ENGINE UNIT > INSPECTION |
| 1. INSPECT CAMSHAFTS |
![]() |
Inspect the camshaft for runout.
Place the camshaft on V-blocks.
Using a dial indicator, measure the runout at the center journal.
![]() |
Inspect the cam lobes.
Using a micrometer, measure the cam lobe height.
![]() |
Inspect the camshaft journals.
Using a micrometer, measure the journal diameter.
| 2. INSPECT CAMSHAFT TIMING GEAR ASSEMBLY |
Fix the intake camshaft with a vise.
![]() |
Align the knock pin hole in the camshaft timing gear assembly with the knock pin of the camshaft, and install the camshaft timing gear assembly with the bolt.
Confirm the camshaft timing gear assembly is locked.
![]() |
Release the lock pin.
Cover 4 oil paths of the cam journal with a masking tape as shown in the illustration.
Prick a hole in the tape placed on the advance side path. Prick a hole in the retard side path, on the opposite side to that of the advance side path, as shown in the illustration.
![]() |
Apply about 200 kPa (2.0 kgf/cm2) of air pressure to the two broken paths (the advance side path and the retard side path).
![]() |
Confirm that the camshaft timing gear assembly rotates in the advance direction when reducing the air pressure applied to the retard path.
When the camshaft timing gear comes to the most advanced position, release the air pressure from the retard side path, and then release the air pressure from the advance side path.
Check for smooth revolution.
Except the position where the lock pin meets at the most retard angle, turn the camshaft timing gear assembly back and forth and check the movable range and that there is no disturbance.
Check the lock in the most retarded position.
Confirm that the camshaft timing gear assembly is locked at the most retarded position.
![]() |
Remove the set bolt and camshaft timing gear assembly.
| 3. INSPECT CYLINDER HEAD SET BOLT |
![]() |
Using vernier calipers, measure the outside thread diameter of the bolt.
| 4. INSPECT CHAIN SUB-ASSEMBLY |
![]() |
Using a spring scale, pull the chain sub assembly with a force of 147 N (15.0 kgf, 33.1 lbf) and measure the length of the chain sub assembly by vernier calipers.
| 5. INSPECT NO. 2 CHAIN SUB-ASSEMBLY |
![]() |
Using a spring scale, pull the chain sub assembly with a force of 147 N (15.0 kgf, 33.1 lbf) and measure the length of the chain sub assembly by vernier calipers.
| 6. INSPECT CAMSHAFT TIMING GEAR ASSEMBLY |
![]() |
Put the No. 1 chain on the larger gear of the camshaft timing gear assembly.
Using vernier calipers, measure the timing gear with the chain.
![]() |
Put the No. 2 chain on the smaller gear of the camshaft timing gear assembly.
Using vernier calipers, measure the timing gear with the chain.
| 7. INSPECT CAMSHAFT TIMING GEAR OR SPROCKET |
![]() |
Put the No. 2 chain on the camshaft timing gear.
Using vernier calipers, measure the camshaft timing gear diameter with the chain .
| 8. INSPECT CRANKSHAFT TIMING GEAR OR SPROCKET |
![]() |
Put the No. 1 chain on the crankshaft timing gear.
Using vernier calipers, measure the crankshaft timing gear diameter with the chain.
| 9. INSPECT NO. 1 IDLE GEAR |
![]() |
Put the No. 1 chain on the idle gear.
Using vernier calipers, measure the idle gear with the chain.
| 10. INSPECT IDLE GEAR SHAFT OIL CLEARANCE |
![]() |
Using a micrometer, measure the idle gear shaft diameter.
![]() |
Using a caliper gauge, measure the inside diameter of the idle gear.
Subtract the idle gear shaft diameter measurement from the idle gear inside diameter measurement.
| 11. INSPECT NO. 1 CHAIN TENSIONER ASSEMBLY |
![]() |
Check that the plunger moves smoothly when the ratchet pawl is raised with your finger.
Release the ratchet pawl and check that the plunger is locked in place by the ratchet pawl and does not move when pushing with your finger.
| 12. INSPECT NO. 2 CHAIN TENSIONER ASSEMBLY |
![]() |
Check that the plunger moves smoothly.
Measure the worn depth of the chain tensioner slipper.
| 13. INSPECT NO. 3 CHAIN TENSIONER ASSEMBLY |
![]() |
Check that the plunger moves smoothly.
Measure the worn depth of the chain tensioner slipper.
| 14. INSPECT CHAIN TENSIONER SLIPPER |
![]() |
Measure the worn depth of the chain tensioner slipper.
| 15. INSPECT NO. 1 CHAIN VIBRATION DAMPER |
![]() |
Measure the worn depth of the No. 1 chain vibration damper.
| 16. INSPECT NO. 2 CHAIN VIBRATION DAMPER |
![]() |
Measure the worn depth of the No. 2 chain vibration damper.
| 17. CLEAN CYLINDER HEAD SUB-ASSEMBLY |
![]() |
Using a gasket scraper, remove all the gasket material from the cylinder block contact surface.
![]() |
Using a wire brush, remove all the carbon from the combustion chambers.
![]() |
Using a valve guide bushing brush and solvent, clean all the valve guide bushes.
![]() |
Using a soft brush and solvent, thoroughly clean the cylinder head.
| 18. INSPECT CYLINDER HEAD SUB-ASSEMBLY |
![]() |
Inspect warpage.
Using a precision straight edge and feeler gauge, measure the warpage of the contact surfaces of the cylinder block and manifolds.
![]() |
Inspect cranks.
Using a dye penetrant, check the combustion chamber, intake ports, exhaust ports and cylinder block surface for cracks.
If cracked, replace the cylinder head.
| 19. CLEAN VALVE |
![]() |
Using a gasket scraper, chip off any carbon from the valve head.
Using a wire brush, thoroughly clean the valve.
| 20. INSPECT VALVE |
![]() |
Inspect the valve stem diameter.
Using a micrometer, measure the diameter of the valve stem.
| Intake | Exhaust |
| 5.470 to 5.485 mm (0.2154 to 0.2159 in.) | 5.465 to 5.480 mm (0.2152 to 0.2158 in.) |
![]() |
Inspect the valve face angle.
Grind the valve enough to remove pits and carbon.
Check that the valve is ground to the correct valve face angle.
![]() |
Inspect the valve head margin thickness.
Using vernier calipers, check the valve head margin thickness.
![]() |
Inspect the overall length.
Using vernier calipers, check the overall length.
| Intake | Exhaust |
| 106.95 mm (4.2106 in.) | 105.80 mm (4.1654 in.) |
| Intake | Exhaust |
| 106.40 mm (4.1890 in.) | 105.30 mm (4.1457 in.) |
![]() |
Inspect the valve stem tip.
Check the surface of the valve stem tip for wear.
| 21. CLEAN VALVE SEAT |
![]() |
Using a 45° carbide cutter, resurface the valve seats.
Clean the valve seats.
| 22. INSPECT VALVE SEAT |
![]() |
Apply a light coat of prussian blue (or white lead) to the valve face.
Lightly press the valve against the valve seat.
Check the valve face and seat according to the following procedure.
If prussian blue appears around the entire face, the valve is centered.
If not, replace the valve.
If prussian blue appears around the entire valve seat, the guide and face are centered.
If not, resurface the valve seat.
Check that the seat contacts the middle of the valve face with the width below.
| 23. REPAIR VALVE SEAT |
![]() |
If the seating is too high to the valve face, use 30° and 45° cutters to correct the seat.
![]() |
Intake side:
If the seating is too low to the valve face, use 60° and 45° cutters to correct the seat.
![]() |
Exhaust side:
If the seating is too low to the valve face, use 75° and 45° cutters to correct the seat.
![]() |
Handrub the valve and valve seat with an abrasive compound.
After handrubbing, clean the valve and valve seat.
| 24. INSPECT INNER COMPRESSION SPRING |
![]() |
Inspect squareness.
Using a steel square, measure the squareness of the inner compression spring.
![]() |
Inspect free length.
Using vernier calipers, measure the free length of the inner compression spring.
![]() |
Inspect tension.
Using a spring tester, measure the tension of the inner compression spring at the specified installed length.
| 25. INSPECT VALVE GUIDE BUSH OIL CLEARANCE |
![]() |
Using a caliper gauge, measure the inside diameter of the valve guide bush.
Subtract the valve stem diameter measurement (Step 8) from the valve guide bush inside diameter measurement.
| Intake | Exhaust |
| 0.025 to 0.060 mm (0.0010 to 0.0024 in.) | 0.030 to 0.065 mm (0.0012 to 0.0026 in.) |
| Intake | Exhaust |
| 0.08 mm (0.0031 in.) | 0.10 mm (0.0039 in.) |
| 26. REMOVE VALVE GUIDE BUSH |
![]() |
Gradually heat the cylinder head to 80 to 100°C (176 to 212°F).
![]() |
Place the cylinder head on a wooden block.
Using SST, tap out the valve guide bush.
| 27. INSTALL VALVE GUIDE BUSH |
![]() |
Using a caliper gauge, measure the bush bore diameter of the cylinder head.
| STD | 10.333 to 10.344 mm (0.4068 to 0.4072 in.) |
| O/S 0.05 | 10.383 to 10.394 mm (0.4088 to 0.4092 in.) |
![]() |
Gradually heat the cylinder head to 80 to 100°C (176 to 212°F).
![]() |
Place the cylinder head on a wooden block.
Using SST, tap in a new valve guide bush to the specified protrusion height.
![]() |
Using a sharp 5.5 mm reamer, ream the valve guide bush to obtain the standard specified clearance between the valve guide bush and valve stem.
| Intake | Exhaust |
| 0.025 to 0.060 mm (0.0010 to 0.0024 in.) | 0.030 to 0.065 mm (0.0012 to 0.0026 in.) |
| 28. INSPECT VALVE LIFTER |
![]() |
Using a micrometer, measure the valve lifter diameter.
| 29. INSPECT VALVE LIFTER OIL CLEARANCE |
![]() |
Using a caliper gauge, measure the lifter bore diameter of the cylinder head.
Subtract the valve lifter diameter measurement (Step 16) from the lifter bore diameter measurement.
| 30. INSPECT CAMSHAFT OIL CLEARANCE |
![]() |
Clean the camshaft bearing caps, camshaft bearings and camshaft journals.
Install the camshaft bearing .
Place the camshaft on the cylinder head.
Lay a strip of Plastigage across each of the camshaft journals.
Install the camshaft bearing caps .
Remove the camshaft bearing caps .
![]() |
Measure the Plastigage at its widest point.
| No. 1 (Intake) | No. 1 (Exhaust) | Others |
| 0.008 to 0.038 mm (0.0003 to 0.0015 in.) | 0.040 to 0.079 mm (0.0016 to 0.0031 in.) | 0.025 to 0.062 mm (0.0010 to 0.0024 in.) |
| No. 1 | Others |
| 0.040 to 0.079 mm (0.0016 to 0.0031 in.) | 0.025 to 0.062 mm (0.0010 to 0.0024 in.) |
| No. 1 (Intake) | Others |
| 0.07 mm (0.0028 in.) | 0.10 mm (0.0039 in.) |
| Cylinder head journal bore diameter | 40.009 to 40.017 mm (1.5752 to 1.5755 in.) |
| Camshaft bearing center wall thickness (Mark "2") | 2.004 to 2.008 mm (0.0789 to 0.0791 in.) |
| Camshaft journal diameter | 35.971 to 35.985 mm (1.4165 to 1.4167 in.) |
Remove the Plastigage completely.
Remove the camshafts.
Remove the camshaft bearing.
| 31. INSPECT CAMSHAFT THRUST CLEARANCE |
![]() |
Install the camshafts .
Using a dial indicator, measure the thrust clearance while moving the camshaft back and forth.
| 32. INSPECT CYLINDER BLOCK FOR FLATNESS |
![]() |
Using a precision straight edge and feeler gauge, measure the warpage of the contact surface of the cylinder head gasket.
| 33. INSPECT CYLINDER BORE |
![]() |
Using a cylinder gauge, measure the cylinder bore diameter at positions A and B in the thrust and axial directions.
| 34. INSPECT WITH PIN PISTON SUB-ASSEMBLY |
![]() |
Using a micrometer, measure the piston diameter at right angles to the piston pin center line, 27.7 mm (1.091 in.) from the piston head.
| 35. INSPECT PISTON OIL CLEARANCE |
Subtract the piston diameter measurement from the cylinder bore diameter measurement.
| 36. INSPECT CONNECTING ROD SUB-ASSEMBLY |
![]() |
Using a rod aligner and feeler gauge, check the connecting rod alignment.
Check for misalignment.
![]() |
Check twist.
| 37. INSPECT PISTON PIN OIL CLEARANCE |
![]() |
Using a caliper gauge, measure the inside diameter of the piston pin hole.
| Mark | mm (in.) |
| A | 22.001 to 22.004 (0.8662 to 0.8663) |
| B | 22.005 to 22.007 (0.8663 to 0.8664) |
| C | 22.008 to 22.010 (0.8665 to 0.8665) |
![]() |
Using a micrometer, measure the piston pin diameter.
| Mark | mm (in.) |
| A | 21.997 to 22.000 (0.8660 to 0.8661) |
| B | 22.001 to 22.003 (0.8661 to 0.8663) |
| C | 22.004 to 22.006 (0.8663 to 0.8664) |
![]() |
Using a caliper gauge, measure the inside diameter of the connecting rod bushing.
| Mark | mm (in.) |
| A | 22.005 to 22.008 (0.8663 to 0.8665) |
| B | 22.009 to 22.011 (0.8665 to 0.8666) |
| C | 22.012 to 22.014 (0.8666 to 0.8667) |
Subtract the piston pin diameter measurement from the piston pin hole diameter measurement.
![]() |
If the oil clearance is greater than the maximum, replace the bushing. If necessary, replace the piston and piston pin together.
Subtract the piston pin diameter measurement from the bushing inside diameter measurement.
If the oil clearance is greater than the maximum, replace the bushing. If necessary, replace the connecting rod and piston pin together.
| 38. REMOVE CONNECTING ROD SMALL END BUSH |
![]() |
Using SST and a press, press out the bushing.
| 39. INSTALL CONNECTING ROD SMALL END BUSH |
![]() |
Align the oil holes of a new bushing and the connecting rod.
![]() |
Using SST and a press, press in the bushing.
![]() |
Using a pin hole grinder, hone the bushing to obtain the standard specified clearance between the bushing and piston pin.
| 40. INSPECT RING GROOVE CLEARANCE |
![]() |
Using a feeler gauge, measure the clearance between the new piston ring and the wall of the ring groove.
| 41. INSPECT PISTON RING END GAP |
![]() |
Using a piston, push the piston ring a little beyond the bottom of the ring travel, 110mm (4.33 in.) from the top of the cylinder block.
![]() |
Using a feeler gauge, measure the end gap.
| 42. INSPECT CONNECTING ROD BOLT |
![]() |
Using vernier calipers, measure the tension portion diameter of the bolt.
| 43. INSPECT CRANKSHAFT BEARING CAP SET BOLT |
![]() |
Using vernier calipers, measure the tension portion diameter of the bolt.
| 44. INSPECT CRANKSHAFT |
![]() |
Using a dial indicator and V-blocks, measure the runout as shown in the illustration.
![]() |
Using a micrometer, measure the diameter of each main journal.
Check each main journal for taper and out-of-round as shown.
![]() |
Using a micrometer, measure the diameter of each crank pin.
Check each crank pin for taper and out-of-round as shown.
| 45. INSPECT CRANKSHAFT OIL CLEARANCE |
![]() |
Clean each main journal and bearing.
![]() |
Align the bearing claw with the claw groove of the cylinder block, and push in the 4 upper bearings.
![]() |
Align the bearing claw with the claw groove of the main bearing cap, and push in the 4 bottom bearings.
Place the crankshaft on the cylinder block.
![]() |
Lay a strip of Plastigage across each journal.
![]() |
Examine the front marks and numbers and install the bearing caps on the cylinder block.
Apply a light coat of engine oil to the threads of the bearing cap bolts.
Temporarily install the 8 main bearing cap bolts to the inside positions.
![]() |
Install the main bearing caps. Tighten the 2 bolts for each bearing cap until the clearance between the bearing cap and the cylinder block becomes less than 6 mm (0.23 in.).
![]() |
Using a plastic-faced hammer, lightly tap the bearing cap to ensure a proper fit.
Apply a light coat of engine oil to the threads of the main bearing cap bolts.
![]() |
Install the 16 main bearing cap bolts. Using several steps, tighten the bolts uniformly in the sequence as shown in the illustration.
![]() |
Mark the front side of the bearing cap bolts with paint.
Retighten the bearing cap bolts 90° in the sequence as shown.
Check that the painted mark is now at a 90° angle to the front.
![]() |
Install the 8 main bearing cap bolts. Using several steps, tighten the bolts uniformly in the sequence as shown in the illustration.
Remove the main bearing caps.
![]() |
Measure the Plastigage at its widest point.
![]() |
If replacing a bearing, replace it with one that has the same number. If the number of the bearing cannot be determined, select the correct bearing by adding together the numbers imprinted on the cylinder block and crankshaft, then refer to the table below for appropriate bearing number. There are 5 sizes of standard bearings, marked "1", "2", "3", "4" and "5" accordingly.
| Cylinder block (A) + Crankshaft | Use Bearing |
| 0 - 5 | "1" |
| 6 - 11 | "2" |
| 12 - 17 | "3" |
| 18 - 23 | "4" |
| 24 - 28 | "5" |
| Item | Mark | mm (in.) |
| Cylinder block main journal bore diameter (A) | "00" | 77.000 (3.0315) |
| "01" | 77.001 (3.0315) | |
| "02" | 77.002 (3.0316) | |
| "03" | 77.003 (3.0316) | |
| "04" | 77.004 (3.0317) | |
| "05" | 77.005 (3.0317) | |
| "06" | 77.006 (3.0317) | |
| "07" | 77.007 (3.0318) | |
| "08" | 77.008 (3.0318) | |
| "09" | 77.009 (3.0319) | |
| "10" | 77.010 (3.0319) | |
| "11" | 77.011 (3.0319) | |
| "12" | 77.012 (3.0320) | |
| "13" | 77.013 (3.0320) | |
| "14" | 77.014 (3.0320) | |
| "15" | 77.015 (3.0321) | |
| "16" | 77.016 (3.0321) | |
| Crankshaft main journal diameter (B) | "00" | 71.999 to 72.000 (2.8346 to 2.8346) |
| "01" | 71.998 to 71.999 (2.8346 to 2.8346) | |
| "02" | 71.997 to 71.998 (2.8345 to 2.8346) | |
| "03" | 71.996 to 71.997 (2.8345 to 2.8346) | |
| "04" | 71.995 to 71.996 (2.8344 to 2.8345) | |
| "05" | 71.994 to 71.995 (2.8344 to 2.8344) | |
| "06" | 71.993 to 71.994 (2.8343 to 2.8344) | |
| "07" | 71.992 to 71.993 (2.8343 to 2.8343) | |
| "08" | 71.991 to 71.992 (2.8343 to 2.8343) | |
| "09" | 71.990 to 71.991 (2.8343 to 2.8343) | |
| "10" | 71.989 to 71.990 (2.8342 to 2.8343) | |
| "11" | 71.988 to 71.989 (2.8342 to 2.8342) | |
| Standard bearing center wall thickness | "1" | 2.488 to 2.491 (0.0980 to 0.0981) |
| "2" | 2.491 to 2.494 (0.0981 to 0.0982) | |
| "3" | 2.494 to 2.497 (0.0982 to 0.0983) | |
| "4" | 2.497 to 2.500 (0.0982 to 0.0984) | |
| "5" | 2.500 to 2.503 (0.0984 to 0.0985) |