Home › BODY › ENGINE HOOD / DOOR › FRONT DOOR

FRONT DOOR > DISASSEMBLY

for Preparation Click here


HINT:
  1. Use the same procedures for the RH side and LH side.
  2. The procedures listed below are for the LH side.
  3. A bolt without a torque specification is shown in the standard bolt chart .



1. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH LH


    B062415E01
  1. Using a screwdriver, remove the lower frame bracket garnish.

    HINT:
    Tape the screwdriver tip before use.



2. REMOVE FRONT DOOR INSIDE HANDLE BEZEL LH


    B062416E02
  1. Using a screwdriver, disengage the 3 claws, and remove the inside handle bezel.

    HINT:
    Tape the screwdriver tip before use.



3. REMOVE FRONT ARMREST ASSEMBLY LH


    B062417E01
  1. Disengage the claws, and remove the armrest from the trim board.

    HINT:
    Tape the screwdriver tip before use.



4. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH


    B062418E01
  1. Remove the 2 cushion rubbers.

  1. Remove the 2 screws and clips.

  1. Using a clip remover, remove the 11 clips.

  1. Remove the trim board upward.

    HINT:
    In order to prevent the door from being damaged, cover the parts indicated by arrow marks in the illustration with tape.



    H006127E01
  1. Disconnect the 2 cables from the inside handle as shown in the illustration.

  1. Remove the inner weatherstrip.

  1. Remove the 3 screws and power window master switch.



    B064057E01
  1. Using a screwdriver, disengage the 4 claws.

    HINT:
    Tape the screwdriver tip before use.

  1. Remove the power mirror switch, as shown in the illustration.



5. REMOVE FRONT DOOR SERVICE HOLE COVER LH


    B065760E01
  1. Remove the front door service hole cover LH.

    NOTICE:
    Remove the remaining tape on the door side.



6. REMOVE OUTER REAR VIEW MIRROR ASSEMBLY LH


    B062419
  1. Disconnect the outer rear view mirror connector.

  1. Remove the 3 nuts and outer rear view mirror.

    NOTICE:
    When the nuts are removed, the outer rear view mirror might drop and be deformed.



7. REMOVE FRONT NO. 1 SPEAKER ASSEMBLY


    I031482
  1. Disconnect the connector.

  1. Remove the 4 screws and front No. 1 speaker.



8. REMOVE FRONT NO. 2 SPEAKER ASSEMBLY


    B062421
  1. Disconnect the speaker connector.

  1. Remove the 2 bolts and No. 2 speaker.

  1. Remove the 2 bolts and speaker mounting No. 1 bracket.



9. REMOVE FRONT DOOR WINDOW FRAME MOULDING REAR LH


    B065259E01
  1. Remove the screw.

  1. Using a heat light, heat the moulding to 40 to 60°C (104 to 140°F).

    NOTICE:
    Do not heat the moulding excessively.

  1. Disengage the 2 claws by pushing the moulding and remove the moulding.

    NOTICE:
    If reusing the moulding, take care not to damage the moulding.



10. REMOVE FRONT DOOR GLASS WEATHERSTRIP ASSEMBLY OUTER LH


    B062951E01
  1. Put protective tape under the glass weatherstrip assembly.

  1. Remove the screw.

  1. Using a screwdriver or moulding remover, disengage the claw and remove the glass weatherstrip.

    HINT:
    Tape the screwdriver tip before use.



11. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY LH

HINT:
Insert a shop rag inside the door panel to prevent the glass from being scratched.



    B062422
  1. Open the door glass until the bolts appear in the service holes.

  1. Remove the 2 bolts and holding the door glass.



    B062423E12
  1. Remove the door glass, as shown in the illustration.

    NOTICE:
    1. Do not damage the door glass.
    2. When the bolts are removed, the door glass might drop and be deformed.

  1. Remove the door glass run.



12. REMOVE FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY LH


    B062424
  1. Disconnect the window regulator connector.

  1. Remove the 6 bolts and window regulator.

    NOTICE:
    When the bolts are removed, the window regulator might drop and be deformed.

    HINT:
    Remove the window regulator through the service hole.



13. REMOVE POWER WINDOW REGULATOR MOTOR ASSEMBLY LH
  1. Place matchmarks on the window regulator motor gear and regulator gear.

  1. Using a "torx" driver (T25), remove the 3 screws and window regulator motor.



14. REMOVE FRONT DOOR FRAME SUB-ASSEMBLY REAR LOWER LH


    B062425E01
  1. Remove the bolt and frame rear lower.



15. REMOVE FRONT DOOR OUTSIDE HANDLE COVER LH


    B061438E22
  1. Remove the hole plug.

  1. Using a "torx" socket wrench (T30), loosen the screw and remove the outside handle cover with the door lock key cylinder installed.



16. REMOVE FRONT DOOR W/MOTOR LOCK ASSEMBLY LH


    B062426
  1. Disconnect the door lock connector.

  1. Using a "torx" socket wrench (T30), remove the 3 screws and door lock.

    HINT:
    Remove the door lock through the service hole.

  1. Remove the door lock wire harness packing.



17. REMOVE FRONT DOOR HANDLE ASSEMBLY OUTSIDE LH


    B056613E13
  1. Pushing and pulling the outside handle in the arrow mark direction in the illustration, remove the outside handle.

  1. Remove the outside handle pad front and rear.



18. REMOVE FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY LH


    B062427E01
  1. Using a "torx" socket wrench (T30), loosen the screw.

  1. Slide the outside handle frame from to remove it.

    HINT:
    Remove the outside handle frame through the service hole.



19. REMOVE FRONT DOOR LOCK CHECK ASSEMBLY LH


    B062429
  1. Remove the 2 nuts, bolt and the door check.



20. REMOVE FRONT DOOR WEATHERSTRIP LH
  1. Using a clip remover, disengage the clips and remove the weatherstrip.

    HINT:
    If the clips are damaged, exchange them for new clips.



21. REMOVE FRONT DOOR WIRE LH


    B062428
  1. Disconnect the door wire clips.

  1. Remove the 2 bolts and door wire.