Home › STEERING › STEERING COLUMN › STEERING COLUMN ASSEMBLY

STEERING COLUMN ASSEMBLY > REASSEMBLY

for Preparation Click here



1. INSTALL KEY INTER LOCK SOLENOID
  1. Install the key inter lock solenoid to the steering column bracket assembly upper with 2 screws.



2. INSTALL IGNITION OR STARTER SWITCH ASSEMBLY
  1. Install the ignition or starter switch assembly to the steering column bracket assembly upper with 2 screws.



3. INSTALL UN-LOCK WARNING SWITCH ASSEMBLY


    C090812
  1. Install the un-lock warning switch assembly to the steering column bracket assembly upper.

  1. Connect the un-lock warning switch assembly connector to the ignition or starter switch assembly.



4. INSTALL IGNITION SWITCH LOCK CYLINDER & KEY SET
  1. Make sure that the ignition switch lock cylinder assembly is at the ACC position.

  1. Install the ignition switch lock cylinder assembly.



5. INSTALL TRANSPONDER KEY AMPLIFIER

NOTICE:
Take care not to push the amplifier up with excessive force to prevent it from being damaged.



    C090697
  1. Align the transponder key amplifier with the installation position of the upper bracket with the amplifier inclined.

  1. Push up the transponder key amplifier and connect it to the upper bracket.



6. INSPECT STEERING LOCK OPERATION
  1. Check that the steering mechanism is activated when removing the key.

  1. Check that the steering mechanism is deactivated when inserting the key and turning it to ACC position.



7. INSTALL STEERING ENERGY ABSORBING PLATE GUIDE


8. INSTALL STEERING COLUMN ENERGY ABSORBING PLATE


9. INSTALL STEERING ENERGY ABSORBING PIN SUB-ASSEMBLY


10. INSTALL STEERING MAIN SHAFT ASSEMBLY


    C090850
  1. Install the compression spring, bearing thrust collar and bearing to the No. 1 main shaft.

  1. Temporarily install the steering column tube sub-assembly upper to the No. 1 main shaft.



    H041541E01
  1. Secure the No. 1 main shaft with the steering column tube sub-assembly upper and SST in a vise.

    SST
    09316-60011   (09316-00051)



    H041542E01
  1. Using SST, compress the spring of the steering column tube sub-assembly upper.

    SST
    09950-40011   (09951-04010, 09952-04010, 09953-04020, 09954-04010, 09955-04061, 09958-04011)

    NOTICE:
    Do not overtighten the SST.



    H041543
  1. Using a snap ring expander, install a new snap ring to the main shaft.



    C092889
  1. Assemble the No.1 main shaft with the steering column tube sub-assembly upper and No. 2 main shaft sub-assembly.



    C090875
  1. Using a hexagon wrench (6 mm), install the 2 tilt steering bolts.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. Install the main shaft with the steering column tube sub-assembly upper to the column tube.



    F043306
  1. Tilt & telescopic steering:
    Install the steering column No. 1 ring to the steering main shaft.



    F043307E01
  1. Using SST, install the tension spring.

    SST
    09921-00010  

  1. Install the turn signal bracket with the 2 bolts.

    Torque:
    5.7 N*m{ 58 kgf*cm , 50 in.*lbf }



    F043308
  1. Install the steering column protector with the 2 bolts.

    Torque:
    6 N*m{ 60 kgf*cm , 52 in.*lbf }



    H041540E01
  1. Using SST, install the 2 tension springs.

    SST
    09921-00010  



11. INSTALL STEERING COLUMN BRACKET ASSEMBLY UPPER (w/ Tilt and Telescopic Steering)


    C090694
  1. Temporarily install the lock wedge, steering column bracket assembly upper and steering column upper clamp with the 2 new tapered-head bolts.

  1. Tighten the 2 tapered-head bolts until the bolt heads break off.



    F043301
  1. Make the telescopic mechanism most extended condition.

  1. After tightening the telescopic lever bolt, perform the loosening procedure at least 5 times to stabilize.

    Torque:
    Tighten:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }
    Loosen:
    0 N*m{ 0 kgf*cm , 0 ft.*lbf }

  1. Fix the telescopic lever bolt.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf }

  1. Install the telescopic lever on the position where the telescopic locks.

  1. Fix the telescopic lever to the steering column assembly with a inverse nut.

    Torque:
    23 N*m{ 240 kgf*cm , 17 ft.*lbf }



    F043310
  1. Install the inverse nut on the steering telescopic lever.

    Torque:
    23 N*m{ 240 kgf*cm , 17 ft.*lbf }



12. INSTALL STEERING COLUMN BRACKET ASSEMBLY UPPER (w/ Tilt Steering)


    C090694
  1. Temporarily install the steering column bracket assembly upper and steering column upper clamp with the 2 new tapered-head bolts.

  1. Tighten the 2 tapered-head bolts until the bolt heads break off.



13. INSTALL STEERING INTERMEDIATE SHAFT ASSEMBLY


    F043315E01
  1. Align the matchmarks on the steering column assembly and the steering intermediate shaft assembly.

  1. Install the steering intermediate shaft assembly and thrust stopper to the steering column assembly with the bolt.

    Torque:
    36 N*m{ 360 kgf*cm , 27 ft.*lbf }