Home › DRIVE LINE ยท PROPELLER SHAFT › PROPELLER SHAFT ASSEMBLY (for 4WD)

PROPELLER SHAFT ASSEMBLY (for 4WD) > REASSEMBLY

for Preparation Click here



1. INSTALL REAR PROPELLER SHAFT UNIVERSAL JOINT SPIDER BEARING


    C060598
  1. Apply MP grease No. 2 to a new spider and bearings.

  1. Fit the spider into the flange yoke.



    C063061E04
  1. Using SST, install the bearings on the spider.

    SST
    09332-25010  

  1. Using SST, adjust both bearings so that the snap ring grooves are at maximum and equal in width.

    SST
    09332-25010  



    G020755
  1. Install new 4 snap rings of equal thickness which will allow no axial play.

    HINT:
    Do not reuse the snap rings.
    Thickness of snap ring (Both ends thin type) 
    Parts No.
    Thickness mm (in.)
    Mark
    90520-25039
    2.28 to 2.30
    1
    90520-25040
    2.30 to 2.32
    2
    90520-25041
    2.32 to 2.34
    -
    90520-25042
    2.34 to 2.36
    Brown
    90520-25043
    2.36 to 2.38
    Blue
    90520-25044
    2.38 to 2.40
    6
    90520-25045
    2.40 to 2.42
    7
    90520-25046
    2.42 to 2.44
    8
    90520-25047
    2.44 to 2.46
    C139333
    90520-25048
    2.46 to 2.48
    10
    90520-25049
    2.48 to 2.50
    A
    90520-25050
    2.50 to 2.52
    B
    90520-25051
    2.52 to 2.54
    C
    90520-25052
    2.54 to 2.56
    D
    90520-25053
    2.56 to 2.58
    E
    90520-25054
    2.18 to 2.20
    J
    90520-25055
    2.20 to 2.22
    K
    90520-25056
    2.22 to 2.24
    F
    90520-25057
    2.24 to 2.26
    G
    90520-25058
    2.26 to 2.28
    H

    NOTICE:
    1. Must use a new retainer ring.
    2. Must use retainer rings of the same thickness as possible on both ends.

  1. Using a hammer, tap the yoke until there is no clearance between the spider bearing outer race and snap ring.

    HINT:
    Install a new spider bearing on the sleeve side in the procedure described above.



2. INSTALL REAR PROPELLER SHAFT SLIDING SHAFT DUST COVER SUB-ASSEMBLY


    D003049E01
  1. Using SST and press, press in a new dust cover.

    NOTICE:
    Place the universal joint straight when pressing in the dust cover. Apply MP grease to the "A" part.



3. INSTALL RR PROPELLER SHAFT UNIVERSAL JOINT SLEEVE YOKE SUB-ASSEMBLY


    G022296E02
  1. Install the grease fitting to the universal joint sleeve yoke.

  1. Apply MP grease to the propeller shaft spline and sleeve yoke sliding surface.

  1. Align the matchmarks on the sleeve yoke propeller shaft.

  1. Install the propeller shaft into the sleeve yoke.



4. INSPECT REAR PROPELLER SHAFT UNIVERSAL JOINT SPIDER BEARING


5. INSPECT PROPELLER SHAFT ASSEMBLY


HINT:
When replacing the spider bearing, be sure that the grease fitting assembly hole is facing to the direction shown in the illustration.



G022300E02