Home › SUSPENSION & AXLE › TIRE AND WHEEL › TIRE PRESSURE WARNING SYSTEM

DTC    C2111/11    Transmitter ID1 Operation Stop

DTC    C2112/12    Transmitter ID2 Operation Stop

DTC    C2113/13    Transmitter ID3 Operation Stop

DTC    C2114/14    Transmitter ID4 Operation Stop

DTC    C2115/15    Transmitter ID5 Operation Stop

for Preparation Click here


DESCRIPTION

The tire pressure monitor valve sub-assembly stops transmitting signals when receiving specific signals. The ECU stores the DTC when the tire pressure monitor valve sub-assembly receives the signals, for some reason, and stops transmitting signals. As this is not a system malfunction, the DTC is erased when signal transmission is resumed.

HINT:
The electric wave is stopped at assembly plant, because the strength of the electric wave emitting from the tire pressure sensing transmitter does not comply with the Japan Wireless Telegraphy Act.


DTC No.
DTC Detecting Condition
Trouble Area
C2111/11
C2112/12
C2113/13
C2114/14
C2115/15
When any signal similar to the stop signal is received for some reason, this DTC will be output.
  1. Tire pressure monitor valve sub-assembly
  2. Tire pressure monitor receiver assembly
  3. Tire pressure monitor ECU

HINT:
It is necessary to perform the procedure to identify the tire pressure monitor valve sub-assembly that is malfunctioning because it cannot be identified by the output DTC.


INSPECTION PROCEDURE

HINT:
Set the tire pressure to the specified value.

1.FORCIBLY TRANSMIT TRANSMITTER ID (ALL WHEELS)
  1. Remove the valve cores of the wheels to rapidly reduce the pressure of all tires to 120 kPa (1.2 kgf/cm2, 17 psi respectively).

    HINT:
    The transmitter ID can be transmitted forcibly by rapidly reducing tire air pressure.


NEXT


2.CHECK DTC
  1. Check for DTC.

    OK:
    DTC is not output.



OK
SET TIRE PRESSURE TO NORMAL VALUE (TRANSMITTER STOP CONDITION IS COMPLETELY RESET)
NG


3.SET TIRE PRESSURE TO NORMAL VALUE (NORMAL VALUE)
  1. Set the tire pressure back to the specified normal value.

    Front
    Rear
    Spare
    220 kPa (2.2 kgf/cm2, 32 psi)
    220 kPa (2.2 kgf/cm2, 32 psi)
    220 kPa (2.2 kgf/cm2, 32 psi)


NEXT


4.FORCIBLY TRANSMIT TRANSMITTER ID
  1. Forcibly transmit the transmitter ID by performing the following: Set the tire pressure to the specified value and rotate the tire 90 to 270 degrees. Rapidly reduce the tire pressure of all wheels.

    NOTICE:
    Rapidly reduce the pressure of all tires respectively.


NEXT


5.CHECK DTC
  1. Check for DTC.

    OK:
    DTC is not output.

    HINT:
    In the case of NG, system error is probable. Perform troubleshooting according to other DTC.



OK
SET TIRE PRESSURE TO NORMAL VALUE (TRANSMITTER STOP CONDITION IS COMPLETELY RESET)
NG


6.CHECK DTC
  1. Check if DTCs C2121/21, C2122/22, C2123/23, C2124/24 and C2125/25 are all output.



NO
Go to step 9
YES


7.CHECK HARNESS AND CONNECTOR (TIRE PRESSURE WARNING RECEIVER - TIRE PRESSURE WARNING ECU)


    F045860E01
  1. Disconnect the tire pressure monitor receiver assembly T17 connector and tire pressure monitor ECU T16 connector.



    F045861E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Specified Condition
    T16-7 (RDA) - T17-1 (RDA)
    Below 1 Ω
    T16-8 (RF5V) - T17-5 (+5V)
    Below 1 Ω
    T16-16 (GND2) - T17-4 (GND)
    Below 1 Ω
    T16-7 (RDA) - Body ground
    10 kΩ or higher
    T16-8 (RF5V) - Body ground
    10 kΩ or higher
    T16-16 (GND2) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8.CHECK TIRE PRESSURE WARNING ECU


    F045868E01
  1. Connect the tire pressure monitor ECU T16 connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Specified Condition
    T16-8 (RF5V) - T16-16 (GND2)
    4.5 to 5.5 V



NG
GO TO POWER SOURCE CIRCUIT
OK

REPLACE TIRE PRESSURE WARNING RECEIVER 

9.SET TIRE PRESSURE TO NORMAL VALUE
  1. Set the tire pressure of all wheels to the specified value.

    Front
    Rear
    Spare
    220 kPa (2.2 kgf/cm2, 32 psi)
    220 kPa (2.2 kgf/cm2, 32 psi)
    220 kPa (2.2 kgf/cm2, 32 psi)


NEXT


10.IDENTIFY TRANSMITTER CORRESPONDING TO DTC

HINT:
Refer to "Error in Present while Identifying Transmitter" (Click here).


NEXT


11.INTERCHANGE TIRES

HINT:
In the case where "A" (left front) is identified at step 10.



    F046785E01
  1. Interchange tire "A" for the identified tire pressure monitor valve sub-assembly with tire "B" for a normal one.


NEXT


12.SET TIRE PRESSURE TO NORMAL VALUE
  1. Set the tire pressure of all wheels to the specified value.

    Front
    Rear
    Spare
    220 kPa (2.2 kgf/cm2, 32 psi)
    220 kPa (2.2 kgf/cm2, 32 psi)
    220 kPa (2.2 kgf/cm2, 32 psi)


NEXT


13.FORCIBLY TRANSMIT TRANSMITTER ID


    F046786E01
  1. Remove the valve core of the tire "A", rapidly reduce the tire pressure and forcibly transmit the transmitter ID of the tire pressure monitor valve sub-assembly.


NEXT


14.CHECK DTC
  1. Check for DTC.

    OK:
    DTC is not output

    HINT:
    1. If a DTC is output, replace the identified tire pressure monitor valve sub-assembly.
    2. Register the transmitter ID after replacing and then set the tire pressure to the specified value.



NG
REPLACE TIRE PRESSURE WARNING VALVE AND TRANSMITTER
OK

REPLACE TIRE PRESSURE WARNING RECEIVER