Home › STEERING › STEERING COLUMN › STEERING COLUMN ASSEMBLY

STEERING COLUMN ASSEMBLY > REMOVAL

for Preparation Click here



1. PRECAUTION

HINT:
Click here.



2. DISCONNECT BATTERY NEGATIVE TERMINAL


3. PLACE FRONT WHEELS FACING STRAIGHT AHEAD


4. REMOVE STEERING WHEEL COVER LOWER NO. 3


5. REMOVE STEERING WHEEL COVER LOWER NO. 2


6. REMOVE STEERING PAD

NOTICE:
If the airbag connector is disconnected with the ignition switch being at ON, DTCs will be recorded.



    F043322E01
  1. Using a "torx" socket wrench ("Torx" socket wrench (T=30)), loosen the 2 "torx" screws until the groove along the screw circumference catches on the screw case.



    F043321E01
  1. Pull out the steering pad from the steering wheel assembly.

    NOTICE:
    When removing the steering pad, take care not to pull the airbag wire harness.

  1. Using a screwdriver, release the lock part of each of the airbag connectors and disconnect the 2 airbag connectors.

  1. Disconnect the horn ground harness from the steering pad.



    F043311E01
  1. Remove the steering pad.

    CAUTION:
    1. When storing the steering pad, keep the upper surface of the pad facing upward.
    2. Never disassemble the steering pad.



7. REMOVE STEERING WHEEL ASSEMBLY


    F043320E01
  1. without Steering pad switch:
    Disconnect the connector.

  1. Remove the steering wheel assembly set nut.

  1. Mark matchmarks on the steering wheel assembly and main shaft assembly.

  1. Set the SST on the steering wheel assembly.

  1. Holding the SST to the monkey spanner and turn the SST, then remove the steering wheel assembly.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05021)



8. REMOVE FRONT DOOR SCUFF PLATE LH


9. REMOVE FRONT FLOOR FOOT REST


10. REMOVE COWL SIDE TRIM BOARD LH


11. REMOVE INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY LOWER


    B062738E01
  1. Remove the 2 bolts <B>.

  1. Disconnect the hood lock control cable assembly and fuel lid lock control cable sub-assembly.

  1. Disengage the 4 clips.

  1. Disconnect the connectors and remove the lower instrument panel finish panel sub-assembly.



12. REMOVE INSTRUMENT PANEL LOWER LH


13. REMOVE STEERING COLUMN COVER LWR


    F043298
  1. Remove the 3 screws and steering column cover lower.



14. REMOVE STEERING COLUMN COVER UPR


15. REMOVE SPIRAL CABLE


    H042178
  1. Disconnect the 2 connectors.

  1. Remove the 4 screws and spiral cable.



16. REMOVE TURN SIGNAL SWITCH ASSEMBLY


    F043318
  1. Disconnect the 3 connectors.

  1. Remove the 3 screws and turn signal switch assembly.



17. REMOVE ENGINE UNDER COVER SUB-ASSEMBLY NO. 1
  1. Remove the 4 bolts and engine under cover sub-assembly No. 1.



18. REMOVE ENGINE UNDER COVER ASSEMBLY REAR
  1. Remove the 4 bolts and engine under cover assembly rear.



19. REMOVE STEERING SLIDING YOKE


    F043317E02
  1. Mark matchmarks on the steering sliding yoke, steering intermediate shaft sub-assembly No. 2 and steering intermediate shaft assembly.

  1. Remove the bolt A and bolt B from the steering sliding yoke.

  1. Slide the steering sliding yoke up and separate it from the steering intermediate shaft sub-assembly No. 2.

  1. Pull down the steering sliding yoke from the steering intermediate shaft assembly to remove.



20. REMOVE STEERING INTERMEDIATE SHAFT SUB-ASSEMBLY NO. 2
  1. Mark matchmarks on the power steering gear assembly and steering intermediate shaft sub-assembly No. 2.

  1. Remove the bolt C and intermediate shaft sub-assembly No. 2 from the power steering gear assembly.



21. REMOVE STEERING COLUMN HOLE COVER


    F043316E01
  1. Remove the heater to register duct.

  1. Remove the 4 clips and steering column hole cover.



22. REMOVE STEERING COLUMN ASSEMBLY
  1. Disconnect each of the connectors from the steering column assembly.

  1. Disconnect the wire harness from the steering column assembly.

  1. Remove the 4 steering column set nuts.

  1. Pull out the steering column assembly with the intermediate shaft assembly.