Home › STEERING › POWER STEERING › VANE PUMP

VANE PUMP > INSTALLATION

for Preparation Click here



1. INSTALL VANE PUMP ASSEMBLY


    F042722
  1. Using a "torx" socket (E10), install the vane pump with the stud bolt.

    Torque:
    22 N*m{ 224 kgf*cm , 16 ft.*lbf }

  1. Install the 2 bolts and nut.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }



2. INSTALL VANE PUMP V BELT


    EM06656
  1. Loosen the belt tension by turning the belt tensioner counterclockwise, and install the bolt.



3. CONNECT PRESSURE FEED TUBE ASSEMBLY


    F042721
  1. Install the union bolt with a new gasket on each side of the tube.

    Torque:
    51 N*m{ 520 kgf*cm , 38 ft.*lbf }



4. CONNECT OIL RESERVOIR TO PUMP HOSE NO. 1


    F042720
  1. Install the hose with the clip.



    F042719
  1. Install the 2 hoses with the 2 clips.



5. INSTALL AIR CLEANER ASSEMBLY


6. ADD POWER STEERING FLUID


    F040898
  1. Keep the vehicle horizontal.

  1. With the engine stopped, check the fluid level in the reservoir.
    If necessary, add fluid.

    Fluid:
    ATF DEXRON II or III

    HINT:
    If the fluid is hot, check that the fluid level is within the HOT range. If the fluid is cold, check that the fluid level is within the COLD range.

  1. Start the engine and run at idle.

  1. Turn the steering wheel from lock to lock several times to raise fluid temperature.

    Fluid temperature:
    75 to 80°C (167 to 176°F)



    F040897E07
  1. Check for foaming or emulsification.
    If foaming or emulsification is identified, bleed the power steering system.



    R011786E08
  1. With the engine idling, measure the fluid level in the reservoir.

  1. Stop the engine.

  1. Wait a few minutes and remeasure the fluid level in the reservoir.

    Maximum fluid level rise:
    About 5 mm (0.20 in.)

    If a problem is found, bleed the power steering system.

  1. Check the fluid level.



7. BLEED POWER STEERING FLUID
  1. Check the fluid level.

  1. Jack up the front of the vehicle and support it with stands.

  1. Turn the steering wheel.

    1. With the engine stopped, turn the wheel slowly from lock to lock several times.

  1. Lower the vehicle.

  1. Start the engine.

    1. Run the engine at idle for a few minutes.

  1. Turn the steering wheel.

    1. With the engine idling, turn the wheel left or right to the full lock position and keep it there for 2 to 3 seconds, then turn the wheel to the opposite full lock position and keep it there for 2 to 3 seconds.*1

    2. Repeat (*1) several times.

  1. Stop the engine.



    F040897E06
  1. Check for foaming or emulsification.
    Especially, if the system has to be held twice because of foaming or emulsification, check for fluid leaks in the system.

  1. Check the fluid level.



8. INSPECT POWER STEERING FLUID LEAK
  1. Check the fluid level.

  1. Jack up the front of the vehicle and support it with stands.

  1. Turn the steering wheel.

    1. With the engine stopped, turn the wheel slowly from lock to lock several times.

  1. Lower the vehicle.

  1. Start the engine.

    1. Run the engine at idle for a few minutes.

  1. Turn the steering wheel.

    1. With the engine idling, turn the wheel left or right to the full lock position and keep it there for 2 to 3 seconds, then turn the wheel to the opposite full lock position and keep it there for 2 to 3 seconds.*1

    2. Repeat (*1) several times.

  1. Stop the engine.



    F040897E06
  1. Check for foaming or emulsification.
    Especially, if the system has to be held twice because of foaming or emulsification, check for fluid leaks in the system.

  1. Check the fluid level.