Home › ENGINE ยท 2UZ-FE › EMISSION CONTROL › AIR PUMP

AIR PUMP > REMOVAL

for Preparation Click here



1. DISCHARGE FUEL SYSTEM PRESSURE


2. DRAIN ENGINE COOLANT

CAUTION:
To avoid the danger of being burned, do not remove the radiator cap while the engine and radiator are still hot. Thermal expansion will cause hot engine coolant and steam to blow out from the radiator.

  1. Remove the radiator cap.



    A070279E01
  1. Remove the service hole cover from the engine under cover No. 1.

  1. Install a vinyl hose onto the drain on the radiator side.

  1. Fix the vinyl hose with tape.



    A070477E01
  1. Loosen the 3 drain plugs on the engine and radiator, and drain the coolant.

  1. Drain the coolant from the reservoir tank.

  1. Tighten the 3 drain plugs.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf } for the engine

  1. Remove the vinyl hose from the radiator.



3. REMOVE THROTTLE BODY COVER SUB-ASSEMBLY
  1. Remove the 2 nuts and throttle body cover sub-assembly.



4. REMOVE AIR CLEANER HOSE ASSEMBLY
  1. Disconnect the vacuum hoses (for the P/S idle-up and fuel pressure regulator) and ventilation hose.

  1. Remove the air cleaner hose assembly.



5. DISCONNECT FUEL HOSE


    A066659
  1. Remove the pulsation damper and 2 gaskets.

  1. Disconnect the No. 1 fuel hose.



6. DISCONNECT FUEL NO. 2 HOSE


7. DISCONNECT CONNECTORS FROM INTAKE MANIFOLD
  1. Disconnect the throttle control connector.

  1. Disconnect the VSV connector for EVAP.

  1. Disconnect the 8 injector connectors.

  1. Disconnect the ECT sensor connector.

  1. Disconnect the 2 VSV connectors for the air injection system.

  1. Disconnect the 8 ignition coil connectors.

  1. Disconnect the 2 air fuel ratio sensor connectors.



8. DISCONNECT HOSES FROM INTAKE MANIFOLD


    A134405E01
  1. Disconnect the vacuum hose [A] from the fuel pressure regulator.

  1. Disconnect the PCV hoses [B] from the PCV valve on the LH cylinder head.

  1. Disconnect the EVAP hose (from the charcoal canister) [C] from the VSV for the EVAP.

  1. Disconnect the 2 vacuum hoses [D] from the VSV for the air injection system.



9. REMOVE INTAKE MANIFOLD ASSEMBLY


    A133761E01
  1. Disconnect the 2 water by-pass hoses from the throttle body.



    A133763
  1. Disconnect the 2 wire clamps from the wire clamp bracket on the RH delivery pipe.



    A133764
  1. Remove the bolt and nut holding the engine wire protector from the intake manifold and cylinder head.

  1. Remove the 2 bolts and ground cables from the RH and LH cylinder heads.

  1. Remove the bolt and V-bank cover bracket from the intake manifold.



    A133765
  1. Disconnect the engine wire from the engine hanger and wire bracket.



    A133766
  1. Remove the bolt and wire bracket from the intake manifold.

  1. Remove the 6 bolts, 4 nuts, intake manifold assembly and 2 gaskets.



10. REMOVE WATER BY-PASS PIPE SUB-ASSEMBLY
  1. Remove the bolt and water by-pass pipe.



11. REMOVE AIR PUMP ASSEMBLY WITH BRACKET


    A133809
  1. Disconnect the No.2 air hose from the air switching valve.

  1. Disconnect the air switching valve connector.

  1. Disconnect the pressure sensor connector for the air injection system.

  1. Remove the 4 bolts and air pump with bracket assembly.



12. REMOVE AIR PUMP ASSEMBLY


    A133810
  1. Remove the 3 bolts and air pump assembly.

  1. Remove the 3 insulators from the air pump assembly.