Home › COMMUNICATION SYSTEM › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > Check CAN Bus Line for Short to +B

for Preparation Click here


DESCRIPTION

A short to +B is suspected in the CAN bus line when there is continuity between terminals 16 (BAT) and 6 (CANH) or terminals 16 (BAT) and 14 (CANL) of the DLC3.

Symptom
Trouble Area
There is continuity between terminals 16 (BAT) and 6 (CANH) or 16 (BAT) and 14 (CANL) of the DLC3.
  1. Short to +B in CAN bus line
  2. ECM
  3. Skid control ECU
  4. Steering angle sensor
  5. Yaw rate sensor

WIRING DIAGRAM


G036695E01


INSPECTION PROCEDURE

1.CHECK CAN BUS LINE FOR SHORT TO +B (DLC3 SUB BUS LINE)


    G031933E33
  1. Disconnect the DLC3 sub bus line connector (J50) from the CAN J/C.

    NOTICE:
    1. Before disconnecting the connector, make a note of where it is connected.
    2. Reconnect the connector to its original position.



    G026206E74
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester connection
    Condition
    Specified value
    D1-16 (BAT) - D1-6 (CANH)
    1. IG switch OFF
    2. Stop light switch OFF
    1 MΩ or higher
    D1-16 (BAT) - D1-14 (CANL)
    1. IG switch OFF
    2. Stop light switch OFF
    1 MΩ or higher



NG
REPAIR OR REPLACE DLC3 SUB BUS LINE OR CONNECTOR (CAN-H, CAN-L)
OK


2.CONNECT CONNECTOR
  1. Reconnect the DLC3 sub bus line connector (J50) to the CAN J/C.


NEXT


3.CHECK CAN BUS LINE FOR SHORT TO +B (SKID CONTROL ECU SUB BUS LINE)


    G031932E97
  1. Disconnect the skid control ECU sub bus line connector (J47) from the CAN J/C.

    NOTICE:
    1. Before disconnecting the connector, make a note of where it is connected.
    2. Reconnect the connector to its original position.



    G026206E74
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester connection
    Condition
    Specified value
    D1-16 (BAT) - D1-6 (CANH)
    1. IG switch OFF
    2. Stop light switch OFF
    1 MΩ or higher
    D1-16 (BAT) - D1-14 (CANL)
    1. IG switch OFF
    2. Stop light switch OFF
    1 MΩ or higher



OK
Go to step 10
NG


4.CONNECT CONNECTOR
  1. Reconnect the skid control ECU sub bus line connector (J47) to the CAN J/C.


NEXT


5.CHECK CAN BUS LINE FOR SHORT TO +B (YAW RATE SENSOR SUB BUS LINE)


    G031933E34
  1. Disconnect the yaw rate sensor sub bus line connector (J48) from the CAN J/C.

    NOTICE:
    1. Before disconnecting the connector, make a note of where it is connected.
    2. Reconnect the connector to its original position.



    G026206E74
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester connection
    Condition
    Specified value
    D1-16 (BAT) - D1-6 (CANH)
    1. IG switch OFF
    2. Stop light switch OFF
    1 MΩ or higher
    D1-16 (BAT) - D1-14 (CANL)
    1. IG switch OFF
    2. Stop light switch OFF
    1 MΩ or higher



OK
Go to step 12
NG


6.CONNECT CONNECTOR
  1. Reconnect the yaw rate sensor sub bus line connector (J48) to the CAN J/C.


NEXT


7.CHECK CAN BUS LINE FOR SHORT TO +B (STEERING ANGLE SENSOR SUB BUS LINE)


    G031933E35
  1. Disconnect the steering angle sensor sub bus line connector (J49) from the CAN J/C.

    NOTICE:
    1. Before disconnecting the connector, make a note of where it is connected.
    2. Reconnect the connector to its original position.



    G026206E74
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester connection
    Condition
    Specified value
    D1-16 (BAT) - D1-6 (CANH)
    1. IG switch OFF
    2. Stop light switch OFF
    1 MΩ or higher
    D1-16 (BAT) - D1-14 (CANL)
    1. IG switch OFF
    2. Stop light switch OFF
    1 MΩ or higher



OK
Go to step 14
NG


8.CONNECT CONNECTOR
  1. Reconnect the steering angle sensor sub bus line connector (J49) to the CAN J/C.


NEXT


9.CHECK CAN BUS LINE FOR SHORT TO +B (ECM MAIN BUS LINE)


    G026206E74
  1. Disconnect the ECM connector (E7).

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester connection
    Condition
    Specified value
    D1-16 (BAT) - D1-6 (CANH)
    1. IG switch OFF
    2. Stop light switch OFF
    1 MΩ or higher
    D1-16 (BAT) - D1-14 (CANL)
    1. IG switch OFF
    2. Stop light switch OFF
    1 MΩ or higher



OK
REPLACE ECM
NG

REPAIR OR REPLACE ECM MAIN BUS LINE OR CONNECTOR (CAN-H, CAN-L) 

10.CONNECT CONNECTOR
  1. Reconnect the skid control ECU sub bus line connector (J47) to the CAN J/C.


NEXT


11.CHECK CAN BUS LINE FOR SHORT TO +B (SKID CONTROL ECU SUB BUS LINE)


    G026206E74
  1. Disconnect the skid control ECU connector (S28).

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester connection
    Condition
    Specified value
    D1-16 (BAT) - D1-6 (CANH)
    1. IG switch OFF
    2. Stop light switch OFF
    1 MΩ or higher
    D1-16 (BAT) - D1-14 (CANL)
    1. IG switch OFF
    2. Stop light switch OFF
    1 MΩ or higher



OK
REPLACE MASTER CYLINDER SOLENOID
NG

REPAIR OR REPLACE SKID CONTROL ECU SUB BUS LINE OR CONNECTOR (CAN-H, CAN-L) 

12.CONNECT CONNECTOR
  1. Reconnect the yaw rate sensor sub bus line connector (J48) to the CAN J/C.


NEXT


13.CHECK CAN BUS LINE FOR SHORT TO +B (YAW RATE SENSOR SUB BUS LINE)


    G026206E74
  1. Disconnect the yaw rate sensor connector (Y1).

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester connection
    Condition
    Specified value
    D1-16 (BAT) - D1-6 (CANH)
    1. IG switch OFF
    2. Stop light switch OFF
    1 MΩ or higher
    D1-16 (BAT) - D1-14 (CANL)
    1. IG switch OFF
    2. Stop light switch OFF
    1 MΩ or higher



OK
REPLACE YAW RATE SENSOR
NG

REPAIR OR REPLACE YAW RATE SENSOR SUB BUS LINE OR CONNECTOR (CAN-H, CAN-L) 

14.CONNECT CONNECTOR
  1. Reconnect the steering angle sensor sub bus line connector (J49) to the CAN J/C.


NEXT


15.CHECK CAN BUS LINE FOR SHORT TO +B (STEERING ANGLE SENSOR SUB BUS LINE)


    G026206E74
  1. Disconnect the steering angle sensor connector (S11).

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester connection
    Condition
    Specified value
    D1-16 (BAT) - D1-6 (CANH)
    1. IG switch OFF
    2. Stop light switch OFF
    1 MΩ or higher
    D1-16 (BAT) - D1-14 (CANL)
    1. IG switch OFF
    2. Stop light switch OFF
    1 MΩ or higher



OK
REPLACE STEERING ANGLE SENSOR
NG

REPAIR OR REPLACE STEERING ANGLE SENSOR SUB BUS LINE OR CONNECTOR (CAN-H, CAN-L)