DTC P0617 Starter Relay Circuit High |
| DTC No. | DTC Detection Conditions | Trouble Areas |
| P0617 | When conditions (a), (b) and (c) met, when positive (+B) battery voltage 10.5 V or more is applied to ECM for 20 seconds (1 trip detection logic): (a) Vehicle speed more than 12.43 mph (20 km/h) (b) Engine speed more than 1,000 rpm (c) STA signal ON |
|
| Related DTCs | P0617: Starter signal error |
| Required Sensors / Components (Main) | STARTER relay, PNP switch |
| Required Sensors / Components (Related) | Vehicle Speed Sensor, Crankshaft Position sensor |
| Frequency of Operation | Continuous |
| Duration | 20 seconds |
| MIL Operation | Immediate |
| Sequence of Operation | None |
| The monitor will run whenever these DTCs are not present | None |
| Battery voltage | 10.5 V or more |
| Vehicle speed | 12.43 mph (20 km/h) or more |
| Engine speed | 1,000 rpm or more |
| Starter signal | ON |

| 1.READ VALUE OF INTELLIGENT TESTER (STARTER SIGNAL) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on and turn the tester on.
Select the following menu items: DIAGNOSIS / ENHANCED OBD II / DATA LIST / ALL / STARTER SIG.
Check the value displayed on the tester when the ignition switch is turned on and START positions.
| Ignition Switch Positions | STARTER SIG |
| ON | OFF |
| START | ON |
|
| ||||
| NG | |
| 2.INSPECT PARK/NEUTRAL POSITION SWITCH |
![]() |
Inspect the Park/Neutral Position (PNP) switch.
Disconnect the P1 PNP switch connector.
Measure the resistance when the transmission gear selector lever is moved to each position.
| Gear Selector Lever Positions | Tester Connections | Specified Conditions |
| P | 2 - 6, 4 - 5 | Below 1 Ω |
| R | 1 - 2 | Below 1 Ω |
| N | 2 - 9, 4 - 5 | Below 1 Ω |
| D | 2 - 7 | Below 1 Ω |
| 2 | 2 - 3 | Below 1 Ω |
| L | 2 - 8 | Below 1 Ω |
Reconnect the PNP switch connector.
|
| ||||
| OK | |
| 3.READ VALUE OF INTELLIGENT TESTER (STARTER SIGNAL) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on and turn the tester on.
Select the following menu items: DIAGNOSIS / ENHANCED OBD II / DATA LIST / ALL / STARTER SIG.
Check the value displayed on the tester when the ignition switch is turned on and START positions.
| Ignition Switch Positions | STARTER SIG |
| ON | OFF |
| START | ON |
|
| ||||
| NG | |
| 4.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY |
![]() |
Disconnect the I18 ignition switch connector.
Check the resistance.
| Ignition Switch Positions | Tester Conditions | Specified Condition |
| LOCK | All Terminals | 10 kΩ or higher |
| ACC | 2-4 | Below 1 Ω |
| ON | 1-2, 1-4, 5-6 | Below 1 Ω |
| START | 1-3, 1-4, 3-4, 5-6, 5-7, 6-7 | Below 1 Ω |
Reconnect the ignition switch connector.
|
| ||||
| OK | |
| 5.READ VALUE OF INTELLIGENT TESTER (STARTER SIGNAL) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on and turn the tester on.
Select the following menu items: DIAGNOSIS / ENHANCED OBD II / DATA LIST / PRIMARY / STARTER SIG.
Check the value displayed on the tester when the ignition switch is turned on and START positions.
| Ignition Switch Positions | STARTER SIG |
| ON | OFF |
| START | ON |
|
| ||||
| NG | ||
| ||