Home › BODY › INSTRUMENT PANEL › INSTRUMENT PANEL SAFETY PAD

INSTRUMENT PANEL SAFETY PAD > REMOVAL

for Preparation Click here



1. BOLT, SCREW AND NUT TABLE


HINT:
The bolts, screws and nuts, which are necessary for installation and removal of the instrument panel are shown in the illustration below and the text with alphabets.



B065712E01



2. DISCONNECT BATTERY NEGATIVE TERMINAL

HINT:
Click here



3. REMOVE INSTRUMENT PANEL FINISH PLATE


    B062737
  1. Remove the instrument panel finish plate.



4. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY


    B062738E01
  1. Remove the 2 bolts <B>.

  1. Disconnect the hood lock control cable assembly and fuel lid lock control cable sub-assembly.

  1. Disengage the 4 clips.

  1. Disconnect the connectors and remove the lower instrument panel finish panel sub-assembly.



5. REMOVE CONSOLE UPPER REAR PANEL SUB-ASSEMBLY


    B062740E01
  1. Disengage the 5 clips and 2 claws, and remove the console upper rear panel, and then disconnect the connectors.



6. REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY


    B062741E01
  1. Disengage the 6 clips and 2 claws, and then remove the upper console panel sub-assembly.

    NOTICE:
    Be careful not to snap the claws during the operation.



7. REMOVE NO. 1 CONSOLE UPPER PANEL GARNISH


    B062742E01
  1. Disengage the clip.

  1. Pull the No. 1 console upper panel garnish rearward to be removed.



8. REMOVE NO. 2 CONSOLE UPPER PANEL GARNISH


9. REMOVE AIR CONDITIONING CONTROL ASSEMBLY


    B062744
  1. Remove the screw.



    B062757E01
  1. Disengage the 4 clips and remove the air conditioner, and then disconnect the connectors.



10. REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY


    B062745E01
  1. Remove the 3 bolts <C>.

  1. Disengage the 8 clips and remove the center instrument cluster finish panel sub-assembly.



11. REMOVE RADIO RECEIVER ASSEMBLY (w/ Bracket)


    E115642
  1. Remove the 2 bolts.

  1. Disconnect the connectors and remove the radio receiver assembly with bracket.



12. REMOVE NO. 2 LOWER STEERING WHEEL COVER


13. REMOVE NO. 3 LOWER STEERING WHEEL COVER


14. REMOVE STEERING PAD


    F043322
  1. Using a "torx" socket wrench (T30), loosen the 2 "torx" screws until the groove along the screw circumference catches on the screw case.



    H042354
  1. Pull out the steering pad from the steering wheel assembly and support the steering pad with one hand as shown in the illustration.

    NOTICE:
    When removing the steering pad, do not pull the airbag wire harness.

  1. Using a screw driver, disconnect the 2 connectors from the steering pad.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.

  1. Remove the steering pad.



15. REMOVE STEERING WHEEL ASSEMBLY


    F043320E01
  1. without Steering pad switch:
    Disconnect the connector.

  1. Remove the steering wheel assembly set nut.

  1. Mark matchmarks on the steering wheel assembly and main shaft assembly.

  1. Set the SST on the steering wheel assembly.

  1. Holding the SST to the monkey spanner and turn the SST, then remove the steering wheel assembly.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05021)



16. REMOVE UPR STEERING COLUMN COVER


17. REMOVE TURN SIGNAL SWITCH ASSEMBLY (w/ Bracket)


    F043318
  1. Disconnect the 3 connectors.

  1. Remove the 3 screws and turn signal switch assembly.



18. REMOVE INSTRUMENT PANEL LOWER LH


    B062739E01
  1. Remove the 2 bolts <B>.

  1. Disengage the 2 claws and remove the instrument panel lower LH.



19. REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY


    B062746E01
  1. Disengage the 7 clips.

  1. Disconnect the connectors and remove the instrument cluster finish panel sub-assembly.



20. REMOVE COMBINATION METER ASSEMBLY


    B062747
  1. Remove the 3 screws.

  1. Loosen the 2 bolts and remove the combination meter assembly.



21. REMOVE REAR CONSOLE BOX ASSEMBLY


    B078371E01
  1. Disconnect the connectors.

  1. Remove the 6 bolts <B> and rear console box assembly.



22. REMOVE FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedure described for the LH side.



23. REMOVE COWL SIDE TRIM BOARD RH


    B062748E01
  1. Remove the clip.

  1. Disengage the 2 claws and remove the cowl side trim board RH.



24. REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY


    B062749E01
  1. Remove the screw <E>.

  1. Disengage the 3 clips and remove the No. 2 instrument panel under cover sub-assembly.



25. REMOVE GLOVE COMPARTMENT DOOR SUB-ASSEMBLY


    B062750E01
  1. Remove the screw <F> and glove compartment door.

  1. Deform the upper part of the glove compartment door to release the stoppers.

  1. Pull the glove compartment door upward to remove it.



26. DISCONNECT PASSENGER AIRBAG CONNECTOR


    H042181
  1. Disconnect the connector from the passenger airbag assembly connector.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.



27. REMOVE NO. 2 LOWER INSTRUMENT PANEL FINISH PANEL


    B062751E01
  1. Remove the 4 screws <E>.

  1. Disengage the 2 claws and remove the instrument panel finish panel.



28. REMOVE NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY


    B062752E01
  1. Remove the screw <G>.

  1. Disengage the 2 clips and 2 claws, and then remove the No. 2 instrument panel register assembly.



29. REMOVE ASSIST GRIP SUB-ASSEMBLY


30. REMOVE FRONT PILLAR GARNISH LH


    B063600E04
  1. Using a screwdriver, remove the 2 assist grip plugs.

    HINT:
    Tape the screwdriver tip before use.

  1. Remove the 2 bolts.

  1. Using a screwdriver, disengage the claw. Remove the clip labeled A, clip labeled B and pillar garnish.



31. REMOVE FRONT PILLAR GARNISH RH

HINT:
Use the same procedure described for the LH side.



32. REMOVE INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY


  1. Remove the 9 bolts <A> <B> <C> and nut <H>.


    B120219E01

  1. Disconnect the connectors.

  1. Remove the instrument panel safety pad sub-assembly.



33. REMOVE NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY
  1. Using a moulding remover, disengage the 4 clips and remove the No. 1 instrument panel speaker panel sub-assembly.



34. REMOVE FRONT STEREO COMPONENT SPEAKER ASSEMBLY
  1. Remove the 2 screws <D> and the front stereo component speaker assembly.



35. REMOVE NO. 1 INSTRUMENT PANEL PIN
  1. Remove the screw <D> and the No. 1 instrument panel pin.



36. REMOVE DEFROSTER NOZZLE ASSEMBLY
  1. Remove the 2 screws <D> and the defroster nozzle assembly.



37. REMOVE NO. 2 HEATER TO REGISTER DUCT
  1. Remove the 5 screws <D> and the No. 2 heater to register duct.



38. REMOVE NO. 1 METER HOOD RETAINER
  1. Remove the screw <D> and the No. 1 meter hood retainer.



39. REMOVE CENTER INSTRUMENT PANEL BRACKET SUB-ASSEMBLY
  1. Remove the screw <D> and the center instrument panel bracket sub-assembly.



40. REMOVE AUTOMATIC LIGHT CONTROL SENSOR
  1. Disconnect the connector.

  1. Remove the automatic light control sensor.



41. REMOVE COOLER (SOLAR SENSOR) THERMISTOR
  1. Disconnect the connector.

  1. Remove the cooler (solar sensor) thermistor.



42. REMOVE NO. 2 INSTRUMENT PANEL WIRE


43. REMOVE ANTENNA CORD SUB-ASSEMBLY


  1. Remove the 4 clamps and antenna cord sub-assembly.


    I033314E01



44. REMOVE NAVIGATION ANTENNA ASSEMBLY (w/ Navigation System)


    I033320
  1. Remove the 3 clamps.

  1. Remove the 2 screws and navigation antenna.



45. REMOVE INSTRUMENT CLUSTER FINISH PANEL GARNISH
  1. Remove the 3 screws <D> and the instrument cluster finish panel garnish.



46. REMOVE FRONT PASSENGER AIRBAG ASSEMBLY


    C131377
  1. Disengage the 3 clamps.



    C131378
  1. Remove the 3 screws and the front passenger airbag assembly.



    C131326E01
  1. Release the rear side wall of the airbag door from the hook by slightly deflecting it and roll the front passenger airbag assembly forward.

  1. Release the front side wall of the airbag door from the other hook and remove the front passenger airbag assembly.



47. REMOVE INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY