Home › COMMUNICATION SYSTEM › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > TERMINALS OF ECU

for Preparation Click here


HINT:
This section describes the standard CAN values for all CAN related components.


CAN J/C


  1. CAN J/C connectors.

    HINT:
    1. The connectors connected to the CAN J/C can be distinguished by the colors of the bus lines and the connecting side of the connector.
    2. J48, J49, J50 and J51 are interchangeable.


    G038050E01


    CAN J/C connectors
    ("A" side, with earth terminal)
    Color (CAN-H Side)
    Color (CAN-L Side)
    ECM (J51)
    L
    LG
    DLC3 (J50)
    P
    V
    Steering angle sensor (J49)
    B
    Y
    Yaw rate sensor (J48)
    W
    R

    CAN J/C connectors
    ("B" side, without earth terminal)
    Color (CAN-H Side)
    Color (CAN-L Side)
    Skid control ECU (J47)
    B
    W



  2. G026205E12
  3. The terminals of the CAN J/C connectors.
    Terminal
    Terminal symbol
    1
    CANH
    2
    CANL



  4. G026214E16
  5. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Terminals
    Specified value
    CANH - CANL
    108 to 132 Ω


DLC3


    C123301E20
  1. Check DLC3.

    1. Measure the resistance according to the value(s) in the table below.

      Standard resistance:

      Terminals
      Terminal Description
      Condition
      Specified value
      D1-6 (CANH) - D1-14 (CANL)
      HIGH-level CAN bus line - LOW-level CAN bus line
      IG switch OFF, stop light switch OFF
      54 to 69 Ω
      D1-6 (CANH) - D1-16 (BAT)
      HIGH-level CAN bus line - Battery positive
      IG switch OFF, stop light switch OFF
      1 MΩ or higher
      D1-14 (CANL) - D1-16 (BAT)
      LOW-level CAN bus line - Battery positive
      IG switch OFF, stop light switch OFF
      1 MΩ or higher
      D1-6 (CANH) -D1-4 (CG)
      HIGH-level CAN bus line - Ground
      IG switch OFF, stop light switch OFF
      3 kΩ or higher
      D1-14 (CANL) - D1-4 (CG)
      LOW-level CAN bus line - Ground
      IG switch OFF, stop light switch OFF
      3 kΩ or higher


SKID CONTROL ECU


    E069126E54
  1. Check the skid control ECU harness side connector (S28).

    1. Disconnect the connector (S28) from the skid control ECU.

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance:

      Terminals
      Wiring Color
      Terminal Description
      Condition
      Specified value
      S28-11 (CANH) - S28-25 (CANL)
      B - W
      HIGH-level CAN bus line - LOW-level CAN bus line
      IG switch OFF, stop light switch OFF
      108 to 132 Ω
      S28-11 (CANH) - S28-32 (GND1)
      B - W-B
      HIGH-level CAN bus line - Ground
      IG switch OFF, stop light switch OFF
      3 kΩ or higher
      S28-25 (CANL) - S28-32 (GND1)
      W - W-B
      LOW-level CAN bus line - Ground
      IG switch OFF, stop light switch OFF
      3 kΩ or higher
      S28-11 (CANH) - S28-31 (+BS)
      B - Y
      HIGH-level CAN bus line - Battery positive
      IG switch OFF, stop light switch OFF
      1 MΩ or higher
      S28-25 (CANL) - S28-31 (+BS)
      W - Y
      LOW-level CAN bus line - Battery positive
      IG switch OFF, stop light switch OFF
      1 MΩ or higher


STEERING SENSOR


    G027814E06
  1. Check the harness side connector (S11) of the steering sensor.

    1. Disconnect the connector (S11) from the steering sensor.

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance:

      Terminals
      Wiring Color
      Terminal Description
      Condition
      Specified value
      S11-3 (CANH) - S11-11 (CANL)
      B - Y
      HIGH-level CAN bus line - LOW-level CAN bus line
      IG switch OFF, stop light switch OFF
      108 to 132 Ω
      S11-3 (CANH) - S11-2 (ESS)
      B - W-B
      HIGH-level CAN bus line - Ground
      IG switch OFF, stop light switch OFF
      3 kΩ or higher
      S11-11 (CANL) - S11-2 (ESS)
      Y - W-B
      LOW-level CAN bus line - Ground
      IG switch OFF, stop light switch OFF
      3 kΩ or higher
      S11-3 (CANH) - S11-9 (BAT)
      B - W-B
      HIGH-level CAN bus line - Battery positive
      IG switch OFF, stop light switch OFF
      1 MΩ or higher
      S11-11 (CANL) - S11-9 (BAT)
      Y - W-B
      LOW-level CAN bus line - Battery positive
      IG switch OFF, stop light switch OFF
      1 MΩ or higher


YAW RATE SENSOR


    G026641E18
  1. Check the yaw rate sensor harness side connector (Y1).

    1. Disconnect the connector (Y1) from the yaw rate sensor.

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance:

      Terminals
      Wiring Color
      Terminal Description
      Condition
      Specified value
      Y1-3 (CANH) - Y1-2 (CANL)
      Y - R
      HIGH-level CAN bus line - LOW-level CAN bus line
      IG switch OFF, stop light switch OFF
      54 to 69 Ω
      Y1-3 (CANH) - Y1-1 (GND)
      W - W-B
      LOW-level CAN bus line - Ground
      IG switch OFF, stop light switch OFF
      3 kΩ or higher
      Y1-2 (CANL) - Y1-1 (GND)
      R - W-B
      LOW-level CAN bus line - Ground
      IG switch OFF, stop light switch OFF
      3 kΩ or higher
      Y1-3 (CANH) - D1-16 (BAT)
      W - O
      LOW-level CAN bus line - Battery positive
      IG switch OFF, stop light switch OFF
      1 MΩ or higher
      Y1-2 (CANL) - D1-16 (BAT)
      R - O
      LOW-level CAN bus line - Battery positive
      IG switch OFF, stop light switch OFF
      1 MΩ or higher


ECM


  1. Measure the resistance according to the value(s) in the table below.


    G036662E14


    Standard resistance:

    Terminal
    Condition
    Specified Value
    E7-33 (CANH) - E7-34 (CANL)
    1. IG switch OFF
    2. Stop light switch OFF
    108 to 132 Ω



  2. G038049E01
  3. Measure the resistance according to the value(s) in the table below.

    Standard resistance:

    Terminals
    Wiring Color
    Condition
    Specified Value
    E7-33 (CANH) - E7-34 (CANL)
    L - LG
    1. IG switch OFF
    2. Stop light switch OFF
    108 to 132 Ω
    E7-33 (CANH) - E4-7 (E01)
    L - W-B (2UZ-FE)
    L - BR (1GR-FE)
    1. IG switch OFF
    2. Stop light switch OFF
    3 kΩ or higher
    E7-34 (CANL) - E4-7 (E01)
    LG - W-B (2UZ-FE)
    LG - BR (1GR-FE)
    1. IG switch OFF
    2. Stop light switch OFF
    3 kΩ or higher
    E7-33 (CANH) - E8-3 (BATT)
    L - L
    1. IG switch OFF
    2. Stop light switch OFF
    1 MΩ or higher
    E7-34 (CANL) - E8-3 (BATT)
    LG - L
    1. IG switch OFF
    2. Stop light switch OFF
    1 MΩ or higher