Home › STEERING › STEERING COLUMN › STEERING COLUMN ASSEMBLY

STEERING COLUMN ASSEMBLY > INSTALLATION

for Preparation Click here



1. INSTALL STEERING COLUMN ASSEMBLY
  1. Install the steering column assembly with the steering intermediate shaft assembly with the 4 steering column set nuts.

    Torque:
    26 N*m{ 270 kgf*cm , 20 ft.*lbf }

  1. Connect the wire harness to the steering column assembly.

  1. Connect each of the connectors to the steering column assembly.



2. INSTALL STEERING COLUMN HOLE COVER


    G021461
  1. Install the steering column hole cover with the 4 clips.

  1. Install the heater to register duct to the heater unit.



3. INSTALL STEERING INTERMEDIATE SHAFT SUB-ASSEMBLY NO. 2


    F043317E02
  1. Align the matchmarks on the power steering gear and steering intermediate shaft sub-assembly No. 2.

  1. Install the steering intermediate shaft sub-assembly No. 2 to the steering gear box with the bolt C.

    Torque:
    Bolt C:
    36 N*m{ 360 kgf*cm , 27 ft.*lbf }



4. INSTALL STEERING SLIDING YOKE
  1. Align the matchmarks on the steering column and steering sliding yoke.

  1. Install the steering sliding yoke to the steering column assembly and slide it upward.

  1. Align the matchmarks on the intermediate shaft sub-assembly No. 2 and steering sliding yoke.

  1. Install the sliding yoke to the intermediate shaft sub-assembly No. 2 with the bolt A and bolt B.

    Torque:
    Bolt A, B:
    36 N*m{ 360 kgf*cm , 27 ft.*lbf }



5. INSTALL ENGINE UNDER COVER ASSEMBLY REAR
  1. Install the engine under cover assembly rear with the 4 bolts.

    Torque:
    29 N*m{ 300 kgf*cm , 22 ft.*lbf }



6. INSTALL ENGINE UNDER COVER SUB-ASSEMBLY NO. 1
  1. Install the engine under cover sub-assembly No. 1 with the 4 bolts.

    Torque:
    29 N*m{ 300 kgf*cm , 22 ft.*lbf }



7. INSTALL TURN SIGNAL SWITCH ASSEMBLY


    F043318
  1. Install the turn signal switch assembly with the 3 screws.

  1. Connect the 3 connectors to the turn signal switch assembly.



8. INSTALL SPIRAL CABLE


    H042178
  1. Check that the front wheels are facing straight ahead.

  1. Turn the spiral cable counterclockwise by hand until it becomes harder to turn.

  1. Then rotate the spiral cable clockwise about 2.5 turns to align the mark.

    HINT:
    The spiral cable will rotate about 2.5 turns to either left or right of the center.

  1. Install the spiral cable with the 4 screws.

  1. Connect the 2 connectors to the spiral cable.



9. INSTALL STEERING COLUMN COVER UPR


    F043298
  1. Install the steering column cover upper to the steering column assembly.



10. INSTALL STEERING COLUMN COVER LWR
  1. Install the steering column cover lower to the steering column assembly.

  1. Install the 3 screws to the steering column cover upper and lower.



11. INSTALL INSTRUMENT PANEL LOWER LH


12. INSTALL INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY LOWER


13. INSTALL COWL SIDE TRIM BOARD LH


14. INSTALL FRONT FLOOR FOOT REST


15. INSTALL FRONT DOOR SCUFF PLATE LH


16. INSTALL STEERING WHEEL ASSEMBLY
  1. Align the matchmarks on the steering wheel and main shaft assembly.

  1. Install the steering set nut.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }

  1. without Steering pad switch:
    Connect the connector.



17. INSTALL STEERING PAD

NOTICE:
  1. Never use airbag parts from another vehicle. When replacing parts, replace with new ones.
  2. Make sure the steering pad is installed to the specified torque.
  3. If the steering pad has been dropped, or there are cracks, dents or other defects in the case or connector, replace the steering pad with a new one.
  4. When installing the steering pad, take care that the wirings do not interfere with other parts and they are not pinched between other parts.



    F043297E01
  1. Connect the horn ground harness to the steering pad.

  1. Connect the 2 airbag connectors.

  1. Install the steering pad after confirming that the circumference groove of "torx" screw is caught on the screw case.

  1. Using a "torx" socket wrench ("Torx" socket wrench (T=30)), torque the 2 screws.

    Torque:
    8.8 N*m{ 90 kgf*cm , 78 in.*lbf }



18. INSTALL STEERING WHEEL COVER LOWER NO. 2


19. INSTALL STEERING WHEEL COVER LOWER NO. 3


20. PLACE FRONT WHEELS FACING STRAIGHT AHEAD


21. CONNECT BATTERY NEGATIVE TERMINAL


22. INSPECT SRS WARNING LIGHT

HINT:
Click here.