DTC P2120 Throttle / Pedal Position Sensor / Switch "D" Circuit |
DTC P2122 Throttle / Pedal Position Sensor / Switch "D" Circuit Low Input |
DTC P2123 Throttle / Pedal Position Sensor / Switch "D" Circuit High Input |
DTC P2125 Throttle / Pedal Position Sensor / Switch "E" Circuit |
DTC P2127 Throttle / Pedal Position Sensor / Switch "E" Circuit Low Input |
DTC P2128 Throttle / Pedal Position Sensor / Switch "E" Circuit High Input |
DTC P2138 Throttle / Pedal Position Sensor / Switch "D" / "E" Voltage Correlation |

| DTC No. | DTC Detection Conditions | Trouble Areas |
| P2120 | VPA fluctuates rapidly beyond upper and lower malfunction thresholds for 0.5 seconds or more (1 trip detection logic) |
|
| P2122 | VPA 0.4 V or less for 0.5 seconds or more when accelerator pedal is fully released (1 trip detection logic) |
|
| P2123 | VPA 4.8 V or more for 2.0 seconds or more (1 trip detection logic) |
|
| P2125 | VPA2 fluctuates rapidly beyond upper and lower malfunction thresholds for 0.5 seconds or more (1 trip detection logic) |
|
| P2127 | VPA2 is 1.2 V or less for 0.5 seconds or more when accelerator pedal is fully released (1 trip detection logic) |
|
| P2128 | Conditions (a) and (b) continue for 2.0 seconds or more (1 trip detection logic): (a) VPA2 is 4.8 V or more (b) VPA between 0.4 V and 3.45 V |
|
| P2138 | Condition (a) or (b) continues for 2.0 seconds or more (1 trip detection logic): (a) Difference between VPA and VPA2 is 0.02 V or less (b) VPA is 0.4 V or less and VPA2 is 1.2 V or less |
|
| Trouble Areas | ACCEL POS #1 When AP Released | ACCEL POS #2 When AP Released | ACCEL POS #1 When AP Depressed | ACCEL POS #2 When AP Depressed |
| VCP circuit open | 0 to 0.2 V | 0 to 0.2 V | 0 to 0.2 V | 0 to 0.2 V |
| Open or ground short in VPA circuit | 0 to 0.2 V | 1.2 to 2.0 V | 0 to 0.2 V | 3.4 to 5.0 V |
| Open or ground short in VPA2 circuit | 0.5 to 1.1 V | 0 to 0.2 V | 2.6 to 4.5 V | 0 to 0.2 V |
| EPA circuit open | 4.5 to 5.0 V | 4.5 to 5.0 V | 4.5 to 5.0 V | 4.5 to 5.0 V |
| Normal condition | 0.5 to 1.1 V | 1.2 to 2.0 V | 2.6 to 4.5 V | 3.4 to 5.0 V |
| Related DTCs | P2120: Accelerator position sensor 1 (VPA) range check (Fluttering) P2122: Accelerator position sensor 1 (VPA) range check (Low voltage) P2123: Accelerator position sensor 1 (VPA) range check (High voltage) P2125: Accelerator position sensor 2 (VPA2) range check (Fluttering) P2127: Accelerator position sensor 2 (VPA2) range check (Low voltage) P2128: Accelerator position sensor 2 (VPA2) range check (High voltage) P2138: Accelerator position sensor correlation range check |
| Required Sensors / Components (Main) | Accelerator position sensor |
| Required Sensors / Components (Related) | - |
| Frequency of Operation | Continuous |
| Duration | 2 seconds |
| MIL Operation | Immediate |
| Sequence Operation | None |
| The monitor will run whenever these DTCs are not present | None |
| Ignition switch | ON |
| Throttle control motor power | ON |
| Either of the following conditions is met | Condition 1 or 2 |
| 1. VPA voltage when VPA2 is 0.04 V or more | 0.4 V or less |
| 2. VPA voltage | 4.8 or more |
| VPA1 voltage when VPA2 is 0.04 V or more | 0.4 V or less |
| VPA1 voltage | 4.8 V or more |
| Either of the following conditions is met | Condition 1 or 2 |
| 1. VPA2 voltage when VPA is 0.04 V or more | 1.2 V or less |
| 2. VPA2 voltage when VPA is 0.4 to 3.45 V | 4.8 V or more |
| VPA2 voltage when VPA1 is 0.04 V or more | 1.2 V or less |
| VPA2 voltage when VPA1 is 0.4 to 3.45 V | 4.8 V or more |
| Either of the following conditions is met: | Condition 1 or 2 |
| 1. Difference between VPA 1 and VPA2 voltage | 0.02 V or less |
| 2. Both of the following conditions are met: | Condition (a) and (b) |
| (a) VPA1 voltage | 0.4 V or less |
| (b) VPA2 voltage | 1.2 V or less |

| 1.READ VALUE OF INTELLIGENT TESTER (ACCEL POS #1 AND ACCEL POS #2) |
![]() |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on and turn the tester ON.
Select the following menu items: DIAGNOSIS / ENHANCED OBD II / DATA LIST / ALL / ACCEL POS #1 and ACCEL POS #2.
Read the values displayed on the tester.
| Accelerator Pedal Operations | ACCEL POS #1 (AP#1) | ACCEL POS #2 (AP#2) |
| Released | 0.5 to 1.1 V | 1.2 to 2.0 V |
| Depressed | 2.6 to 4.5 V | 3.4 to 5.0 V |
|
| ||||
| NG | |
| 2.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL POSITION SENSOR - ECM) |
![]() |
Disconnect the A24 Accelerator Pedal Position (APP) sensor connector.
Disconnect the E8 ECM connector.
Measure the resistance.
| Tester Connections | Specified Conditions |
| VPA (A24-6) - VPA (E8-18) | Below 1 Ω |
| EPA (A24-5) - EPA (E8-20) | Below 1 Ω |
| VCPA (A24-4) - VCPA (E8-26) | Below 1 Ω |
| VPA2 (A24-3) - VPA2 (E8-19) | Below 1 Ω |
| EPA2 (A24-2) - EPA2 (E8-21) | Below 1 Ω |
| VCP2 (A24-1) - VCP2 (E8-27) | Below 1 Ω |
| Tester Connections | Specified Conditions |
| VPA (A24-6) or VPA (E8-18) - Body ground | 10 kΩ or higher |
| EPA (A24-5) or EPA (E8-20) - Body ground | 10 kΩ or higher |
| VCPA (A24-4) or VCPA (E8-26) - Body ground | 10 kΩ or higher |
| VPA2 (A24-3) or VPA2 (E8-19) - Body ground | 10 kΩ or higher |
| EPA2 (A24-2) or EPA2 (E8-21) - Body ground | 10 kΩ or higher |
| VCP2 (A24-1) or VCP2 (E8-27) - Body ground | 10 kΩ or higher |
Reconnect the APP sensor connector.
Reconnect the ECM connector.
|
| ||||
| OK | |
| 3.INSPECT ECM (VCPA AND VCP2 VOLTAGE) |
![]() |
Disconnect the A24 APP sensor connector.
Turn the ignition switch on.
Measure the voltage between the terminals of the E8 ECM connector.
| Tester Connections | Specified Conditions |
| VCPA (E8-26) - EPA (E8-20) | 4.5 to 5.0 V |
| VCP2 (E8-27) - EPA2 (E8-21) | 4.5 to 5.0 V |
Reconnect the APP sensor connector.
|
| ||||
| OK | |
| 4.REPLACE ACCELERATOR PEDAL ROD ASSEMBLY |
Replace the accelerator pedal rod assembly .
| NEXT | |
| 5.CHECK WHETHER DTC OUTPUT RECURS (ACCELERATOR PEDAL POSITION SENSOR DTCS) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on and turn the tester on.
Clear DTCs (Click here).
Start the engine.
Allow the engine to idle for 15 seconds.
Select the following menu items on the tester: DIAGNOSIS / ENHANCED OBD II / DTC INFO / CURRENT CODES.
Read DTCs.
| Display (DTC Output) | Proceed to |
| P2120, P2122, P2123, P2125, P2127, P2128 and/or P2138 | A |
| No output | B |
|
| ||||
| A | ||
| ||