DTC P2121 Throttle / Pedal Position Sensor / Switch "D" Circuit Range / Performance |
| DTC No. | DTC Detection Conditions | Trouble Areas |
| P2121 | Difference between VPA and VPA2 is less than 0.4 V, or more than 1.2 V for 0.5 second (1 trip detection logic) |
|
| Related DTCs | P2121: Accelerator pedal position (APP) sensor (rationality) |
| Required Sensors / Components (Main) | Accelerator position sensor |
| Required Sensors / Components (Related) | - |
| Frequency of Operation | Continuous |
| Duration | 0.5 seconds |
| MIL Operation | Immediate |
| Sequence of Operation | None |
| The monitor will run whenever these DTCs are not present | None |
| Either of the following conditions is met | Condition 1 or 2 |
| 1. Ignition switch | ON |
| 2. Throttle control motor power | ON |
| Difference between VPA1 voltage (learned value) and VPA2 voltage (learned value) | Less than 0.4 V, or more than 1.2 V |
| 1.READ VALUE OF INTELLIGENT TESTER (ACCEL POS #1 AND ACCEL POS #2) |
![]() |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on and turn the tester on.
Select the following menu items: DIAGNOSIS / ENHANCED OBD II / DATA LIST / ALL / ACCEL POS #1 and ACCEL POS #2.
Read the values displayed on the tester.
| Accelerator Pedal Operations | ACCEL POS #1 (AP#1) | ACCEL POS #2 (AP#2) |
| Released | 0.5 to 1.1 V | 1.2 to 2.0 V |
| Depressed | 2.6 to 4.5 V | 3.4 to 5.0 V |
|
| ||||
| NG | |
| 2.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL POSITION SENSOR - ECM) |
![]() |
Disconnect the A24 Accelerator Pedal Position (APP) sensor connector.
Disconnect the E8 ECM connector.
Measure the resistance.
| Tester Connections | Specified Conditions |
| VPA1 (A24-6) - VPA (E8-18) | Below 1 Ω |
| EP1 (A24-5) - EPA (E8-20) | Below 1 Ω |
| VCP1(A24-4) - VCPA (E8-26) | Below 1 Ω |
| VPA2 (A24-3) - VPA2 (E8-19) | Below 1 Ω |
| EP2 (A24-2) - EPA2 (E8-21) | Below 1 Ω |
| VCP2 (A24-1) - VCP2 (E8-27) | Below 1 Ω |
| Tester Connections | Specified Conditions |
| VPA1 (A24-6) or VPA (E8-18) - Body ground | 10 kΩ or higher |
| EP1 (A24-5) or EPA (A24E8-20) - Body ground | 10 kΩ or higher |
| VCP1 (A24-4) or VCPA (E8-26) - Body ground | 10 kΩ or higher |
| VPA2 (A24-3) or VPA2 (E8-19) - Body ground | 10 kΩ or higher |
| EP2 (A24-2) or EPA2 (E84-21) - Body ground | 10 kΩ or higher |
| VCP2 (A24-1) or VCP2 (E8-27) - Body ground | 10 kΩ or higher |
Reconnect the APP sensor connector.
Reconnect the ECM connector.
|
| ||||
| OK | |
| 3.REPLACE ACCELERATOR PEDAL ROD ASSEMBLY |
Replace the accelerator pedal rod assembly .
| NEXT | |
| 4.CHECK WHETHER DTC OUTPUT RECURS (ACCELERATOR PEDAL POSITION SENSOR DTCS) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on and turn the tester on.
Clear DTCs (Click here).
Start the engine.
Allow the engine to idle for 15 seconds.
Select the following menu items on the tester: DIAGNOSIS / ENHANCED OBD II / DTC INFO / CURRENT CODES.
Read DTCs.
| Display (DTC Output) | Proceed to |
| P2121 | A |
| No output | B |
|
| ||||
| A | ||
| ||