DTC P2A00 A/F Sensor Circuit Slow Response (Bank 1 Sensor 1) |
DTC P2A03 A/F Sensor Circuit Slow Response (Bank 2 Sensor 1) |
| DTC No. | DTC Detection Conditions | Trouble Areas |
| P2A00 P2A03 | Calculated value for air-fuel ratio (A/F) sensor response rate deterioration level is less than threshold |
|


![]() |
| Related DTCs | P2A00: A/F sensor (Bank 1) slow response P2A03: A/F sensor (Bank 2) slow response |
| Required Sensors / Components (Main) | A/F sensor |
| Required Sensors / Components (Related) | Vehicle speed sensor, Crankshaft position sensor |
| Frequency of Operation | Once per driving cycle |
| Duration | 10 to 15 seconds |
| MIL Operation | 2 driving cycles |
| Sequence of Operation | None |
| The monitor will run whenever these DTCs are not present | P0031, P0032, P0051, P0052 (A/F Sensor heater Sensor 1), P0100, P0101, P0102, P0103 (MAF Sensor), P0110, P0112, P0113 (IAT Sensor), P0115, P0116, P0117, P0118 (ECT Sensor), P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (TP Sensor), P0125 (Insufficient ECT for Closed Loop), P0171, P0172 (Fuel System), P0300, P0301, P0302, P0303, P0304, P0305, P0306 (Misfire), P0335 (CKP Sensor), P0340 (CMP sensor), P0450, P0451, P0452, P0453, P0455, P0456 (EVAP System), P0500 (VSS), P2196, P2198 (A/F Sensor (Rationality)) |
| Active A/F control | Performing |
| Active A/F control is performed when the following conditions are met | - |
| Battery voltage | 11 V or more |
| Engine coolant temperature | 75°C (167°F) or more |
| Idle | OFF |
| Engine RPM | Less than 4,000 rpm |
| A/F sensor status | Activated |
| Fuel cut | OFF |
| Engine load | 10 to 70% |
| Shift position | 2 or more |
| Catalyst monitor | Not yet |
| Intake air amount | 2.5 to 8.2 g/s |
| Response rate deterioration level | Less than 0.2 V |
| Tester Display (Sensor) | Injection Volumes | Status | Voltages |
| AFS B1S1 or AFS B2S1 (A/F) | +25% | Rich | Less than 3.0 |
| AFS B1S1 or AFS B2S1 (A/F) | -12.5% | Lean | More than 3.35 |
| O2S B1S2 or O2S B2S2 (HO2) | +25% | Rich | More than 0.55 |
| O2S B1S2 or O2S B2S2 (HO2) | -12.5% | Lean | Less than 0.4 |
| Case | A/F Sensor (Sensor 1) Output Voltage | HO2 Sensor (Sensor 2) Output Voltage | Main Suspected Trouble Area | ||
| 1 | Injection Volume +25 % -12.5% | ![]() | Injection Volume +25% -12.5% | ![]() | - |
| Output Voltage More than 3.35 V Less than 3.0 V | ![]() | Output Voltage More than 0.55 V Less than 0.4 V | ![]() | ||
| 2 | Injection Volume +25% -12.5% | ![]() | Injection Volume +25% -12.5% | ![]() |
|
| Output Voltage Almost no reaction | ![]() | Output Voltage More than 0.55 V Less than 0.4 V | ![]() | ||
| 3 | Injection Volume +25% -12.5% | ![]() | Injection Volume +25% -12.5% | ![]() |
|
| Output Voltage More than 3.35 V Less than 3.0 V | ![]() | Output Voltage Almost no reaction | ![]() | ||
| 4 | Injection volume +25% -12.5% | ![]() | Injection Volume +25% -12.5% | ![]() |
|
| Output Voltage Almost no reaction | ![]() | Output Voltage Almost no reaction | ![]() | ||
| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2A00 AND/OR P2A03) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on.
Turn the tester on.
Select the following menu items: DIAGNOSIS / ENHANCED OBD II / DTC INFO / CURRENT CODES.
Read DTCs.
| Display (DTC Output) | Proceed to |
| P2A00 and/or P2A03 | A |
| P2A00 and/or P2A03 and other DTCs | B |
|
| ||||
| A | |
| 2.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE) |
![]() |
Disconnect the A12 or A13 A/F sensor connector.
Measure the resistance between the terminals of the A/ sensor connector.
| Tester Connections | Specified Conditions |
| HT (1) - +B (2) | 1.8 to 3.4 Ω at 20°C (68°F) |
| HT (1) - AF- (4) | 10 kΩ or higher |
| Tester Connections | Specified Conditions |
| HT (1) - +B (2) | 1.8 to 3.4 Ω at 20°C (68°F) |
| HT (1) - AF- (4) | 10 kΩ or higher |
Reconnect the A/F sensor connector.
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (A/F SENSOR - ECM) |
![]() |
Disconnect the A12 or A13 A/F sensor connector.
Turn the ignition switch on.
Measure the voltage between the +B terminal of the A/F sensor connector and body ground.
| Tester Connections | Specified Conditions |
| +B (A12-2) - Body ground | 9 to 14 V |
| +B (A13-2) - Body ground | 9 to 14 V |
Turn the ignition switch off.
Disconnect the B46 ECM connector.
Measure the resistance between the terminals of the A/F sensor connector and ECM connector.
| Tester Connections | Specified Conditions |
| HA1A (A12-1) - HA1A (E5-2) | Below 1 Ω |
| A1A+ (A12-3) - A1A+ (E5-22) | Below 1 Ω |
| A1A- (A12-4) - A1A- (E5-30) | Below 1 Ω |
| HA2A (A13-1) - HA2A (E5-1) | Below 1 Ω |
| A2A+ (A13-3) - A2A+ (E5-23) | Below 1 Ω |
| A2A- (A13-4) - A2A- (E5-31) | Below 1 Ω |
| Tester Connections | Specified Conditions |
| HA1A (A12-1) or HA1A (E5-2) - Body ground | 10 kΩ or higher |
| A1A+ (A12-3) or A1A+ (E5-22) - Body ground | 10 kΩ or higher |
| A1A- (A12-4) or A1A- (E5-30) - Body ground | 10 kΩ or higher |
| HA2A (A13-1) or HA2A (E5-1) - Body ground | 10 kΩ or higher |
| A2A+ (A13-3) or A2A+ (E5-23) - Body ground | 10 kΩ or higher |
| A2A- (A13-4) or A2A- (E5-31) - Body ground | 10 kΩ or higher |
Reconnect the ECM connector.
Reconnect the A/F sensor connector.

|
| ||||
| OK | |
| 4.PERFORM CONFIRMATION DRIVING PATTERN |
| NEXT | |
| 5.CHECK WHETHER DTC OUTPUT RECURS (DTC P2A00 AND/OR P2A03) |
Read DTCs using the intelligent tester.
Select the following menu items: DIAGNOSIS / ENHANCED OBD II / DTC INFO / CURRENT CODES.
| Display (DTC Output) | Proceed to |
| P2A00 and/or P2A03 | A |
| No output | B |
|
| ||||
| A | |
| 6.REPLACE AIR FUEL RATIO SENSOR |
| NEXT | |
| 7.PERFORM CONFIRMATION DRIVING PATTERN |
| NEXT | |
| 8.CHECK WHETHER DTC OUTPUT RECURS (DTC P2A00 AND/OR P2A03) |
Read DTCs using the intelligent tester.
Select the following menu items: DIAGNOSIS / ENHANCED OBD II / DTC INFO / CURRENT CODES.
| Display (DTC Output) | Proceed to |
| No output | A |
| P2A00 and/or P2A03 | B |
|
| ||||
| A | ||
| ||