Home › SECURITIES › THEFT DETERRENT › THEFT DETERRENT SYSTEM

THEFT DETERRENT SYSTEM > SYSTEM DESCRIPTION



OUTLINE OF THEFT DETERRENT SYSTEM
  1. The theft deterrent system will operate when someone attempts to forcibly enter the vehicle, unlock any door or open the engine hood without using the key.
    This system causes the lights to light up or blink and the horns to sound in order to deter break-in and theft.
  2. The theft deterrent system has 2 modes; one is the active arming mode (see ACTIVE ARMING MODE) and the other is passive arming mode (see PASSIVE ARMING MODE). The passive arming mode can be switched ON/OFF using the specified method.
  3. Each mode has 4 states; a disarmed state, an arming preparation state, an armed state and an alarm sounding state.
  1. Disarmed state:

    1. The alarm function is not operating.
    2. The theft deterrent system is not operating.

  2. Arming preparation state:

    1. The time until the system goes into the armed state.
    2. The theft deterrent system is not operating.

  3. Armed state:

    1. The theft deterrent system is operating.

  4. Alarm sounding state:

    1. Alarm function is operating.

    Alarm time:
    (60 +- 5 sec.) x 10

    HINT:
    If the vehicle remains in a condition that sets off the alarm (any door remains open, engine hood remains open, ignition switch remains directly connected) after the alarm ends, the alarm will be set off repeatedly a maximum of 10 times for every one of the above specified conditions.


    Refer to table below for alarm method and time: 
    Alarm Method
    Headlight
    Blinking (cycle of 0.4 sec.)
    Taillight
    Blinking (cycle of 0.4 sec.)
    Hazard Warning Light
    Blinking (cycle of flasher relay)
    Interior Light
    Illuminating
    Vehicle Horn
    Sounding
    (approx. 0.4 second cycles)
    Security Horn
    Sounding
    (approx. 0.4 second cycles)
    Alarm Time
    Approx. 60 sec. (maximum 10 times)

    HINT:
    If any of the doors are unlocked when the key is not in the key cylinder during the armed state, a forced door lock signal will be output (see FORCED DOOR LOCK CONTROL).


ACTIVE ARMING MODE

HINT:
Active arming mode starts the alarm control immediately after the doors are locked.



  1. Active arming mode:
    This system activates as described in the diagram below when one of items for each condition is met.


    B112141E01


    Condition
    Item
    Condition (1)
    In the disarmed state, when the key is not in the key cylinder, the system state is switched if one of the following conditions is met.
    1. With all doors, engine hood closed, lock all doors by key operation.
    2. With all doors, engine hood closed, lock all doors by wireless operation.
    3. Lock all doors without using key and perform either of the following.
      1. Open any door or the engine hood and then close them all and lock all doors.
      2. Leave all doors locked and engine hood closed.
    Condition (2)
    1. After condition (1) is met, allow approx. 30 seconds to elapse.
    Condition (3)
    1. Unlock all doors by wireless operation.
    2. Unlock all doors by key operation.
    3. Unlock any door.
    4. Open any door.
    5. Open engine hood.
    6. Insert key into ignition key cylinder.
    7. Turn the ignition switch OFF to ON.
    8. Reconnect battery.
    Condition (4)
    1. Open engine hood.
    2. Reconnect battery.
    3. Open any door.
    4. Open any door without key and wireless operation.
    5. Directly connect ignition switch without key (or turn ignition switch ON without key).
    Condition (5)
    1. Insert key into ignition key cylinder, turn ignition switch ON and run engine over 550 rpm for 10 to 12 sec.
    2. Unlock all doors by wireless operation.
    3. Unlock all doors by key operation.
    4. Insert key into ignition key cylinder and turn ignition switch from OFF to ON.
    Condition (6)
    1. After approx. 60 seconds, alarm stops and system returns to armed state.


PASSIVE ARMING MODE

HINT:
  1. Passive arming mode starts the alarm control when the key is not in key cylinder and doors are closed.
  2. Passive arming mode can be switched ON/OFF by the specified method.
  3. The alarm is initially set (when shipped from factory) to active arming mode (not passive arming mode).
  4. During passive arming mode, the theft deterrent system goes into the armed state even if the doors are not locked.
  5. Detecting that the doors are unlocked does not set off the alarm during passive arming mode.
  6. A forced door lock signal is not output during passive arming mode (see FORCED DOOR LOCK CONTROL).
  7. Although the theft deterrent system detects that the doors are opened during passive arming mode, the alarm will not go off immediately because an entry delay time is set.
  8. If any of the following conditions is met during passive arming mode, the theft deterrent system will switch to active arming mode.
    1. With all doors and engine hood closed, lock all doors by key operation.
    2. With all doors and engine hood closed, lock all doors by wireless operation.
    3. Lock all doors without using key and perform either of the following.
      Open any door or the engine hood and then close them all and lock all doors. / Leave all doors locked and engine hood closed.



  1. Passive arming mode:
    This system activates as described in the diagram below when one of items for each condition is met.


    B125108E01

    HINT:
    1. *1: Disarmed state 1 is the normal disarmed state.
    2. *2: Disarmed state 2 is set from either the disarmed state 1 or the arming preparation state.


    Condition
    Item
    Condition (1)
    1. With ignition switch OFF, open any door and pull the key out of the ignition key cylinder.
    2. With ignition switch OFF, pull the key out of the ignition key cylinder and open any door.
    Condition (2)
    1. With engine hood closed, close all doors..
    2. With engine hood and all doors closed, close back door.
    Condition (3)
    1. Unlock all doors by wireless operation.
    2. Unlock all doors by key operation.
    3. Reconnect battery.
    4. Insert key into ignition key cylinder.
    5. Turn the ignition switch from OFF to ON.
    Condition (4)
    1. After condition (1) is met, allow approx. 30 seconds to elapse.
    Condition (5)
    1. Open any door.
    2. Open engine hood.
    3. Open back door.
    Condition (6)
    1. Open any door and allow entry delay time*1 to elapse.
    2. Open engine hood.
    3. Reconnect battery.
    4. Turn the ignition switch ON without using key.
    Condition (7)
    1. Unlock all doors by wireless operation.
    2. Unlock all doors by key operation.
    3. Insert key into ignition key cylinder and turn ignition switch from OFF to ON.
    Condition (8)
    1. After approx. 60 sec., alarm stops and system returns to armed state.

    HINT:
    *1: When any door is opened while all the doors are closed during passive arming mode, the entry delay time starts. If the switch condition (armed state → disarmed state 1 or 2) is met during the entry delay time, the theft deterrent system will return to disarmed state 1 or 2. However, if the switch condition for disarmed state 1 or 2 is not met, the theft deterrent system will recognize it as a theft and set off the alarm. Entry delay time of 0, 14 or 30 sec. can be selected by the customizing function.


PROCEDURE FOR CHANGING OF PASSIVE MODE (ON OR OFF)

E112668E04


E112669E01

HINT:
  1. Initial mode is PASSIVE MODE OFF.
  2. If the ignition switch is turned ON, change will be cancelled.
  3. * Entry delay time.


FORCED DOOR LOCK CONTROL
  1. The forced door lock control prevents the vehicle from being tampered with. Immediately after a door is unlocked (alarm starts), the door is forced to lock by a forced door lock signal.

    1. Conditions that force the doors to lock:
      When the key is not in the key cylinder and 0.4 seconds have elapsed after the previous output of a forced door lock signal, the doors will be forced to lock if any of the following conditions is met:

      1. The theft deterrent system is in the alarm sounding state of active arming mode.
      2. Any door is unlocked.


ALARM MEMORY FUNCTION
  1. If the alarm is set off (tampering is detected) while the theft deterrent system is armed, it will be recorded by the alarm memory function. Whenever the theft deterrent system is cancelled, the alarm memory function causes the taillights to light up for 2 seconds in order to inform you that the alarm has been set off.

    1. Conditions of the alarm memory function that cause the taillights to light up:
      When the theft deterrent system has entered into the alarm sounding state (tampering has been detected) even once, the taillights will light up for 2 seconds if any of the following conditions is met.

      1. Switched to the disarmed state from the armed state during active arming mode.
      2. Switched to the disarmed state 1 from the armed state during passive arming mode.
      3. Switched to the disarmed state (2) from the armed state during passive mode.

      HINT:
      Active arming mode: See ACTIVE ARMING MODE.

      Passive arming mode: See PASSIVE ARMING MODE.


PANIC ALARM CONTROL
  1. The panic alarm control makes it possible to voluntarily set off the panic alarm by pressing the PANIC (LOCK) switch on the wireless transmitter.

    1. Conditions that cause the panic alarm control to set off the panic alarm:
      The panic alarm control sets off the panic alarm by pressing the PANIC (LOCK) switch on the wireless transmitter over 2.4 seconds under the following conditions:

      1. The ignition switch is OFF.
      2. The theft deterrent system is not in the alarm sounding state. (This condition is common both to active arming mode and to passive arming mode.)

    2. Conditions that cause the panic alarm control to shut off the alarm:
      The panic alarm control shuts off the panic alarm when any of the following conditions is met during panic alarm operation:

      1. The ignition switch is ON.
      2. Either of the switches on the wireless transmitter (LOCK/UNLOCK) is pressed.
      3. The panic alarm ends (approx. 60 sec. have passed).
      4. The theft deterrent system switches to the alarm sounding state. Under this condition, the theft deterrent system is controlling the alarm rather than the panic alarm control. In order to cancel this alarm, refer to the theft deterrent system alarm sounding state cancellation procedure. (This condition is common both to active arming mode to passive arming mode.)

      HINT:
      Active arming mode: See ACTIVE ARMING MODE.
      Passive arming mode: See PASSIVE ARMING MODE.


SECURITY INDICATOR OUTPUT
  1. The theft warning ECU outputs a signal to light up the security indicator, according to the state of the theft deterrent system. However, some of the actual lighting conditions of the security indicator are different from the output signals of the theft warning ECU.

    Output: 
    State of Theft Deterrent System*
    Security Indicator
    Output Signals from Theft warning ECU
    Actual Lighting Condition
    Disarmed state 1, 2
    OFF
    OFF (Immobiliser system unset)
    BLINKING (Immobiliser system set)
    Arming preparation state
    ON
    ON
    Armed state
    OFF
    BLINKING
    Alarm sounding state
    ON
    ON
    Blinking cycle: 
    Time
    Security Indicator
    0.2 sec.
    ON
    1.8 sec.
    OFF

    HINT:
    1. *: The above condition is common both to active arming mode and to passive arming mode.
    2. When the immobiliser system is set, the security indicator blinks during both the disarmed state and the armed state, due to the output signals from the immobiliser system.