Home › SUSPENSION & AXLE › TIRE AND WHEEL › TIRE PRESSURE WARNING SYSTEM

TIRE PRESSURE WARNING SYSTEM > Error in Past When Identifying Transmitter

for Preparation Click here


DESCRIPTION

HINT:
  1. Refer to "Error in Present While Identifying Transmitter" if the DTC is output currently. Refer to "Error in Past When Identifying Transmitter" if a previously output DTC is not output now. Even when DTCs C2165/65 to C2169/69 output both present and past codes, refer to "Error in Past When Identifying Transmitter".
  2. DTCs relevant to the transmitters are corresponding to each transmitter ID. It is impossible to identify which tire is malfunctioning according to each transmitter ID. Therefore the following procedure must be done to confirm the ID No. and tire location.
  3. The following is the procedure to identify which wheel's transmitter the ID1 is resulting from when assuming that either of the DTCs C2141/41 (Transmitter ID1 error) or C2165/65 (Abnormal temperature inside ID1 tire) is detected. Identify the corresponding transmitter using the same procedure when DTCs C2141/42 to C2145/45, C2166/66 to C2169/69 are detected.


INSPECTION PROCEDURE

1.SET TIRE PRESSURE TO NORMAL VALUE

Front
Rear
Spare
220 kPa (2.2 kgf*cm2, 32 psi)
220 kPa (2.2 kgf*cm2, 32 psi)
220 kPa (2.2 kgf*cm2, 32 psi)

NEXT


2.RAPIDLY REDUCE TIRE PRESSURE OF FRONT RIGHT WHEEL
  1. Rapidly reduce the pressure to 120 kPa (1.2 kgf*cm2, 17 psi).


NEXT


3.READ VALUE OF INTELLIGENT TESTER
  1. Using the intelligent tester, check ID1 data of the tire pressurel.


NEXT


4.CONFIRM VALUE OF ID1 TIRE PRESSURE
  1. Confirm the value of the ID1 tire pressure was set to 120 kPa (1.2 kgf*cm2, 17 psi).

    Result:
    Result
    Proceed to
    The front right wheel is set to value above.
    A
    Except front right wheel is set to value above.
    B



A
ID1 IS FOR FRONT RIGHT WHEEL TRANSMITTER
B


5.RAPIDLY REDUCE TIRE PRESSURE OF FRONT LEFT WHEEL
  1. Rapidly reduce the pressure to 120 kPa (1.2 kgf*cm2, 17 psi).


NEXT


6.READ VALUE OF INTELLIGENT TESTER
  1. Using the intelligent tester, check ID1 data of the tire pressure.


NEXT


7.CONFIRM VALUE OF ID1 TIRE PRESSURE
  1. Confirm the value of the ID1 tire pressure was set to 120 kPa (1.2 kgf*cm2, 17 psi).

    Result:
    Result
    Proceed to
    The front left wheel is set to value above.
    A
    Except front left wheel is set to value above.
    B



A
ID1 IS FOR FRONT LEFT WHEEL TRANSMITTER
B


8.RAPIDLY REDUCE TIRE PRESSURE OF REAR RIGHT WHEEL
  1. Rapidly reduce the pressure to 120 kPa (1.2 kgf*cm2, 17 psi).


NEXT


9.READ VALUE OF INTELLIGENT TESTER
  1. Using the intelligent tester, check ID1 data of the tire pressure.


NEXT


10.CONFIRM VALUE OF ID1 TIRE PRESSURE
  1. Check the value of the ID1 tire pressure was set to 120 kPa (1.2 kgf*cm2, 17 psi).

    Result:
    Result
    Proceed to
    The rear right wheel is set to value above.
    A
    Except rear right wheel is set to value above.
    B



A
ID1 IS FOR REAR RIGHT WHEEL TRANSMITTER
B


11.RAPIDLY REDUCE TIRE PRESSURE OF REAR LEFT WHEEL
  1. Rapidly reduce the pressure to 120 kPa (1.2 kgf*cm2, 17 psi).


NEXT


12.READ VALUE OF INTELLIGENT TESTER
  1. Using the intelligent tester, check ID1 data of the tire pressure.


NEXT


13.CONFIRM VALUE OF ID1 TIRE PRESSURE
  1. Check the value of the ID1 tire pressure was set to 120 kPa (1.2 kgf*cm2, 17 psi).

    Result:
    Result
    Proceed to
    The rear left wheel is set to value above.
    A
    Except left right wheel is set to value above.
    B



A
ID1 IS FOR REAR LEFT WHEEL TRANSMITTER
B

ID1 IS FOR SPARE TIRE TRANSMITTER