Home › COMMUNICATION SYSTEM › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > Open in One Side of CAN Sub Bus Line

for Preparation Click here


DESCRIPTION

If 2 or more ECUs and/or sensors do not appear on the intelligent tester's "BUS CHECK" screen via the CAN VIM, one side of the CAN sub-bus line may be open. (One side of the CAN-H [sub-bus line]/CAN-L [sub-bus line] of the ECU and/or sensor is open.)

Symptom
Trouble Area
2 or more ECUs and/or sensors do not appear on the intelligent tester's "BUS CHECK" screen via the CAN VIM.
  1. One side of the CAN sub-bus line is open
  2. Skid control ECU
  3. Steering angle sensor
  4. Yaw rate sensor
  5. ECM
  6. CAN J/C

WIRING DIAGRAM


G036694E01


INSPECTION PROCEDURE

1.CHECK OPEN IN ONE SIDE OF CAN SUB BUS LINE (SKID CONTROL ECU SUB BUS LINE)


    G031932E98
  1. Disconnect the skid control ECU sub bus line connector (J47) from the CAN J/C.

    NOTICE:
    1. Before disconnecting the connector, make a note of where it is connected.
    2. Reconnect the connector to its original position.

  1. Connect the intelligent tester via the CAN VIM to the DLC3.

  1. Turn the ignition switch ON.

  1. Select "BUS CHECK" on the intelligent tester display via the CAN VIM (Click here).

    Result:
    Proceed to
    Result
    A
    "ABS/VSC/TRAC" does not appear
    B
    2 or more ECUs and/or sensors do not appear



A
Go to step 8
B


2.CONNECT CONNECTOR
  1. Reconnect the skid control ECU sub bus line connector (J47) to the CAN J/C.


NEXT


3.CHECK OPEN IN ONE SIDE OF CAN SUB BUS LINE (STEERING ANGLE SENSOR SUB BUS LINE)


    G031933E35
  1. Disconnect the steering angle sensor sub bus line connector (J49) from the CAN J/C.

    NOTICE:
    1. Before disconnecting the connector, make a note of where it is connected.
    2. Reconnect the connector to its original position.

  1. Connect the intelligent tester via the CAN VIM to the DLC3.

  1. Turn the ignition switch ON.

  1. Select "BUS CHECK" on the intelligent tester display via the CAN VIM (Click here).

    Result:
    Proceed to
    Result
    A
    "STEERING SENSOR" does not appear
    B
    2 or more ECUs and/or sensors do not appear



A
Go to step 10
B


4.CONNECT CONNECTOR
  1. Reconnect the steering angle sensor sub bus line connector (J49) to the CAN J/C.


NEXT


5.CHECK OPEN IN ONE SIDE OF CAN SUB BUS LINE (YAW RATE SENSOR SUB BUS LINE)


    G031933E34
  1. Disconnect the yaw rate sensor sub bus line connector (J48) from the CAN J/C.

    NOTICE:
    1. Before disconnecting the connector, make a note of where it is connected.
    2. Reconnect the connector to its original position.

  1. Connect the intelligent tester via the CAN VIM to the DLC3.

  1. Turn the ignition switch ON.

  1. Select "BUS CHECK" on the intelligent tester display via the CAN VIM (Click here).

    Result:
    Proceed to
    Result
    A
    "YAW /DECELERAT" does not appear
    B
    2 or more ECUs and/or sensors do not appear



B
Go to step 12
A


6.CONNECT CONNECTOR
  1. Reconnect the yaw rate sensor sub bus line connector (J48) to the CAN J/C.


NEXT


7.CHECK OPEN IN ONE SIDE OF CAN BUS LINE (YAW RATE SENSOR SUB BUS LINE)


    G026359E63
  1. Disconnect the yaw rate sensor connector (Y1).

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester connection
    Condition
    Specified value
    Y1-2 (CANL) - Y1-3 (CANH)
    1. IG switch OFF
    2. Stop light switch OFF
    54 to 69 Ω



NG
REPAIR OR REPLACE YAW RATE SENSOR SUB BUS LINE OR CONNECTOR (CAN-H, CAN-L)
OK

REPLACE YAW RATE SENSOR 

8.CONNECT CONNECTOR
  1. Reconnect the skid control ECU sub bus line connector (J47) to the CAN J/C.


NEXT


9.CHECK OPEN IN ONE SIDE OF CAN SUB BUS LINE (SKID CONTROL ECU SUB BUS LINE)


    E069126E55
  1. Disconnect the skid control ECU connector (S28).

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester connection
    Condition
    Specified value
    S28-11 (CANH) - S28-25 (CANL)
    1. IG switch OFF
    2. Stop light switch OFF
    54 to 69 Ω



NG
REPAIR OR REPLACE SKID CONTROL ECU SUB BUS LINE OR CONNECTOR (CAN-H, CAN-L)
OK

REPLACE MASTER CYLINDER SOLENOID 

10.CONNECT CONNECTOR
  1. Reconnect the steering angle sensor sub bus line connector (J49) to the CAN J/C.


NEXT


11.CHECK OPEN IN ONE SIDE OF CAN SUB BUS LINE (STEERING ANGLE SENSOR SUB BUS LINE)


    G027814E07
  1. Disconnect the steering angle sensor connector (S11).

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester connection
    Condition
    Specified value
    S11-3 (CANH) - S11-11 (CANL)
    1. IG switch OFF
    2. Stop light switch OFF
    54 to 69 Ω



NG
REPAIR OR REPLACE STEERING ANGLE SENSOR SUB BUS LINE OR CONNECTOR (CAN-H, CAN-L)
OK

REPLACE STEERING ANGLE SENSOR 

12.CHECK CAN J/C


    G026214E16
  1. Disconnect connectors (J47), (J48), (J49), (J50) and (J51) from the CAN J/C.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester connection
    Condition
    Specified value
    1 (CANH) - 2 (CANL)
    1. IG switch OFF
    2. Stop light switch OFF
    108 to 132 Ω



NG
REPLACE CAN J/C
OK

REPLACE ECM