Home › COMMUNICATION SYSTEM › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > Check CAN Bus Lines for Short Circuit

for Preparation Click here


DESCRIPTION

The CAN bus lines are considered to be shorted when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 54 Ω.

Symptom
Trouble Area
Resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 54 Ω.
  1. Short in CAN bus lines
  2. Skid control ECU
  3. Steering angle sensor
  4. Yaw rate sensor
  5. ECM
  6. CAN J/C

WIRING DIAGRAM


G036694E01


INSPECTION PROCEDURE

1.CHECK CAN BUS LINES FOR SHORT CIRCUIT (DLC3 SUB BUS LINE)


    G031933E33
  1. Disconnect the DLC3 sub bus line connector (J50) from the CAN J/C.

    NOTICE:
    1. Before disconnecting the connector, make a note of where it is connected.
    2. Reconnect the connector to its original position.



    G026206E73
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester connection
    Condition
    Specified value
    D1-6 (CANH) - D1-14 (CANL)
    1. IG switch OFF
    2. Stop light switch OFF
    1 MΩ or more



NG
REPAIR OR REPLACE DLC3 SUB BUS LINE OR CONNECTOR (CAN-H, CAN-L)
OK


2.CONNECT CONNECTOR
  1. Reconnect the DLC3 sub bus line connector (J50) to the CAN J/C.


NEXT


3.CHECK CAN BUS LINES FOR SHORT CIRCUIT (SKID CONTROL ECU SUB BUS LINE)


    G031932E97
  1. Disconnect the skid control ECU sub bus line connector (J47) from the CAN J/C.

    NOTICE:
    1. Before disconnecting the connector, make a note of where it is connected.
    2. Reconnect the connector to its original position.



    G026206E73
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester connection
    Condition
    Specified value
    D1-6 (CANH) - D1-14 (CANL)
    1. IG switch OFF
    2. Stop light switch OFF
    54 to 69 Ω



OK
Go to step 10
NG


4.CONNECT CONNECTOR
  1. Reconnect the skid control ECU sub bus line connector (J47) to the CAN J/C.


NEXT


5.CHECK CAN BUS LINES FOR SHORT CIRCUIT (YAW RATE SENSOR SUB BUS LINE)


    G031933E34
  1. Disconnect the yaw rate sensor sub bus line connector (J48) from the CAN J/C.

    NOTICE:
    1. Before disconnecting the connector, make a note of where it is connected.
    2. Reconnect the connector to its original position.



    G026206E73
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester connection
    Condition
    Specified value
    D1-6 (CANH) - D1-14 (CANL)
    1. IG switch OFF
    2. Stop light switch OFF
    54 to 69 Ω



OK
Go to step 12
NG


6.CONNECT CONNECTOR
  1. Reconnect the yaw rate sensor sub bus line connector (J48) to the CAN J/C.


NEXT


7.CHECK CAN BUS LINES FOR SHORT CIRCUIT (STEERING ANGLE SENSOR SUB BUS LINE)


    G031933E35
  1. Disconnect the steering angle sensor sub bus line connector (J49) from the CAN J/C.

    NOTICE:
    1. Before disconnecting the connector, make a note of where it is connected.
    2. Reconnect the connector to its original position.



    G026206E73
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester connection
    Condition
    Specified value
    D1-6 (CANH) - D1-14 (CANL)
    1. IG switch OFF
    2. Stop light switch OFF
    54 to 69 Ω



OK
Go to step 14
NG


8.CONNECT CONNECTOR
  1. Reconnect the steering angle sensor sub bus line connector (J49) to the CAN J/C.


NEXT


9.CHECK CAN BUS LINES FOR SHORT CIRCUIT (ECM MAIN BUS LINE)


    G031933E32
  1. Disconnect the ECM main bus line connector (J51) from the CAN J/C.

    NOTICE:
    1. Before disconnecting the connector, make a note of where it is connected.
    2. Reconnect the connector to its original position.



    G026206E73
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester connection
    Condition
    Specified value
    D1-6 (CANH) - D1-14 (CANL)
    1. IG switch OFF
    2. Stop light switch OFF
    108 to 132 Ω



OK
Go to step 16
NG

REPLACE CAN J/C 

10.CONNECT CONNECTOR
  1. Reconnect the skid control ECU sub bus line connector (J47) to the CAN J/C.


NEXT


11.CHECK CAN BUS LINES FOR SHORT CIRCUIT (SKID CONTROL ECU SUB BUS LINE)


    G026206E73
  1. Disconnect the skid control ECU connector (S28).

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester connection
    Condition
    Specified value
    D1-6 (CANH) - D1-14 (CANL)
    1. IG switch OFF
    2. Stop light switch OFF
    54 to 69 Ω



OK
REPLACE MASTER CYLINDER SOLENOID
NG

REPAIR OR REPLACE SKID CONTROL ECU SUB BUS LINE OR CONNECTOR (CAN-H, CAN-L) 

12.CONNECT CONNECTOR
  1. Reconnect the yaw rate sensor sub bus line connector (J48) to the CAN J/C.


NEXT


13.CHECK CAN BUS LINES FOR SHORT CIRCUIT (YAW RATE SENSOR SUB BUS LINE)


    G026206E73
  1. Disconnect the yaw rate sensor connector (Y1).

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester connection
    Condition
    Specified value
    D1-6 (CANH) - D1-14 (CANL)
    1. IG switch OFF
    2. Stop light switch OFF
    54 to 69 Ω



OK
REPLACE YAW RATE SENSOR
NG

REPAIR OR REPLACE YAW RATE SENSOR SUB BUS LINE OR CONNECTOR 

14.CONNECT CONNECTOR
  1. Reconnect the steering angle sensor sub bus line connector (J49) to the CAN J/C.


NEXT


15.CHECK CAN BUS LINES FOR SHORT CIRCUIT (STEERING ANGLE SENSOR SUB BUS LINE)


    G026206E73
  1. Disconnect the steering angle sensor connector (S11).

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester connection
    Condition
    Specified value
    D1-6 (CANH) - D1-14 (CANL)
    1. IG switch OFF
    2. Stop light switch OFF
    54 to 69 Ω



OK
REPLACE STEERING ANGLE SENSOR
NG

REPAIR OR REPLACE STEERING ANGLE SENSOR SUB BUS LINE OR CONNECTOR (CAN-H, CAN-L) 

16.CONNECT CONNECTOR
  1. Reconnect the ECM main bus line connector (J51) to the CAN J/C.


NEXT


17.CHECK CAN BUS LINES FOR SHORT CIRCUIT (ECM MAIN BUS LINE)


    G026206E73
  1. Disconnect the ECM connector (E7).

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester connection
    Condition
    Specified value
    D1-6 (CANH) - D1-14 (CANL)
    1. IG switch OFF
    2. Stop light switch OFF
    108 to 132 Ω



OK
REPLACE ECM
NG

REPAIR OR REPLACE ECM MAIN BUS LINE OR CONNECTOR (CAN-H, CAN-L)