Home › SUSPENSION & AXLE › TIRE AND WHEEL › TIRE PRESSURE WARNING SYSTEM

DTC    C2121/21    No Signal from Transmitter ID1

DTC    C2122/22    No Signal from Transmitter ID2

DTC    C2123/23    No Signal from Transmitter ID3

DTC    C2124/24    No Signal from Transmitter ID4

DTC    C2125/25    No Signal from Transmitter ID5

DTC    C2181/81    Transmitter ID1 not Received (Test Mode DTC)

DTC    C2182/82    Transmitter ID2 not Received (Test Mode DTC)

DTC    C2183/83    Transmitter ID3 not Received (Test Mode DTC)

DTC    C2184/84    Transmitter ID4 not Received (Test Mode DTC)

DTC    C2185/85    Transmitter ID5 not Received (Test Mode DTC)

for Preparation Click here


DESCRIPTION

The tire pressure monitor valve sub-assembly constantly sends radio waves to the tire pressure monitor receiver assembly. If the battery for the tire pressure monitor valve sub-assembly is depleted, or if the tire pressure monitor receiver assembly is defective or comes off, the DTC will be output. DTCs C2121/21 to C2125/25 can only be deleted by the tester. DTCs C2181/81 to C2185/85 can be deleted when the transmitter sends a force transmission signal or the test mode ends. DTCs C2181/81 to C2185/85 are output only in the test mode.

DTC No.
DTC Detecting Condition
Trouble Area
C2121/21
C2122/22
C2123/23
C2124/24
C2125/25
C2181/81
C2182/82
C2183/83
C2184/84
C2185/85
A DTC is detected when the ECU receives no signals for 51 minutes or more, the vehicle speed is 8 km/h or higher, and the ECU receives no signals for 12 minutes or more.
  1. Tire pressure monitor receiver assembly
  2. Each tire pressure monitor valve sub-assembly
  3. Tire pressure monitor ECU

HINT:
It is necessary to perform the procedure to identify the tire pressure monitor valve sub-assembly that is malfunctioning because it cannot be identified by the output DTC.


WIRING DIAGRAM


F045859E01


INSPECTION PROCEDURE

HINT:
Set the tire pressure to the specified value.

1.CHECK TIRE PRESSURE WARNING LIGHT
  1. Turn the ignition switch to the ON position.

  1. Check the tire pressure warning light.

    Result:

    Proceed to
    Result
    A
    Does not blink
    B
    Comes on and goes off repeatedly at 0.5 second intervals



B
Go to step 4
A


2.CLEAR DTC

NEXT


3.CHECK DTC
  1. Check for DTC.

    OK:
    DTC is not output.



NG
Go to step 4
OK

GO TO PROBLEM SYMPTOMS TABLE 

4.CHECK DTC
  1. Check if DTCs C2121/21, C2122/22, C2123/23, C2124/24 and C2125/25 are all output.



NO
Go to step 7
YES


5.CHECK HARNESS AND CONNECTOR (TIRE PRESSURE WARNING RECEIVER - TIRE PRESSURE MONITOR ECU)


    F045860E01
  1. Disconnect the tire pressure monitor receiver assembly T17 connector and tire pressure monitor ECU T16 connector.



    F045861E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Specified Condition
    T16-7 (RDA) - T17-1 (RDA)
    Below 1 Ω
    T16-8 (RF5V) - T17-5 (+5V)
    Below 1 Ω
    T16-16 (GND2) - T17-4 (GND)
    Below 1 Ω
    T16-7 (RDA) - Body ground
    10 kΩ or higher
    T16-8 (RF5V) - Body ground
    10 kΩ or higher
    T16-16 (GND2) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK TIRE PRESSURE WARNING RECEIVER


    F045868E02
  1. Connect the tire pressure monitor ECU T16 connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Specified Condition
    T16-8 (RF5V) - T16-16 (GND2)
    4.5 to 5.5 V



NG
GO TO POWER SOURCE CIRCUIT
OK

REPLACE TIRE PRESSURE WARNING RECEIVER 

7.SET TIRE PRESSURE TO NORMAL VALUE
  1. Set the tire pressure of all wheels to the specified value.

    Front
    Rear
    Spare
    220 kPa (2.2 kgf/cm2, 32 psi)
    220 kPa (2.2 kgf/cm2, 32 psi)
    220 kPa (2.2 kgf/cm2, 32 psi)


NEXT


8.IDENTIFY TRANSMITTER CORRESPONDING TO DTC

HINT:
Refer to "Error in Present while Identifying Transmitter" (Click here).


NEXT


9.INTERCHANGE TIRES

HINT:
When "A" (left front) is identified at step 8.



    F046785E01
  1. Interchange tire "A" for the identified tire pressure monitor valve sub-assembly with tire "B" for a normal one.


NEXT


10.SET TIRE PRESSURE TO NORMAL VALUE
  1. Set the tire pressure of all wheels to the specified value.

    Front
    Rear
    Spare
    220 kPa (2.2 kgf/cm2, 32 psi)
    220 kPa (2.2 kgf/cm2, 32 psi)
    220 kPa (2.2 kgf/cm2, 32 psi)


NEXT


11.FORCIBLY TRANSMIT TRANSMITTER ID


    F046786E01
  1. Remove the valve core of the tire "A", rapidly reduce the tire pressure and forcibly transmit the transmitter ID of the tire pressure monitor valve sub-assembly.


NEXT


12.CHECK DTC
  1. Check for DTC.

    OK:
    DTC is not output

    HINT:
    1. If a DTC is output, replace the identified tire pressure monitor valve sub-assembly.
    2. Register the transmitter ID after replacing and then set the tire pressure to the specified value.



NG
REPLACE TIRE PRESSURE WARNING VALVE AND TRANSMITTER
OK

REPLACE TIRE PRESSURE WARNING RECEIVER