Home › ENGINE · 1GR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

SFI SYSTEM > Fuel Pump Control Circuit

for Preparation Click here


DESCRIPTION

Refer to DTC P0230

WIRING DIAGRAM

Refer to DTC O0230

INSPECTION PROCEDURE

1.CHECK FUEL PUMP OPERATION
  1. Check if there is pressure in the fuel inlet hose .

    HINT:
    If there is fuel pressure, you will hear the sound of fuel flowing sound.



OK
Go to step 10
NG


2.PERFORM ACTIVE TEST BY INTELLIGENT TESTER (OPERATION OF CIRCUIT OPENING RELAY)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on and turn the tester on.

  1. Select the following menu items: DIAGNOSIS / ENHANCED OBD II / ACTIVE TEST / FUEL PUMP/ SPD.

  1. Check whether operating sounds can be heard while operating the relay using the tester.

    OK:
    Operating sounds can be heard from the relay.



OK
Go to step 5
NG


3.INSPECT CIRCUIT OPENING RELAY


    B016200
  1. Remove the circuit opening relay from the engine room R/B.

  1. Check the circuit opening relay resistance.

    Standard resistance:
    Tester Connections
    Specified Conditions
    3 - 5
    10 kΩ or higher
    3 - 5
    Below 1 Ω
    (when battery voltage applied to terminals 1 and 2)

  1. Reinstall the circuit opening relay.



NG
REPLACE CIRCUIT OPENING RELAY
OK


4.INSPECT ECM (FC VOLTAGE)


    A131509E59
  1. Turn the ignition switch on.

  1. Measure the voltage between the terminals of the E6 and E8 ECM connectors.

    Standard voltage:
    Tester Connections
    Specified Conditions
    FC (E8-10) - E1 (E6-1)
    9 to 14 V



OK
REPLACE ECM
NG

CHECK AND REPLACE HARNESS OR CONNECTOR (ECM - IGNITION SWITCH) 

5.INSPECT ECM POWER SOURCE CIRCUIT

HINT:
Refer to "ECM POWER SOURCE CIRCUIT" (Click here).



NG
REPAIR OR REPLACE ECM POWER SOURCE CIRCUIT
OK


6.INSPECT FUEL PUMP RELAY


    A030519
  1. Remove the fuel pump relay the engine room R/B.

  1. Check the fuel pump relay resistance.

    Standard resistance:
    Tester Connection
    Specified Condition
    3 - 4
    Below 1 Ω
    3 - 5
    10 kΩ or higher
    3 - 4
    10 kΩ or higher
    (when battery voltage applied to terminal 1 and 2)
    3 - 5
    Below 1 Ω
    (when battery voltage applied to terminal 1 and 2)

  1. Reinstall the fuel pump relay.



NG
REPLACE FUEL PUMP RELAY
OK


7.INSPECT FUEL PUMP ASSEMBLY


    A074356E25
  1. Inspect fuel pump resistance.

    1. Disconnect the F14 fuel pump connector.

    2. Measure the resistance between terminals 4 and 5.

      Standard resistance:
      0.2 to 3.0 Ω at 20°C (68°F)

  1. Inspect fuel pump operation.

    1. Apply battery voltage to both terminals. Check that the fuel pump operates.

      NOTICE:
      1. These tests must be done quickly (within 10 seconds) to prevent the coil from burning out.
      2. Keep the fuel pump as far away from the battery as possible.
      3. Always switch at the battery side.



NG
REPLACE FUEL PUMP ASSEMBLY
OK


8.CHECK HARNESS AND CONNECTOR (FUEL PUMP - FUEL PUMP RELAY RELAY, FUEL PUMP - BODY GROUND)


    A138729E01
  1. Check the harness and connector between the fuel pump and circuit opening relay.

    1. Disconnect the F14 fuel pump connector.

    2. Remove the Fuel pump relay from the engine room R/B.

    3. Measure the resistance between the terminals of the fuel pump relay and fuel pump connector.

      Standard resistance (Check for open):
      Tester Connections
      Specified Conditions
      Fuel pump (F14-4) - Fuel pump relay (4)
      Below 1 Ω

      Standard resistance (Check for short):
      Tester Connections
      Specified Conditions
      Fuel pump (F14-4) or Fuel pump relay (4) - Body ground
      10 kΩ or higher

    4. Reconnect the fuel pump connector.

    5. Reinstall the engine room junction block.

  1. Check the harness and connector between the fuel pump and body ground.

    1. Disconnect the fuel pump connector.

    2. Measure the resistance between the terminal of the fuel pump connector and body ground.

      Standard resistance (Check for open):
      Tester Connections
      Specified Conditions
      Fuel pump (F14-5) - Body ground
      Below 1 Ω

    3. Reconnect the fuel pump connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


9.CHECK HARNESS AND CONNECTOR (CIRCUIT OPENING RELAY - FUEL PUMP RELAY)


    A079233E01
  1. Remove the circuit opening relay from the engine room R/B.

  1. Remove the fuel pump relay from the engine room R/B.

  1. Check the resistance.

    Standard resistance (Check for open):
    Tester Connections
    Specified Conditions
    Circuit opening relay (3) - Fuel pump relay (3)
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connections
    Specified Conditions
    Circuit opening relay (3) or Fuel pump relay (3) - Body ground
    10 kΩ or higher

  1. Reinstall the circuit opening relay.

  1. Reinstall the fuel pump relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

CHECK AND REPLACE HARNESS OR CONNECTOR (EFI RELAY - CIRCUIT OPENING RELAY) 

10.INSPECT FUEL PUMP RELAY


    A030519
  1. Remove the fuel pump relay from the engine room R/B.

  1. Check the fuel pump relay resistance.

    Standard resistance:
    Tester Connections
    Specified Conditions
    3 - 4
    Below 1 Ω
    3 - 5
    10 kΩ or higher
    3 - 4
    10 kΩ or higher
    (when battery voltage applied to terminal 1 and 2)
    3 - 5
    Below 1 Ω
    (when battery voltage applied to terminal 1 and 2)

  1. Reinstall the fuel pump relay.



NG
REPLACE FUEL PUMP RELAY
OK


11.INSPECT FUEL PUMP RESISTOR (RESISTANCE)


    G035666E02
  1. Inspect the fuel pump resistor resistance.

    1. Measure the resistance.

      Standard resistance:
      0.70 to 0.76 Ω at 20°C (68°F)



NG
REPLACE FUEL PUMP RESISTOR
OK


12.CHECK HARNESS AND CONNECTOR (FUEL PUMP RELAY - FUEL PUMP)


    A138730E01
  1. Check the harness and connector between the fuel pump relay and fuel pump resistor.

    1. Remove the fuel pump relay from the engine room R/B.

    2. Disconnect the F8 fuel pump resistor connector.

    3. Check the resistance.

      Standard resistance (Check for open):
      Tester Connections
      Specified Conditions
      Fuel pump relay (5) - Fuel pump relay resistor (F8-1)
      Below 1 Ω

      Standard resistance (Check for short):
      Tester Connections
      Specified Conditions
      Fuel pump relay (5) - or Fuel pump resistor (F8-1) - Body ground
      10 kΩ or higher

    4. Reinstall the fuel pump relay

    5. Reconnect the fuel pump resistor connector.

  1. Check the harness and connector between the fuel pump resistor and fuel pump.

    1. Disconnect the F18 fuel pump resistor connector.

    2. Disconnect the F14 fuel pump connector.

    3. Check the resistance.

      Standard resistance (Check for open):
      Tester Connections
      Specified Conditions
      Fuel pump resistor (F8-2) - Fuel pump (F14-4)
      Below 1 Ω

      Standard resistance (Check for short):
      Tester Connections
      Specified Conditions
      Fuel pump resistor (F8-2) or Fuel pump (F14-4) - Body ground
      10 kΩ or higher

    4. Reconnect the fuel pump resistor connector.

    5. Reconnect the fuel pump connector.



OK
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE
NG

REPAIR OR REPLACE HARNESS OR CONNECTOR