CAMSHAFT > INSTALLATION |
| 1. INSTALL CAMSHAFT SUB GEAR |
![]() |
Install the gear spring [1], sub gear [2] and wave washer [3].
![]() |
Using snap ring pliers, install the snap ring.
![]() |
Mount the hexagonal portion of the camshaft in a vise.
![]() |
Using SST, align the holes of the driven main gear and sub gear by turning the sub gear clockwise. Temporarily install a service bolt.
Align the gear teeth of the driven main gear and sub gear, and tighten the service bolt.
| 2. INSTALL CAMSHAFT TIMING TUBE ASSEMBLY |
![]() |
Insert a new oil seal into the camshaft timing tube until it reaches the stopper.
![]() |
Align the timing tube knock pin with the knock pin groove of the drive gear, and temporarily install the drive gear with the 4 bolts.
Using SST and a 5 mm hexagon wrench, uniformly tighten the 4 bolts in several steps.
![]() |
Mount the hexagonal portion of the camshaft in a vise.
![]() |
Align the camshaft knock pin with the knock pin groove of the timing tube, and push the timing tube by hand until it touches the bottom.
Using a 10 mm hexagon wrench, install the bolt.
Install the seal washer and screw plug.
| 3. INSTALL CAMSHAFT (for RH Side) |
![]() |
![]() |
Apply engine oil to the thrust portion of the intake and exhaust camshafts.
Align the timing marks (1-dot mark) of the camshaft drive and driven main gears, and place the 2 camshafts.
Set the timing marks (1-dot mark) of the camshaft drive and driven main gears at approx. 10° angle.
![]() |
Apply seal packing to the camshaft housing plug.
![]() |
Install the camshaft housing plug and oil control valve filter to the cylinder head as shown in the illustration.
![]() |
Apply seal packing to the front bearing cap.
![]() |
Install the front bearing cap.
Install the other bearing caps in the order shown with the arrow mark facing forward.
![]() |
Push in the camshaft setting oil seal.
![]() |
Install new seal washers to the bearing cap bolts (A and B).
Apply a light coat of engine oil to the threads and under the heads of the bearing cap bolts (D and E).
Install the oil feed pipe and the 22 bearing cap bolts as shown in the illustration.
![]() |
Uniformly tighten the 22 bearing cap bolts in several steps, in the order shown in the illustration.
![]() |
Bring the service bolt installed in the driven sub-gear upward by turning the hexagonal portion of the camshaft with a wrench.
Remove the service bolt.
| 4. INSTALL CAMSHAFT (for LH Side) |
![]() |
Apply MP grease to the thrust portions of the camshafts.
Align the timing marks (2-dot marks) of the camshaft drive and driven main gears, and place the 2 camshafts.
![]() |
Apply seal packing to the camshaft housing plug.
![]() |
Install the camshaft housing plug and oil control valve filter to the cylinder head as shown in the illustration.
![]() |
Apply seal packing to the front bearing cap.
![]() |
Install the front bearing cap.
Install the other bearing cap in the order shown with the arrow mark facing forward.
![]() |
Push in the camshaft setting oil seal.
![]() |
Install a new seal washer to the bearing cap bolt (A and B).
Apply a light coat of engine oil to the threads and under the heads of the bearing cap bolts (D and E).
Install the camshafts of the LH bank.
Install the oil feed pipe and the 22 bearing cap bolts as shown in the illustration.
![]() |
Uniformly tighten the 22 bearing cap bolts in several steps, in the order shown in the illustration.
![]() |
Bring the service bolt installed in the driven sub-gear upward by turning the hexagonal portion of the camshaft with a wrench.
Remove the service bolt.
| 5. INSPECT VALVE CLEARANCE |
Turn the camshaft and position the cam lobe upward, and check and adjust the valve clearance .
| 6. INSTALL SEMICIRCULAR PLUG (for RH Side) |
![]() |
Remove any old packing (FIPG) material.
Apply seal packing to the semicircular plug grooves.
![]() |
Install the 2 semicircular plugs to the cylinder heads.
| 7. INSTALL SEMICIRCULAR PLUG (for LH Side) |
![]() |
Remove any old packing (FIPG) material.
Apply seal packing to the semicircular plug grooves.
![]() |
Install the 4 semicircular plugs to the cylinder heads.
| 8. INSTALL CAMSHAFT POSITION SENSOR |
| 9. INSTALL CAMSHAFT TIMING PULLEY SUB ASSEMBLY RH |
![]() |
Align the camshaft timing tube knock pin with the knock pin groove of the timing pulley.
Attach the timing pulley to the camshaft timing tube. Face the timing pulley's "R" mark forward.
Hold the hexagonal portion of the camshaft.
Using a 5 mm hexagon wrench, install the 4 bolts.
| 10. INSTALL CAMSHAFT TIMING PULLEY SUB-ASSEMBLY LH |
![]() |
Align the camshaft timing tube knock pin with the knock pin groove of the timing pulley.
Attach the timing pulley to the camshaft timing tube. Face the timing pulley's "L" mark forward.
Hold the hexagonal portion of the camshaft.
Using a 5 mm hexagon wrench, install the 4 bolts.
| 11. INSTALL CYLINDER HEAD COVER (for RH Side) |
![]() |
Remove any old packing (FIPG) material.
Apply seal packing to the cylinder heads as shown in the illustration.
Install the gasket to the cylinder head cover.
Install the seal washer to the bolt.
Install the cylinder head cover with the 18 bolts. Uniformly tighten the bolts in several steps. Install the 2 cylinder head covers.
| 12. INSTALL CYLINDER HEAD COVER (for LH Side) |
![]() |
Remove any old packing (FIPG) material.
Apply seal packing to the cylinder heads as shown in the illustration.
Install the gasket to the cylinder head cover.
Install the seal washer to the bolt.
Install the cylinder head cover with the 18 bolts. Uniformly tighten the bolts in several steps. Install the 2 cylinder head covers.
| 13. INSTALL IGNITION COIL ASSEMBLY |
Install the 4 bolts and ignition coil assembly.
| 14. INSTALL TIMING BELT |