Home › ENGINE ยท 1GR-FE › COOLING › WATER PUMP

WATER PUMP > INSTALLATION

for Preparation Click here



1. INSTALL WATER PUMP ASSEMBLY
  1. Install a new gasket and the water pump with the 17 bolts.

    Torque:
    10 mm (0.39 in.) head:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }
    12 mm (0.47 in.) head:
    23 N*m{ 235 kgf*cm , 17 ft.*lbf }



2. INSTALL V-RIBBED BELT TENSIONER ASSEMBLY


    A076445E02
  1. Temporarily install the V-ribbed belt tensioner with the 5 bolts.

  1. Install the V-ribbed belt tensioner by tightening the bolt 1 and bolt 2 in the order shown in the illustration.

    Torque:
    36 N*m{ 367 kgf*cm , 27 ft.*lbf }

  1. Tighten the other bolts.

    Torque:
    36 N*m{ 367 kgf*cm , 27 ft.*lbf }

    HINT:
    Each bolt length is as follows:
    A: 70 mm (2.76 in.)
    B: 33 mm (1.30 in.)



3. INSTALL COOLER COMPRESSOR ASSEMBLY
  1. Install the cooler compressor assembly with the 4 bolts.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }

  1. Connect the cooler compressor assembly connector.



    A076416
  1. Install the suction hose sub-assembly with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



4. INSTALL GENERATOR ASSEMBLY
  1. Install the generator assembly with the 2 bolts.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }

  1. Install the wire harness clamp bracket with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Connect the wire harness.

    1. Connect the wire harness to the terminal B and install the nut.

      Torque:
      9.8 N*m{ 100 kgf*cm , 7 ft.*lbf }

    2. Connect the connector to the generator assembly.

    3. Install the wire harness stay with the bolt.

      Torque:
      8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



5. INSTALL NO. 2 IDLER PULLEY SUB-ASSEMBLY
  1. Install the 2 idler pulleys with the 2 bolts.

    Torque:
    39 N*m{ 398 kgf*cm , 29 ft.*lbf }



6. INSTALL WATER INLET


    A076340
  1. Install a new O-ring to the water outlet pipe.

  1. Install a new gasket to the water pump.

  1. Apply soapy water to the O-ring.



    A076337
  1. Install the water inlet with the 5 bolts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

  1. Connect the 5 water by-pass hoses.

  1. Connect the 2 radiator hoses.

  1. Connect the 2 oil cooler hoses (with oil cooler).



7. INSTALL AIR CLEANER ASSEMBLY


8. CONNECT VENTILATION HOSE NO.2


9. INSTALL FAN WITH FLUID COUPLING
  1. Put the fan pulley to the water pump.

  1. Put the fan with fluid coupling and fan shroud together.

  1. Temporarily install the 4 fluid coupling nuts.

  1. Tighten the 2 fan shroud bolts and radiator reserve tank bolt.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Connect the reserve tank hose.

  1. Fasten the 2 oil cooler hoses with the hose clamp.



10. INSTALL FAN AND GENERATOR V BELT


    A076442E02
  1. While turning the belt tensioner counterclockwise, align with its holes, and then insert a bar of 6 mm (0.24 in.) into the holes to fix the belt tensioner.

  1. Install the V-ribbed belt.

  1. While turning the belt tensioner counterclockwise, remove the bar.



    A076443E02
  1. If it is hard to install the V-ribbed belt, perform the following procedure.

    1. Put the V-ribbed belt on all parts except the P/S pump, as shown in the illustration.

    2. While releasing the belt tension by turning the belt tensioner counterclockwise, put the V-ribbed belt on the P/S pump.



11. FULLY TIGHTEN FAN WITH FLUID COUPLING
  1. Tighten the 4 fluid coupling bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



12. INSTALL RADIATOR SUPPORT SEAL UPPER


13. ADD ENGINE COOLANT
  1. Slowly fill the system with engine coolant.

    Capacity:
    9.8 liters (10.4 Us qts, 8.6 Imp. qts)

    HINT:
    1. Use of improper coolants may damage the engine cooling system.
    2. Use only Toyota Super Long Life Coolant or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, and non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).
    3. New Toyota vehicles are filled with Toyota Super Long Life Coolant (color is pink, premixed ethylene glycol concentration is approximately 50 % and freezing temperature is -35°C (-31°F)). When replacing the coolant, Toyota Super Long Life Coolant is recommended.
    4. Observe the coolant level inside the radiator by pressing the inlet and outlet radiator hoses several times by hand. If the coolant level goes down, add the coolant.

    NOTICE:
    Do not substitute plain water for engine coolant.

  1. Install the radiator cap securely.

  1. Bleed the cooling system.

    1. Open the heater water valve while warming up the engine.

    2. Maintain the engine speed at 2,000 to 2,500 rpm and warm up the engine.

  1. Stop the engine and wait until the coolant cools down.

  1. Add coolant into the reservoir until the coolant level is FULL.



14. INSPECT ENGINE COOLANT LEAKAGE
  1. Fill the radiator with coolant and attach a radiator cap tester.

  1. Pump it to 118 kPa (1.2 kgf/cm2 17.1 psi), then check for leakage.



15. INSTALL V-BANK COVER
  1. Install the V-bank cover with the 2 nuts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }



16. REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY
  1. Install the engine under cover with the 4 bolts.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }