Home › RESTRAINTS › SEAT BELT › REAR SEAT OUTER BELT ASSEMBLY (for Rear No. 1 Seat)

REAR SEAT OUTER BELT ASSEMBLY (for Rear No. 1 Seat) > INSTALLATION

for Preparation Click here


HINT:
Use the same procedures for the LH and RH.



1. INSTALL 3 POINT TYPE BELT ASSEMBLY RH (with Rear No. 2 Seat)


    B065024E01
  1. Check the degree of tilt when the belt begins to lock the ELR.

    NOTICE:
    Do not disassemble the retractor.

  1. Check the amount of inclination required to lock the retractor.

    1. When the inclination of the retractor is 15°or less, check that the belt can be pulled from the retractor. When the inclination of the retractor is over 45°, check that the belt locks.
      If operation is not as specified, replace the belt assembly.

  1. Install the rear seat belt inner with the bolt.

    Torque:
    42 N*m{ 430 kgf*cm , 31 ft.*lbf }

  1. Install the seat shoulder belt cover.

  1. Install the seatback board RH.

  1. Install the belt on the retractor side with the 4 nuts.

    Torque:
    42 N*m{ 430 kgf*cm , 31 ft.*lbf }

  1. Install the belt LH on the floor anchor side with the bolt.

    Torque:
    42 N*m{ 430 kgf*cm , 31 ft.*lbf }

  1. Check the ELR lock.

    NOTICE:
    The check should be performed with the outer belt assembly installed.


    1. With the belt installed, check that the belt locks when it is pulled out quickly.
      If operation is not as specified, replace the belt assembly.

  1. Check the fastening function of the child restraint system.

    NOTICE:
    The check should be performed with the outer belt assembly installed.


    1. When the belt is pulled out fully, the belt should automatically try to retract.

    2. After the belt has fully retracted, the belt should be able to be pulled out and retract again.
      If operation is not as specified, replace the belt assembly.



2. REMOVE 3 POINT TYPE BELT ASSEMBLY LH (without Rear No. 2 Seat)


    B065025E01
  1. Check the degree of tilt when the belt begins to lock the ELR.

    NOTICE:
    Do not disassemble the retractor.

  1. Check the amount of inclination required to lock the retractor.

    1. When the inclination of the retractor is 15° or less, check that the belt can be pulled from the retractor. When the inclination of the retractor is over 45°, check that the belt locks.
      If operation is not as specified, replace the belt assembly.

  1. Install the rear seat 3 point type belt inner with the bolt.

    Torque:
    42 N*m{ 430 kgf*cm , 31 ft.*lbf }

  1. Install the belt assembly on the retractor side with the 2 bolts.

    Torque:
    for upper bolt:
    8.5 N*m{ 87 kgf*cm , 75 ft.*lbf }
    for lower bolt:
    42 N*m{ 430 kgf*cm , 31 ft.*lbf }

  1. 3rd seat type:
    Install the No. 2 seat belt outer RH on the shoulder anchor side with the bolt.

    Torque:
    42 N*m{ 430 kgf*cm , 31 ft.*lbf }

  1. Install the roof side garnish inner RH.

  1. Install the deck trim side panel RH.

  1. Install the belt outer on the floor anchor side with the bolt.

    Torque:
    42 N*m{ 430 kgf*cm , 31 ft.*lbf }

  1. 3rd seat type:
    Install the No. 2 seat belt outer RH on the floor anchor side with the bolt.

  1. Install the floor anchor cover.

  1. 3rd seat type:
    Install the floor anchor cover.

  1. Check the ELR lock.

    NOTICE:
    The check should be performed with the outer belt assembly installed.


    1. With the belt installed, check that the belt locks when it is pulled out quickly.
      If operation is not as specified, replace the belt assembly.

  1. Check fastening function of the child restraint system.

    NOTICE:
    The check should be performed with the outer belt assembly installed.


    1. When the belt is pulled out fully, the belt should automatically try to retract.

    2. After the belt has fully retracted, the belt should be able to be pulled out and retract again.
      If operation is not as specified, replace the belt assembly.



3. INSTALL ROOF SIDE GARNISH ASSEMBLY INNER RH (with Rear No. 2 Seat)


4. INSTALL ROOF SIDE GARNISH INNER RH


5. INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH (with Rear No. 2 Seat)


6. INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH


7. INSTALL REAR FLOOR CARPET ASSEMBLY


8. INSTALL DECK TRIM COVER REAR


9. INSTALL REAR DOOR WEATHERSTRIP RH


10. INSTALL REAR DOOR SCUFF PLATE RH


11. INSTALL QUARTER SCUFF PLATE INNER RH (with Rear No. 2 Seat)


12. INSTALL SIDE TRIM BOX ASSEMBLY RH


13. INSTALL DECK TRIM SIDE BOARD UPR RH


14. INSTALL DECK TRIM COVER REAR


15. INSTALL DECK FLOOR BOX RH


16. INSTALL REAR FLOOR MAT SUPPORT PLATE REAR


17. INSTALL DECK BOARD ASSEMBLY (without Rear No. 2 Seat)


18. INSTALL DECK BOARD SUB-ASSEMBLY (without Rear No. 2 Seat)


19. INSTALL BACK DOOR GLASS WEATHERSTRIP


20. INSTALL REAR NO. 2 SEAT LOCK ASSEMBLY RH (with Rear No. 2 Seat)


21. INSTALL NO. 2 SEAT LEG COVER (with Rear No. 2 Seat)


22. INSTALL REAR NO. 2 SEAT ASSEMBLY RH (with Rear No. 2 Seat)


23. INSTALL REAR NO. 2 SEAT ASSEMBLY LH (with Rear No. 2 Seat)


24. INSTALL TONNEAU COVER RETRACTOR SUB-ASSEMBLY