Home › BODY ELECTRICAL › DOOR LOCK › POWER DOOR LOCK CONTROL SYSTEM

POWER DOOR LOCK CONTROL SYSTEM > All Doors LOCK / UNLOCK Functions do not Operate Via Master Switch, Driver Side Door Key Cylinder

for Preparation Click here


DESCRIPTION

The body ECU receives a switch signal from the master switch and the driver side door key cylinder, and then drives the door lock motor.

WIRING DIAGRAM


B134220E01


B134221E01


INSPECTION PROCEDURE

1.PERFORM ACTIVE TEST BY INTELLIGENT TESTER
  1. Select the active test, and then check that the power door lock operates.

    HINT:
    During the active test, the intelligent tester sends signal to the body ECU to drive all the power door lock motor. If the all power door lock operates, the power door lock motor itself and the wire harness between the power door lock motor and body ECU are considered normal.


    BODY: 
    Item
    Test Details
    Diagnostic Note
    DOOR LOCK
    Drive door lock motor at all doors LOCK/OFF
    -
    DOOR LOCK
    Drive door lock motor at all doors UNLOCK/OFF
    -



NG
REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
OK


2.CHECK MASTER SWITCH OR KEY CYLINDER
  1. Check master switch or key cylinder operation.

    1. When manual door lock/unlock operation via the master switch can not be performed, proceed to A.

    2. When manual door lock/unlock operation via the door lock control switch (passenger side) can not be performed, proceed to B.

    3. When manual door lock/unlock operation interlocked with the driver side door lock key cylinder can not be performed, proceed to C.



B
Go to step 4

C
Go to step 5
A


3.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY


    B059539E21
  1. Remove the master switch.

  1. Inspect the door lock control switch continuity.

    Standard resistance:
    Terminal No.
    Door Lock Position
    Specified Condition
    1 - 5
    Lock
    Below 1 Ω
    -
    OFF
    10 kΩ or higher
    1 - 8
    Unlock
    Below 1 Ω



OK
REPAIR OR REPLACE HARNESS OR CONNECTOR
NG

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY 

4.INSPECT DOOR CONTROL SWITCH ASSEMBLY


    B134223E01
  1. Passenger side switch:
    Inspect the door lock control switch continuity.

    Standard resistance:
    Terminal No.
    Door Lock Position
    Specified Condition
    3 - 6
    Lock
    Below 1 Ω
    -
    OFF
    10 kΩ or higher
    3 - 5
    Unlock
    Below 1 Ω



OK
REPAIR OR REPLACE HARNESS OR CONNECTOR
NG

REPLACE DOOR CONTROL SWITCH ASSEMBLY 

5.INSPECT FRONT DOOR W/MOTOR LOCK ASSEMBLY LH


    B056798E02
  1. Apply battery voltage and inspect operation of the door lock motor.

    Standard:
    Measurement Condition
    Specified Condition
    Battery positive (+) → Terminal 4
    Battery negative (-) → Terminal 1
    Lock
    Battery positive (+) → Terminal 1
    Battery negative (-) → Terminal 4
    Unlock



    B056797E02
  1. Inspect the door lock and unlock switch continuity.

    Standard resistance:
    Terminal No.
    Door Lock Position
    Specified Condition
    7 - 9
    Lock
    Below 1 Ω
    -
    OFF
    -
    7 - 10
    Unlock
    Below 1 Ω

  1. Inspect the position switch continuity.

    Standard resistance:
    Terminal No.
    Door Lock Position
    Specified Condition
    7 - 8
    Lock
    10 kΩ or higher
    Unlock
    Below 1 Ω



OK
REPAIR OR REPLACE HARNESS OR CONNECTOR
NG

REPLACE FRONT DOOR W/MOTOR LOCK ASSEMBLY LH