 seconds (1 trip detection logic) |
|
| P0223 | Output voltage of VTA2 is 4.8 V or more, and VTA1 is between 0.2 V and 2.02 V, for 2 seconds (1 trip detection logic) |
|
| P2135 | Either condition (a) or (b) met (1 trip detection logic): (a) Difference between output voltages of VTA1 and VTA2 is 0.02 V or less for 0.5 seconds or more (b) Output voltage of VTA1 is 0.2 V or less, and VTA2 is 1.75 V or less, for 0.4 seconds or more |
|
| Tester Display | Accelerator Pedal Fully Released | Accelerator Pedal Fully Depressed |
| THROTTLE POS | 10 to 24% | 64 to 96% |
| THROTTLE POS #2 | 2.1 to 3.1 V | 4.5 to 5.0 V |
| Related DTCs | P0120: Throttle position sensor 1 range check (Fluctuating) P0122: Throttle position sensor 1 range check (Low voltage) P0123: Throttle position sensor 1 range check (High voltage) P0220: Throttle position sensor 2 range check (Fluctuating) P0222: Throttle position sensor 2 range check (Low voltage) P0223: Throttle position sensor 2 range check (High voltage) P2135: Throttle position sensor range check (Correlation) |
| Required Sensors / Components (Main) | Throttle position sensor |
| Required Sensors / Components (Related) | - |
| Frequency of Operation | Continuous |
| Duration | Accelerator pedal ON: 2 seconds Accelerator pedal OFF: 10 seconds P2135: 0.5 seconds or 0.4 seconds |
| MIL Operation | Immediate |
| Sequence of Operation | None |
| The monitor will run whenever these DTCs are not present | None |
| Ignition switch | ON |
| Throttle control motor power | ON |
| VTA1 voltage | 0.2 V or less, or 4.535 V or more |
| VTA1 voltage | 0.2 V or less |
| VTA1 voltage | 4.8 V or more |
| VTA2 voltage | 1.75 V or less, or 4.8 V or more |
| VTA2 voltage | 1.75 V or less |
| Both of the following conditions are met for 2 seconds or more: | Condition 1 and 2 |
| 1. VTA1 voltage | 0.2 to 2.02 V |
| 2. VTA2 voltage | 4.8 V or more |
| Either of the following conditions is met: | Condition 1 or 2 |
| 1. Difference between VTA1 and VTA2 voltage | 0.02 V or less |
| 2. Both of the following conditions are met: | Condition (a) and (b) |
| (a) VTA1 voltage | 0.2 V or less |
| (b) VTA2 voltage | 1.75 V or less |
| VTA1 voltage | 0.69 to 3.96 V |
| VTA2 voltage | 2.25 to 5.0 V |

| 1.READ VALUE OF INTELLIGENT TESTER (THROTTLE POS AND THROTTLE POS #2) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on and turn the intelligent tester on.
Select the following menu items: DIAGNOSIS / ENHANCED OBD II / DATA LIST / ETCS / THROTTLE POS and THROTTLE POS #2.
Check the values displayed on the tester.
| TP#1 (VTA1) When AP Released | TP#2 (VTA2) When AP Released | TP#1 (VTA1) When AP Depressed | TP#2 (VTA2) When AP Depressed | Trouble Areas | Proceed to |
| 0% | Between 0 V and 0.2 V | 0% | Between 0 V and 0.2 V | VC circuit open | A |
| 100% | Between 4.5 V and 5.0 V | 100 % | Between 4.5 V and 5.0 V | E2 circuit open | A |
| 0% or 100% | Between 2.1 V and 3.1 V (Fail-safe) | 0% or 100% | Between 2.1 V and 3.1 V (Fail-safe) | VTA1 circuit open or ground short | A |
| Approx. 19% (Fail-safe) | Between 0 V and 0.2 V, or 4.5 V and 5.0 V | Between 10% and 24% (Fail-safe) | Between 0 V and 0.2 V, or 4.5 V and 5.0 V | VTA2 circuit open or ground short | A |
| Between 10% and 24% | Between 2.1 V and 3.1 V | Between 64% and 96% (Not fail-safe) | Between 4.5 V and 5.0 V (Not fail-safe) | TP sensor circuit normal | B |
|
| ||||
| A | |
| 2.CHECK HARNESS AND CONNECTOR (THROTTLE POSITION SENSOR - ECM) |
![]() |
Disconnect the T2 throttle with motor body connector.
Disconnect the E4 ECM connector.
Measure the resistance.
| Tester Connections | Specified Conditions |
| VC (T2-5) - VC (E4-23) | Below 1 Ω |
| VTA1 (T2-6) - VTA1 (E4-20) | Below 1 Ω |
| VTA2 (T2-4) - VTA2 (E4-19) | Below 1 Ω |
| E2 (T2-3) - E2 (E4-28) | Below 1 Ω |
| Tester Connections | Specified Conditions |
| VC (T2-5) or VC (E4-23) - Body ground | 10 kΩ or higher |
| VTA1 (T2-6) or VTA1 (E4-20) - Body ground | 10 kΩ or higher |
| VTA2 (T2-4) or VTA2 (E4-19) - Body ground | 10 kΩ or higher |
Reconnect the throttle with motor body connector.
Reconnect the ECM connector.
|
| ||||
| OK | |
| 3.INSPECT ECM (VC VOLTAGE) |
![]() |
Disconnect the T2 throttle with motor body connector.
Turn the ignition switch on.
Measure the voltage between the terminals of the E4 ECM connector.
| Tester Connections | Specified Conditions |
| VC (T2-23) - E2 (E4-28) | 4.5 to 5.0 V |
Reconnect the throttle with motor body connector.
|
| ||||
| OK | |
| 4.REPLACE THROTTLE WITH MOTOR BODY ASSEMBLY |
Replace the throttle with motor body assembly .
| NEXT | |
| 5.CHECK WHETHER DTC OUTPUT RECURS (THROTTLE POSITION SENSOR DTCS) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on and turn the tester on.
Clear DTCs (Click here).
Start the engine.
Allow the engine to idle for 15 seconds or more.
Select the following menu items: DIAGNOSIS / ENHANCED OBD II / DTC INFO / CURRENT CODES.
Read DTCs.
| Display (DTC Output) | Proceed to |
| P0120, P0122, P0123, P0220, P0222, P0223 and/or P2135 | A |
| No output | B |
|
| ||||
| A | ||
| ||